HMC221AE

HMC221AE Datasheet

HMC221A / 221AE

Part	Datasheet
HMC221AE	HMC221AE (pdf)

Related Parts	Information
101675-HMC221A	101675-HMC221A

PDF Datasheet Preview
HMC221A / 221AE v02.0911 GaAs MMIC SOT26 SPDT SWITCH, DC - 3 GHz Switches - SPDT - SMT The HMC221A E is ideal for • ISM Applications • PCMCIA Wireless Cards • Cellular Applications Functional Diagram RoHS-Compliant Product Low Insertion Loss dB Ultra Small Package SOT26 Input IP3 +45 dBm Positive Control 0/+3V 3 µA Included in the HMC-DK005 Designer’s Kits The HMC221A E is a low-cost SPDT switch in a 6-lead SOT26 plastic package for use in general switching applications which require very low insertion loss and very small size. This device can control signals from DC to 3 GHz and is especially suited for 900 MHz, - GHz, and GHz ISM applications with less than 1 dB loss. The design provides exceptional insertion loss performance, ideal for filter and receiver switching. RF1 and RF2 are reflective shorts when “Off”. The two control voltages require a minimal amount of DC current and offer compatibility with most CMOS & TTL logic families. See HMC197A E for same performance in an alternate SOT26 pin-out. Electrical Specifications, TA = +25° C, Vctl = 0/+3 to +8 Vdc Insertion Loss Isolation Parameter Frequency DC - GHz DC - GHz DC - GHz DC - GHz DC - GHz DC - GHz DC - GHz DC - GHz Min. Typ. Max. Units Return Loss DC - GHz DC - GHz DC - GHz DC - GHz Input Power for 1 dB Compression Vctl = 0/+5V - GHz - GHz Input Third Order Intercept Vctl = 0/+5V Two-tone Input Power = +7 dBm Each Tone - GHz - GHz Switching Characteristics DC - GHz tRISE, tFALL 10/90% RF tON, tOFF 50% CTL to 10/90% RF For price, delivery and to place orders Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at Application Support Phone 978-250-3343 or v02.0911 HMC221A / 221AE [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material Rogers 4350 The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request. For price, delivery and to place orders Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone 978-250-3343 Fax 978-250-3373 Order On-line at Application Support Phone 978-250-3343 or

PDF Datasheet Preview

HMC221A / 221AE
v02.0911

GaAs MMIC SOT26 SPDT

SWITCH, DC - 3 GHz

Switches - SPDT - SMT

The HMC221A E is ideal for
• ISM Applications
• PCMCIA Wireless Cards
• Cellular Applications

Functional Diagram

RoHS-Compliant Product

Low Insertion Loss dB

Ultra Small Package SOT26

Input IP3 +45 dBm

Positive Control 0/+3V 3 µA

Included in the HMC-DK005 Designer’s Kits

The HMC221A E is a low-cost SPDT switch in a 6-lead SOT26 plastic package for use in general switching applications which require very low insertion loss and very small size. This device can control signals from DC to 3 GHz and is especially suited for 900 MHz, - GHz, and GHz ISM applications with less than 1 dB loss. The design provides exceptional insertion loss performance, ideal for filter and receiver switching. RF1 and RF2 are reflective shorts when “Off”. The two control voltages require a minimal amount of DC current and offer compatibility with most CMOS & TTL logic families. See HMC197A E for same performance in an alternate SOT26 pin-out.

Electrical Specifications, TA = +25° C, Vctl = 0/+3 to +8 Vdc

Insertion Loss Isolation

Parameter

Frequency

DC - GHz DC - GHz DC - GHz DC - GHz

DC - GHz DC - GHz DC - GHz DC - GHz

Min.

Typ.

Max.

Units

Return Loss

DC - GHz

DC - GHz

DC - GHz

DC - GHz

Input Power for 1 dB Compression Vctl = 0/+5V
- GHz - GHz

Input Third Order Intercept Vctl = 0/+5V Two-tone Input Power = +7 dBm Each Tone
- GHz - GHz

Switching Characteristics

DC - GHz
tRISE, tFALL 10/90% RF tON, tOFF 50% CTL to 10/90% RF

For price, delivery and to place orders Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824

Phone 978-250-3343 Fax 978-250-3373 Order On-line at

Application Support Phone 978-250-3343 or
v02.0911

HMC221A / 221AE
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material Rogers 4350

The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines at the RF port should have 50 Ohm impedance and the package ground leads and package bottom should be connected directly to the ground plane similar to that shown above. The evaluation circuit board shown above is available from Hittite Microwave Corporation upon request.

For price, delivery and to place orders Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824

Phone 978-250-3343 Fax 978-250-3373 Order On-line at

Application Support Phone 978-250-3343 or

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived HMC221AE Datasheet file may be downloaded here without warranties.

Datasheet ID: HMC221AE 517924