Part | Datasheet |
---|---|
![]() |
BD150SD4BL1200 (pdf) |
Related Parts | Information |
---|---|
![]() |
BD150D02BK1200 |
![]() |
BD140D01GR0000 |
![]() |
BD150A01RE0000 |
PDF Datasheet Preview |
---|
an APEM Group Company BF series Paddle controllers The BF Series Paddle is the very latest generation in high precision contactless controls. It combines the features of a contactless single axis joystick and a switch in one control. Long trouble-free life is assured with the latest Hall effect technology, providing a range of analog, switched or custom PWM output options. The all-new design with its innovative mechanism and ergonomic styling is specifically designed for robustness, strength and performance. KEY FEATURES Hall effect joystick and switch function Sculpted ergonomic design Next generation Hall effect technology 5V operation - dual redundant outputs as standard Two lever height variants Industry standard connector IP67 sealed Sprung and detent lever options Available with color-coded inserts EMC & Magnetically shielded - analog or PWM outputs Effectively zero below panel depth End stackable mounting BF series Paddle controllers OPTION SELECTION PADDLE BF 74mm 2.91in above the panel BD 50mm 1.97in above the panel GAIN +/-10% x V +/-25% x V +/-30% x V +/-40% x V +/-50% x V INSERT COLOR Black Blue Yellow Green MODIFIER 00 None CONFIGURATION Standard Dual Outputs Inverse Dual Outputs A01 D01 D02 D03 D04 SD1 SD2 SD3 SD4 LEVER OPERATION Sprung to Center Detent Degree Detents & 25 Degree Detents 25 Degree Detents Sprung to Center with D1 Sprung to Center with D2 Sprung to Center with D3 Sprung to Center with D4 SWITCHING POINTS No Switches +/- 5 Degrees +/- Degrees +/- 25 Degrees LEVER OPERATION D01 = CENTER DETENT DETENT OPTIONS D02 = DEGREES D03 = +/- & 25 DEGREES D04 = +/-25 DEGREES ADDITIONAL OUTPUT INFORMATION SELECTABLE SWITCHING POINTS The Paddle incorporates two Hall effect switches. The angle of the lever at the switch trigger point can be selected when ordering. If no switches are specified then the output on pins 2 and 7 will be unused. The outputs are configured as ‘open drain’ type with a 1K5 pull up resistor to 5V. GAIN OPTIONS The voltage output on the wiper, at full scale deflection is determined by the gain. The gain is expressed as a percentage of the voltage supplied. Therefore assuming a 5V supply a Paddle specified with +/- 25% gain would yield 1.25V at South, 2.5V at center and 3.75V at North. A range of gain options are available as standard. All controls are supplied pre-set and no further calibration is needed throughout the lifetime of operation. OUTPUT IMPEDANCE The voltage outputs at center and at each end of travel are specified across an infinite load, with no current flowing. The output impedance specified in the electrical specification should be taken into account when designing a system. Load resistance of less than 10K Ohms is not recommended. HANDLE OPTIONS The BF Series offers two standard handle options. The taller 74mm handle provides the most ergonomic solution while the shorter 50mm is best suited to hand held applications where a minimized height is preferred. The taller lever is supplied with the top insert prefitted, however the shorter lever may be specified with no insert fitted and the snap in inserts supplied loose for ease of customer integration. Note The company reserves the right to change specifications without notice. BF series Paddle controllers APPLICATION DETAILS LINEAR OUTPUT OPTIONS OUTPUT VOLTAGE V - - - - - - - - - - +/-50% AXES TRAVEL º +/-50% AXES TRAVEL º DUAL OUTPUT - CONFIGURATION 3 +/-40% +/-30% AXES TRAVEL º AXES TRAVEL º DUAL OUTPUT - CONFIGURATION 4 +/-40% +/-30% AXES TRAVEL º AXES TRAVEL º +/-25% AXES TRAVEL º +/-25% AXES TRAVEL º +/-10% AXES TRAVEL º MAX +/-10% AXES TRAVEL º MAX Output 1 Output 2 OUTPUT VOLTAGE V POWER SUPPLY The BF Series is designed to be powered by a regulated 5V+/- 0.5V power supply. The outputs are ratiometric, making a stable, noise free, power supply essential. The power supply to the joystick should be carefully regulated to be within tolerance. Should the power supply change outside of the specified tolerances, permanent damage may occur. MAGNETIC IMMUNITY AND SYSTEM DESIGN The BF Series incorporates internal magnetic screening to minimize the effect of external magnetic fields. Mounting or operating the Paddle close to strong magnetic fields is not recommended. System designers should follow best practice when incorporating the BF Series Paddle into their products. Care should be taken to decouple the power supply properly and to employ adequate EMC shielding. MOUNTING When mounting the Paddle, care should be taken to site it in a position that does not make it vulnerable to damage when in use. If the Paddle is intended for use in a handheld enclosure then care must be taken to protect the Paddle from damage caused by dropping. Basic precautions such as mounting it at the lightest end of the enclosure so it doesn’t hit the ground first or by protecting it with a guard should always be implemented for long term reliability. The body of the Paddle, on the underside of the panel, must not be subject to water spray, excessive humidity or dust. Note The company reserves the right to change specifications without notice. |
More datasheets: QTLP9124GR | QTLP9124ZR | QTLP9132GR | QTLP9137GR | 5561909304F | 70-841-013 | AA20140 | 5118NL | BD150D02BK1200 | BD140D01GR0000 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived BD150SD4BL1200 Datasheet file may be downloaded here without warranties.