HMC435MS8GE

HMC435MS8GE Datasheet


HMC435MS8G / 435MS8GE

Part Datasheet
HMC435MS8GE HMC435MS8GE HMC435MS8GE (pdf)
PDF Datasheet Preview
HMC435MS8G / 435MS8GE
v05.0110

SPDT NON-REFLECTIVE SWITCH, DC - 4 GHz

The HMC435MS8G E is ideal for
• Basestations & Repeaters
• Cellular/3G and WiMAX/4G
• Infrastructure and Access Points
• CATV/CMTS
• Test Instrumentation

Functional Diagram

High Isolation 60 dB 1 GHz 50 dB 2 GHz

Positive Control 0/+5V Input IP3 51 dBm Non-Reflective Design Ultra Small MSOP-86 Package mm2

The HMC435MS8G E is a non-reflective DC to 4 GHz GaAs MESFET SPDT switch in a low cost 8 lead MSOP8G surface mount package with exposed ground paddle. The switch is ideal for cellular/3G and WiMAX/4G applications yielding up to 60 dB isolation, low dB insertion loss and +50 dBm input IP3. Power handling is excellent up through the GHz WiMAX band with the switch offering a P1dB compression of +31 dBm. On-chip circuitry allows positive voltage control of 0/+5 Volts at very low DC currents.

SWITCHES - SPDT - SMT

Electrical Specifications, TA = +25° C, Vctl = 0/+5 Vdc, 50 Ohm System

Insertion Loss

Parameter

Isolation RFC to RF1/RF2

Return Loss On State

Return Loss Off State Input Power for 1 dB Compression

Input Third Order Intercept Two-Tone Input Power = +7 dBm Each Tone

Switching Speed
tRISE, tFALL 10/90% RF tON, tOFF 50% CTL to 10/90% RF

Frequency

DC - GHz DC - GHz DC - GHz

DC - GHz DC - GHz DC - GHz DC - GHz DC - GHz

DC - GHz DC - GHz DC - GHz
- GHz
- GHz
- GHz - GHz - GHz

DC - GHz

Min.

Typ.
40 60

Max.

Units
11 - 122

For price, delivery, and to place orders, please contact Hittite Microwave Corporation 20 Alpha Road, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at

HMC435MS8G / 435MS8GE
v05.0110

SPDT NON-REFLECTIVE

SWITCH, DC - 4 GHz

Insertion Loss

INSERTION LOSS dB
+ 25C
+ 85C
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material Rogers 4350

The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request.

Note Pin J6 is unused and need not be connected.

For price, delivery, and to place orders, please contact Hittite Microwave Corporation 20 Alpha Road, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at
11 - 125
More datasheets: 26222 | FGA90N33ATTU | 13910 | TEL0075 | A-DSUB-05-42-28-100 | DM74AS1004AMX | DM74AS1004AN | DM74AS1004AM | PI5USB1457ZAEX | PI5USB1457AZAEX


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HMC435MS8GE Datasheet file may be downloaded here without warranties.

Datasheet ID: HMC435MS8GE 517939