EVAL-8MSOPEBZ

EVAL-8MSOPEBZ Datasheet

Evaluation Board for 8 lead MSOP devices in the Switch/Mux portfolio

Part	Datasheet
EVAL-8MSOPEBZ	EVAL-8MSOPEBZ (pdf)

PDF Datasheet Preview
Preliminary Technical Data UG-xxx One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel • Fax • Evaluation Board for 8 lead MSOP devices in the Switch/Mux portfolio 8 lead MSOP evaluation board Clamp to allow the main device to be changed easily Gold pin connectors to allow the addition of passive components SMB connectors for the input/output of signals Additional space on board to allow for prototyping EVALUATION KIT CONTENTS EVAL-8MSOPEBZ evaluation board ONLINE RESOURCES Documents Needed Data sheet of the device to be evaluated EVAL-8MSOPEBZ user guide EQUIPMENT NEEDED Device to be evaluated DC voltage source Analog signal source Method to measure voltage, such as a digital multimeter DMM The EVAL-8MSOPEBZ is the evaluation board for the 8 lead MSOP devices in the switch/mux portfolio which are to be purchased separately. A clamp is supplied with the board so that the device can be secured to the board without the need for soldering. This makes the board reusable for multiple devices. Figure 1 shows the EVAL-8MSOPEBZ evaluation board. The device can be clamped or soldered to the center of the evaluation board. Each pin of the device is broke out to a link that can be set to either VDD or GND and a wire screw terminal is provided to supply VDD and GND. SMB connectors are on the board allow for additional external signals to be supplied to the device. In addition, there is space at the top of the board available for prototyping. Full specifications of the device under test are available in the product data sheet, which should be consulted in conjunction with this user guide when using the evaluation board. EVALUATION BOARD PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. UG-xxx TABLE OF CONTENTS 0 Initial Version Preliminary Technical Data Power Link SMB Connectors Input Signal Evaluation Board Schematics and Ordering Bill of Preliminary Technical Data EVALUATION BOARD HARDWARE The operation of a 8 lead MSOP devices in the switch/mux portfolio can be evaluated using the EVAL-8MSOPEBZ. Figure 1 shows the evaluation board. POWER SUPPLY Connector J5 provides the ability to supply VDD and GND supplies to the board. These can them be selected for each pin of the device by setting the link headers to either VDD or GND. If a VSS supply is needed then the voltage can applied directly to the pin of the device. An example of how this can be done is by removing the link and then supplying the required voltage to the central pin of the header or to the gold pin connectors on the relevant trace. LINK HEADERS The link headers are used to supply the device under test with either VDD or GND. Each header is designated K1 to K8, with the number corresponding to the pin number of the device. Table 1 shows a summary of the link headers and how they function on the evaluation board. Table Link Header Descriptions Label Position Description K1to K8 H UG-xxx SMB CONNECTORS They are four SMB connectors on evaluation board labelled J1 to J4. When an SMB cable is one of these connectors, the signal becomes available on either P1 to P4. This signal can then be applied to the pin of the device by forming a connection from either P1 to P4 to a gold pin connector found on the relevant trace. INPUT SIGNAL TRACES Each trace includes three sets of gold pin connectors, two of which can be used to place a load on the signal path to ground and another that is in series with the signal path. The three sets of gold pin connectors can be used to create a simple resistorcapacitor RC filter. UG-xxx EVALUATION BOARD SCHEMATICS AND ARTWORK Preliminary Technical Data Figure ADG5208F Evaluation Board Schematic Figure EVAL-ADG5208FEBZ Silkscreen Preliminary Technical Data Figure EVAL-ADG5208FEBZ Bottom Layer UG-xxx UG-xxx ORDERING INFORMATION BILL OF MATERIALS Table Preliminary Technical Data Preliminary Technical Data NOTES UG-xxx ESD Caution ESD electrostatic discharge sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. 2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG13456-0-8/15 0

