DP4048N2M

DP4048N2M Datasheet

DP40 40 Watts

Part	Datasheet
DP4048N2M	DP4048N2M (pdf)

Related Parts	Information
DP4024N2M	DP4024N2M
DP4048N3M	DP4048N3M
DP4009N2M	DP4009N2M
DP4018N3M	DP4018N3M
DP4018N2M	DP4018N2M
DP4015N2M	DP4015N2M
DP4015N3M	DP4015N3M
DP4009N3M	DP4009N3M
DP4024N3M	DP4024N3M
DP4012N2M	DP4012N2M
DP4012N3M	DP4012N3M

PDF Datasheet Preview
POWER Data Sheet DP40 40 Watts Total Power 40 Watts Input Voltage 90 - 264 Vac 127 - 300 Vdc # of Outputs Single SPECIAL FEATURES Medical and ITE safeties Universal AC input Fully regulated output Overload and short circuit protection Constant voltage High efficiency High MTBF IEC320 AC input receptacle 3 pin type C14 Class I 2 pin type C8 Class II Built in EMI filter CISPR 22 Class B LED power good indicator Input power <49 watts Complies with EN61000-3-2 Meets Energy Star Efficiency Level V CE Mark EMC, LVD & ErP 2011 Less than 300 mW No-Load power consumption SAFETY UL cUL TUV CE CB CCC 60950-1, 60601-1 60950-1, 60601-1 60950-1, 60601-1 EMC, LVD & ErP 2011 Certificate and report China Approval Electrical Specifications Input Input range 90 - 264 Vac wide range 127 - 300 Vdc Frequency 47 - 63 Hz Inrush current < 50 A 230 Vac, cold start 25 °C Input current < A rms 115 Vac < A 230 Vac Efficiency 84% full load typical, Vac EMI/RFI FCC Part 15, Subpart B Class B & EN55022 CISPR 22 Class B Safety ground leakage current 300 uA 50/60 Hz, 264 Vac input for 3 pin model 100 uA 50/60 Hz, 264 Vac input for 2 pin model Output Maximum power Po Hold-up time 10 ms. typical at full load 115 Vac Overvoltage protection 20% - 45% above nominal output maximum Latching type, recycle AC to reset. Overload protection Output short circuit protection auto recover Overload protected 110 - 160% above peak rating Cable/connector m DC cable with mm I.D, mm O.D center plug DC plug center +v DC plug outer -v Environmental Specifications Operating temperature 0 ° to +40 °C ambient. Derate each output as per degree from 40 °C to 60 °C. -20 °C start up Storage temperature Ordering Information Model Number Output Voltage DP4009N2M DP4009N3M DP4012N2M DP4012N3M DP4015N2M DP4015N3M DP4018N2M DP4018N3M DP4024N2M DP4024N3M DP4048N2M DP4048N3M Maximum Load Peak Load1 Regulation2 ± 8% ± 8% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% Peak current lasting < 15 seconds with a maximum 10% duty cycle. At 25 ºC including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 uF tantalum capacitor in parallel with a uF capacitor at rated line voltage and load ranges. Mechanical Drawing Ripple P/P PARD 3 90 mV 90 mV 120 mV 120 mV 150 mV 150 mV 150 mV 150 mV 240 mV 240 mV 480 mV 480 mV 48" 1219 ± 20 Notes Specifications subject to change without notice. All dimensions in inches mm , tolerance is ± ± mm Warranty 2 year Weight lb./.25 kg AC input power cord sold separately. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C unless otherwise stated 48" 1219 ± 20 Americas 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 WORLDWIDE OFFICES Europe UK Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 0 1384 842 211 Asia HK 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. 2015 Artesyn Embedded Technologies, Inc. For more information For support: DP40-DS 09Jul2015

PDF Datasheet Preview

POWER

Data Sheet

DP40 40 Watts

Total Power 40 Watts Input Voltage 90 - 264 Vac
127 - 300 Vdc # of Outputs Single

SPECIAL FEATURES

Medical and ITE safeties Universal AC input Fully regulated output Overload and short circuit protection Constant voltage High efficiency High MTBF IEC320 AC input receptacle
3 pin type C14 Class I 2 pin type C8 Class II Built in EMI filter CISPR 22 Class B LED power good indicator Input power <49 watts Complies with EN61000-3-2 Meets Energy Star Efficiency Level V CE Mark EMC, LVD & ErP 2011 Less than 300 mW No-Load power consumption

SAFETY

UL cUL TUV CE CB CCC
60950-1, 60601-1 60950-1, 60601-1 60950-1, 60601-1 EMC, LVD & ErP 2011 Certificate and report

China Approval

Electrical Specifications

Input

Input range
90 - 264 Vac wide range 127 - 300 Vdc

Frequency
47 - 63 Hz

Inrush current
< 50 A 230 Vac, cold start 25 °C

Input current
< A rms 115 Vac < A 230 Vac

Efficiency
84% full load typical, Vac

EMI/RFI

FCC Part 15, Subpart B Class B & EN55022 CISPR 22 Class B

Safety ground leakage current 300 uA 50/60 Hz, 264 Vac input for 3 pin model 100 uA 50/60 Hz, 264 Vac input for 2 pin model

Output

Maximum power Po

Hold-up time
10 ms. typical at full load 115 Vac

Overvoltage protection
20% - 45% above nominal output maximum Latching type, recycle AC to reset.

Overload protection

Output short circuit protection auto recover Overload protected 110 - 160% above peak rating

Cable/connector
m DC cable with mm I.D, mm O.D center plug DC plug center +v DC plug outer -v

Environmental Specifications

Operating temperature
0 ° to +40 °C ambient. Derate each output as per degree from 40 °C to 60 °C. -20 °C start up

Storage temperature
Ordering Information

Model Number

Output Voltage

DP4009N2M

DP4009N3M

DP4012N2M

DP4012N3M

DP4015N2M

DP4015N3M

DP4018N2M

DP4018N3M

DP4024N2M

DP4024N3M

DP4048N2M

DP4048N3M

Maximum Load

Peak Load1

Regulation2
± 8% ± 8% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5% ± 5%

Peak current lasting < 15 seconds with a maximum 10% duty cycle. At 25 ºC including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 uF tantalum capacitor in parallel with a uF capacitor at rated line voltage and load ranges.

Mechanical Drawing

Ripple P/P PARD 3
90 mV 90 mV 120 mV 120 mV 150 mV 150 mV 150 mV 150 mV 240 mV 240 mV 480 mV 480 mV
48" 1219 ± 20

Notes Specifications subject to change without notice. All dimensions in inches mm , tolerance is ± ± mm Warranty 2 year Weight lb./.25 kg AC input power cord sold separately. Specifications are for convection rating at factory settings at 115 Vac input, 25 °C
unless otherwise stated
48" 1219 ± 20

Americas
2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832

WORLDWIDE OFFICES

Europe UK

Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 0 1384 842 211

Asia HK
14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333

While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. 2015 Artesyn Embedded Technologies, Inc.

For more information For support:

DP40-DS 09Jul2015

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived DP4048N2M Datasheet file may be downloaded here without warranties.

Datasheet ID: DP4048N2M 518824