CPFI-RA-2
CPFI-RA-2 Datasheet
CPFI-RA-2
| Part | Datasheet |
|---|---|
CPFI-RA-2 |
CPFI-RA-2 (pdf) |
| PDF Datasheet Preview |
|---|
| Right Angle Twist-On Plug Field Installable - 1 Piece INCHES MILLIMETERS CUSTOMER DRAWINGS AVAILABLE UPON REQUEST PART NUMBER CABLE TYPE CPFI-RA-2 RG-59, 62 WIRE GAUGE 22 WIRE DECIMAL JACKET O.D. Identify connector parts. 1 piece Trim cable as shown. Taking care not to nick the center conductor or outer braid. Use the fingernail to rotate the outer braids clockwise such that 1/32" of the insulation is bared. Then in the same direction rub the stray braids flat. Stray or loose braids can cause shorts. Gently insert the center conductor down the back end of the connector, feeling it into the guide hole. If the center conductor is not in place, approximately 1/8” of the center conductor - the part closest to the dielectric - will still be viewable. Firmly push the cable home a slight clockwise twist may help with insertion . Then screw the connector on the cable in a clockwise direction until it is snuggly attached to the jacket. Right angle connectors provide a lever to aid in twist, therefore do not over twist, which may cause the jacket and braids to eventually wear out. CABLE ASSEMBLY CAUTIONS • Series are designed for solid center conductor wire. RG-58 cable will need the center conductor tin dipped ONLY if it is not a solid center conductor . This is necessary to provide extra support for step • RG-MATV-59 cable will require caution when using the fingernail to rotate the braids on cable types that include aluminum foil for the outer conductor. DO NOT tear or rip the foil conductor to the 1/32” as suggested by step • RG-62 cable includes trimming the filament to 9/16” as well. Make sure that the filament does not unravel so that it protrudes past this dimension. Part Cable Wire Wire Jacket Number Type Gauge Decimal O.D. CPFI-RA-2 RG-59, 62 Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • • Fax 507-833-6287 • BNC Connectors Specifications INCHES MILLIMETERS CUSTOMER DRAWINGS AVAILABLE UPON REQUEST The BNC series connector is a commercial quality product that intermates with all standard double bayonet stud BNC designs. All contacts are captivated for ruggedness. The 50 ohm and 75 ohm interfaces are intermateable and provide quick, reliable connections for instrumentation, medical and LAN applications. Specifications* 50 Ohm BNC Electrical Characteristics Impedance 50 Ohm nominal Frequency range 0-4 GHz Working voltage 500 volts RMS at sea level Dielectric withstanding voltage 1500 volts RMS at sea level Corona level 375 volts minimum at 70,000 feet Contact resistance Outer - milliohms maximum Center - milliohms maximum Insulation resistance 5000 megohms minimum Environmental Characteristics Recommended temperature range -55OC to +85OC Moisture resistance MIL-STD-202 Mechanical Characteristics Durability 500 cycles Force to engage/disengage 3 lbs. maximum Cable retention 20 lbs., RG-58 C/U cable Materials Body Zinc or brass Contact Brass, beryllium copper or phosphor bronze Spring Washer Beryllium copper Crimp sleeve Brass Insulator or TPX Polymethylpentene Plating Body - Nickel except where noted Crimp sleeve - Nickel Contact - Gold * These values are typical and may not apply to all connectors. Cambridge Products, P.O. Box 1732, Waseca, MN 56093-0832 • • Fax 507-833-6287 • |
| More datasheets: 10325 | M42895 SL002 | M42895 SL001 | M42895 SL005 | FIT0016 | 2N5172_D26Z | 2N5172 | 2N5172_D27Z | 2N5172_D74Z | 2N5172_D75Z |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived CPFI-RA-2 Datasheet file may be downloaded here without warranties.