70-841-016

70-841-016 Datasheet

Astec connector kit #70-841-016

Part	Datasheet
70-841-016	70-841-016 (pdf)

PDF Datasheet Preview
175 Watts LPS170 Series Total Power 110-175 Watts Input Voltage 85-264 VAC 120-300 VDC # of Outputs Single Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter Power factor Safety ground leakage current 85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start 25°C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted typical mA 50/60 Hz, 264 VAC input Special Features • Active power factor correction • IEC EN61000-3-2 compliance • Wide Range Adjustable output Remote sense on main output • Single wire current sharing • Power fail and remote inhibit • Built-in EMI filter • Low output ripple • Overvoltage protection • Overload protection • Thermal overload protection • DC power good • 5 V standby output • 12 V Aux output • Optional cover -C suffix Environmental Operating temperature 0° to 50°C ambientderate each output at per degree from 50° to 70°C Electromagnetic susceptibility designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity Operating non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances G peak 5 Hz to 500 Hz, operational Storage temperature -40° to 85°C Temperature coefficient ± per °C MTBF demonstrated >550,000 hours at full load and 25°C ambient conditions Output Maximum power Adjustment range Hold-up time Overload protection Overvoltage protection Standby output Aux output 110 W convection 75 W with cover 175 W with 30 CFM forced air 130 W with cover 2:1 wide ratio minimum 20 ms W load at nominal line Short circuit protection on all outputs. Case overload protected 110-145% above peak rating 10% to 40% above nominal output 5 V 2A regulated ±5% 12 V 1 A -5 %, +10% Logic Control Power failure Remote inhibit Remote sense DC Ok TTL logic signal goes high 100 - 500 msec after V1 output It goes low at least 4 msec before loss of regulation Requires contact closure to inhibit outputs TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling LPS172 LPS173 LPS174 LPS175 5 V 2.5-6V 12 V 6-12 V 15 V 12-24 V 24 V 24-54 V Maximum Load with 30 CFM Forced Air 35 A 15 A 12 A Peak Load Regulation2 ±2% ±2% ±2% ±2% Ripple P/P PARD 3 50 mV 120 mV <1% <1% Peak current lasting <30 seconds with a maximum 10% duty cycle. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a µF capacitor at rated line voltage and load ranges. Remote inhibit resets OVP latch Note -C suffix added to the model number indicates cover option. Ordering Information Connector LPS17x PIN 1 +12V PIN 2 5V Standby PIN 3 Common PIN 4 V1 SWP PIN 5 Common PIN 6 +V1 sense PIN 7 Sense common PIN 8 Remote inhibit PIN 9 DC power good PIN 10 TB-1 COMMON TB-2 Main output PIN 1 GROUND PIN 3 LINE PIN 5 NEUTRAL Mating Connectors SK4 AC Input: Molex 09-50-8051 USA Molex 09-91-0500 UK PINS 08-58-0111 SK3 DC Output: Molex 19141-0058 SK1 Control Signals: Molex 90142-0010 USA PINS 90119-2110 or Amp 87977-3 PINS 87309-8 Astec connector kit #70-841-016 Notes Specifications subject to change without notice. All dimensions in inches mm , tolerance is Specifications are for convection rating at factory settings unless otherwise stated. Mounting screw maximum insertion depth is Warranty 1 year Weight lb / kg +SK3 Voltage Adj POT

PDF Datasheet Preview

175 Watts

LPS170 Series

Total Power 110-175 Watts Input Voltage 85-264 VAC
120-300 VDC # of Outputs Single

Electrical Specs

Input

Input range Frequency Inrush current Efficiency EMI filter

Power factor Safety ground leakage current
85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start 25°C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted typical
mA 50/60 Hz, 264 VAC input

Special Features
• Active power factor correction
• IEC EN61000-3-2 compliance
• Wide Range Adjustable output

Remote sense on main output
• Single wire current sharing
• Power fail and remote inhibit
• Built-in EMI filter
• Low output ripple
• Overvoltage protection
• Overload protection
• Thermal overload protection
• DC power good
• 5 V standby output
• 12 V Aux output
• Optional cover -C suffix

Environmental

Operating temperature 0° to 50°C ambientderate each output at per degree from 50° to 70°C

Electromagnetic susceptibility designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3

Humidity Operating non-condensing
5% to 95%

Vibration Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances G peak 5 Hz to 500 Hz, operational

Storage temperature -40° to 85°C

Temperature coefficient ± per °C

MTBF demonstrated >550,000 hours at full load and 25°C ambient conditions

Output

Maximum power

Adjustment range Hold-up time Overload protection

Overvoltage protection Standby output Aux output
110 W convection 75 W with cover 175 W with 30 CFM forced air 130 W with cover
2:1 wide ratio minimum
20 ms W load at nominal line

Short circuit protection on all outputs. Case overload protected 110-145% above peak rating
10% to 40% above nominal output
5 V 2A regulated ±5%
12 V 1 A -5 %, +10%

Logic Control

Power failure

Remote inhibit Remote sense

DC Ok

TTL logic signal goes high 100 - 500 msec after V1 output It goes low at least 4 msec before loss of regulation

Requires contact closure to inhibit outputs

TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation
Ordering Information

Model Number

Output Voltage

Minimum Load

Maximum Load with Convection Cooling

LPS172 LPS173 LPS174 LPS175
5 V 2.5-6V
12 V 6-12 V
15 V 12-24 V
24 V 24-54 V

Maximum Load with 30 CFM Forced Air
35 A 15 A 12 A

Peak Load

Regulation2
±2% ±2% ±2% ±2%

Ripple P/P PARD 3
50 mV 120 mV <1% <1%

Peak current lasting <30 seconds with a maximum 10% duty cycle. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a µF capacitor at rated line voltage and load ranges. Remote inhibit resets OVP latch

Note -C suffix added to the model number indicates cover option.
Ordering Information

Connector LPS17x

PIN 1
+12V

PIN 2
5V Standby

PIN 3

Common

PIN 4

V1 SWP

PIN 5

Common

PIN 6
+V1 sense

PIN 7

Sense common

PIN 8

Remote inhibit

PIN 9

DC power good

PIN 10

TB-1

COMMON

TB-2

Main output

PIN 1

GROUND

PIN 3

LINE

PIN 5

NEUTRAL

Mating Connectors SK4 AC Input:

Molex 09-50-8051 USA Molex 09-91-0500 UK PINS 08-58-0111

SK3 DC Output:

Molex 19141-0058

SK1 Control Signals:

Molex 90142-0010 USA PINS 90119-2110 or Amp 87977-3 PINS 87309-8

Astec connector kit #70-841-016

Notes Specifications subject to change without notice. All dimensions in inches mm , tolerance is Specifications are for convection rating at factory settings unless otherwise stated. Mounting screw maximum insertion depth is Warranty 1 year Weight lb / kg
+SK3

Voltage Adj POT

More datasheets: FM27C256Q120 | FM27C256Q150 | FM27C256V150 | FM27C256V120 | 2428 | HLMP-FW00-JM000 | M2485 SL005 | M2485 SL002 | M2485 SL001 | FDZ4010

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 70-841-016 Datasheet file may be downloaded here without warranties.

Datasheet ID: 70-841-016 518833