05045C272KAT1A

05045C272KAT1A Datasheet


0402 0504 0603 0805 1005 0907 1206 1210 1505 1805 1808 1812 1825 2225 3640

Part Datasheet
05045C272KAT1A 05045C272KAT1A 05045C272KAT1A (pdf)
Related Parts Information
05041A0R5CA79A 05041A0R5CA79A 05041A0R5CA79A
05041A470KA79A 05041A470KA79A 05041A470KA79A
05041A120KA79A 05041A120KA79A 05041A120KA79A
05041A121KA79A 05041A121KA79A 05041A121KA79A
05041A101KA79A 05041A101KA79A 05041A101KA79A
05041A820KA79A 05041A820KA79A 05041A820KA79A
05045C103JA19A 05045C103JA19A 05045C103JA19A
05045C821KAT1A 05045C821KAT1A 05045C821KAT1A
PDF Datasheet Preview
AVX Multilayer Ceramic Chip Capacitor

Ceramic Chip Capacitors

Table of Contents

MLC Chip Capacitors General Description How to Order - AVX Part Number Explanation C0G NP0 Dielectric

General Specifications Typical Characteristic Curves Capacitance Range X7R Dielectric General Specifications Typical Characteristic Curves Capacitance Range Z5U Dielectric General Specifications Typical Characteristic Curves Capacitance Range Y5V Dielectric General Specifications Typical Characteristic Curves Capacitance Range Low Profile Chips for Z5U & Y5V Dielectric High Voltage Chips for 500V to 5000V Applications General Specifications Mechanical Environmental MIL-C-55681/Chips Part Number Example Military Part Number Identification CDR01 thru CDR06 Military Part Number Identification CDR31 thru CDR35 Military Part Number Identification CDR31 Military Part Number Identification CDR32 Military Part Number Identification CDR33/34/35 European Version CECC 32 101-801 Chips Packaging of Chip Components Automatic Insertion Packaging Embossed Carrier Configuration - 8 & 12mm Tape 8 & 12mm Tape Punched Carrier Configuration - 8 & 12mm Tape 8 & 12mm Tape

Bulk Case Packaging

Surface Mounting Guide
1-6 7
8 9 10 - 11
12 13 14 - 15
16 17 18 - 19
20 21 22 23 24 - 25
26 27 - 28
29 30 31 32 33 34
38 39 40 - 43

Basic Construction A multilayer ceramic MLC capacitor is a monolithic block of ceramic containing two sets of offset, interleaved planar electrodes that extend to two opposite surfaces of the ceramic dielectric. This simple
structure requires a considerable amount of sophistication, both in material and manufacture, to produce it in the quality and quantities needed in today’s electronic equipment.

Ceramic Layer

Electrode

Terminated Edge

End Terminations

Terminated Edge

Margin

Electrodes

Formulations Multilayer ceramic capacitors are available in both Class 1 and Class 2 formulations. Temperature compensating formulation are Class 1 and temperature stable and general application formulations are classified as Class

Class 1 Class 1 capacitors or temperature compensating capacitors are usually made from mixtures of titanates where barium titanate is normally not a major part of the mix. They have predictable temperature coefficients and in general, do not have an aging characteristic. Thus they are the most stable capacitor available. Normally the T.C.s of multilayer ceramic capacitors are NP0 Class 1 temperature compensating capacitors negative-positive 0 ppm/°C .

Class 2 Class 2 capacitors are “ferro electric” and vary in capacitance value under the influence of the environmental and electrical operating conditions. Class 2 capacitors are affected by temperature, voltage both AC and DC , frequency and time. Temperature effects for Class 2 ceramic capacitors are exhibited as non-linear capacitance changes with temperature. The most common temperature stable formulation for MLCs is X7R while Z5U and Y5V are the most common general application formulations.

For additional information on performance changes with operating conditions consult AVX’s software, SpiCap.

Effects of Voltage Variations in voltage have little affect on Class 1 dielectric but does effect the capacitance and dissipation factor of Class 2 dielectrics. The application of DC voltage reduces both the capacitance and dissipation factor while the application of an AC voltage within a reasonable range tends to increase both capacitance and dissipation factor readings. If a high enough AC voltage is applied, eventually it will reduce capacitance just as a DC voltage will. Figure 2 shows the effects of AC voltage.

Cap. Change vs. A.C. Volts AVX X7R T.C.

Capacitance Change Percent

Figure 2

Volts AC at KHz

Capacitor specifications specify the AC voltage at which to measure normally or 1 VAC and application of the wrong voltage can cause spurious readings. Figure 3 gives the voltage coefficient of dissipation factor for various AC voltages at 1 kilohertz. Applications of different frequencies will affect the percentage changes versus voltages.

D.F. vs. A.C. Measurement Volts AVX X7R T.C.

Dissipation Factor Percent

Curve 1 - 100 VDC Rated Capacitor Curve 2 - 50 VDC Rated Capacitor

Curve 3 - 25 VDC Rated Capacitor

Curve 3 Curve 2

Curve 1

AC Measurement Volts at KHz
More datasheets: LFR-206WW28V | LFR-206Y12V | LFR-206Y28V | LFR-206CW12V | LFR-206CW28V | HSHM-S095B4-5AP1-TR40B | HSHM-S095B1-5AP1-TR40B | 05041A0R5CA79A | 05041A470KA79A | 05041A120KA79A


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 05045C272KAT1A Datasheet file may be downloaded here without warranties.

Datasheet ID: 05045C272KAT1A 521428