ABX00017

ABX00017 Datasheet

Code ABX00017

Part	Datasheet
ABX00017	ABX00017 (pdf)

PDF Datasheet Preview
ARDUINO MKR WAN 1300 LORA CONNECTIVITY Code ABX00017 MKR WAN 1300 is a powerful board that combines the functionality of the MKR Zero and LoRa connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device. Arduino MKR WAN 1300 has been designed to offer a practical and cost effective solution for makers seeking to add Lo-Ra connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a Murata CMWX1ZZABZ Lo-Ra module. The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the MKR ZERO board, the usual rich set of I/O interfaces, low power Lo-Ra communication and the ease of use of the Arduino Software IDE for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power 5V to the board. The Arduino MKR WAN 1300 is able to run with or without the batteries connected and has limited power consumption. Warning Unlike most Arduino & Genuino boards, the MKR WAN 1300 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting TECH SPECS Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU Board Power Supply USB/VIN Supported Batteries * 2x AA or AAA Circuit Operating Voltage 3.3V Digital I/O Pins PWM Pins 12 0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19 UART Analog Input Pins 7 ADC 8/10/12 bit Analog Output Pins 1 DAC 10 bit External Interrupts 8 0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17 DC Current per I/O Pin Flash Memory 256 KB SRAM 32 KB EEPROM Clock Speed kHz RTC , 48 MHz LED_BUILTIN Full-Speed USB Device and embedded Host Antenna power Carrier frequency 433/868/915 MHz Working region EU/US Length Width 25 mm Weight

PDF Datasheet Preview

ARDUINO MKR WAN 1300 LORA CONNECTIVITY

Code ABX00017

MKR WAN 1300 is a powerful board that combines the functionality of the MKR Zero and LoRa connectivity. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking having a low power device.

Arduino MKR WAN 1300 has been designed to offer a practical and cost effective solution for makers seeking to add Lo-Ra connectivity to their projects with minimal previous experience in networking. It is based on the Atmel SAMD21 and a Murata CMWX1ZZABZ Lo-Ra module. The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically. A good 32 bit computational power similar to the MKR ZERO board, the usual rich set of I/O interfaces, low power Lo-Ra communication and the ease of use of the Arduino Software IDE for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor. The USB port can be used to supply power 5V to the board. The Arduino MKR WAN 1300 is able to run with or without the batteries connected and has limited power consumption. Warning Unlike most Arduino & Genuino boards, the MKR WAN 1300 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting

TECH SPECS

Microcontroller

SAMD21 Cortex-M0+ 32bit low power ARM MCU

Board Power Supply USB/VIN

Supported Batteries *
2x AA or AAA

Circuit Operating Voltage
3.3V

Digital I/O Pins

PWM Pins
12 0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19

UART

Analog Input Pins
7 ADC 8/10/12 bit

Analog Output Pins
1 DAC 10 bit

External Interrupts
8 0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17

DC Current per I/O Pin

Flash Memory
256 KB

SRAM
32 KB

EEPROM

Clock Speed
kHz RTC , 48 MHz

LED_BUILTIN

Full-Speed USB Device and embedded Host

Antenna power

Carrier frequency
433/868/915 MHz

Working region

EU/US

Length

Width
25 mm

Weight

More datasheets: B43305B5187M67 | B43305A9277M82 | B43305A9277M87 | B43305A9277M80 | B43305A2108M62 | B43305A9277M60 | B43305A9277M62 | B43305A9277M67 | B43305A5687M000 | AOD472

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ABX00017 Datasheet file may be downloaded here without warranties.

Datasheet ID: ABX00017 518327