PDF Datasheet Preview

Preliminary Technical Data

UG-xxx

One Technology Way
• P.O. Box 9106
• Norwood, MA 02062-9106, U.S.A.
• Tel
• Fax
•

Evaluation Board for 8 lead MSOP devices in the Switch/Mux portfolio
8 lead MSOP evaluation board Clamp to allow the main device to be changed easily Gold pin connectors to allow the addition of passive
components SMB connectors for the input/output of signals Additional space on board to allow for prototyping

EVALUATION KIT CONTENTS

EVAL-8MSOPEBZ evaluation board

ONLINE RESOURCES

Documents Needed Data sheet of the device to be evaluated EVAL-8MSOPEBZ user guide

EQUIPMENT NEEDED

Device to be evaluated DC voltage source Analog signal source Method to measure voltage, such as a digital multimeter DMM

The EVAL-8MSOPEBZ is the evaluation board for the 8 lead MSOP devices in the switch/mux portfolio which are to be purchased separately. A clamp is supplied with the board so that the device can be secured to the board without the need for soldering. This makes the board reusable for multiple devices.

Figure 1 shows the EVAL-8MSOPEBZ evaluation board. The device can be clamped or soldered to the center of the evaluation board. Each pin of the device is broke out to a link that can be set to either VDD or GND and a wire screw terminal is provided to supply VDD and GND. SMB connectors are on the board allow for additional external signals to be supplied to the device. In addition, there is space at the top of the board available for prototyping.

Full specifications of the device under test are available in the product data sheet, which should be consulted in conjunction with this user guide when using the evaluation board.

EVALUATION BOARD

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS.

UG-xxx

TABLE OF CONTENTS
0 Initial Version

Preliminary Technical Data
Power Link SMB Connectors Input Signal Evaluation Board Schematics and Ordering Bill of

Preliminary Technical Data

EVALUATION BOARD HARDWARE

The operation of a 8 lead MSOP devices in the switch/mux portfolio can be evaluated using the EVAL-8MSOPEBZ. Figure 1 shows the evaluation board.

POWER SUPPLY

Connector J5 provides the ability to supply VDD and GND supplies to the board. These can them be selected for each pin of the device by setting the link headers to either VDD or GND. If a VSS supply is needed then the voltage can applied directly to the pin of the device. An example of how this can be done is by removing the link and then supplying the required voltage to the central pin of the header or to the gold pin connectors on the relevant trace.

LINK HEADERS

The link headers are used to supply the device under test with either VDD or GND. Each header is designated K1 to K8, with the number corresponding to the pin number of the device. Table 1 shows a summary of the link headers and how they function on the evaluation board.

Table Link Header Descriptions

Label Position Description

K1to K8 H

UG-xxx

SMB CONNECTORS

They are four SMB connectors on evaluation board labelled J1 to J4. When an SMB cable is one of these connectors, the signal becomes available on either P1 to P4. This signal can then be applied to the pin of the device by forming a connection from either P1 to P4 to a gold pin connector found on the relevant trace.

INPUT SIGNAL TRACES

Each trace includes three sets of gold pin connectors, two of which can be used to place a load on the signal path to ground and another that is in series with the signal path. The three sets of gold pin connectors can be used to create a simple resistorcapacitor RC filter.

UG-xxx EVALUATION BOARD SCHEMATICS AND ARTWORK

Preliminary Technical Data

Figure ADG5208F Evaluation Board Schematic

Figure EVAL-ADG5208FEBZ Silkscreen

Preliminary Technical Data

Figure EVAL-ADG5208FEBZ Bottom Layer

UG-xxx

UG-xxx
ORDERING INFORMATION

BILL OF MATERIALS

Table

Preliminary Technical Data

Preliminary Technical Data NOTES

UG-xxx

ESD Caution ESD electrostatic discharge sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
2015 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners.

UG13456-0-8/15 0

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived EVAL-8MSOPEBZ Datasheet file may be downloaded here without warranties.

Datasheet ID: EVAL-8MSOPEBZ 517898