ADP5350CP-EVALZ User Guide
Part | Datasheet |
---|---|
![]() |
ADP5350CP-EVALZ (pdf) |
PDF Datasheet Preview |
---|
ADP5350CP-EVALZ User Guide UG-1104 One Technology Way t P.O. Box 9106 t Norwood, MA 02062-9106, U.S.A. t Tel t Fax t Evaluating the ADP5350 Battery Management PMIC with Inductive Boost LED and Three LDO Regulators Input voltage V to V Full featured evaluation board for the ADP5350 Evaluation software and installation CD included Simple device measurements and demonstrable with A voltage supply A battery or battery simulator Load resistors or an electrical load EQUIPMENT NEEDED USB to I2C dongle USB-SDP-CABLEZ not included in the evaluation kit and must be ordered separately SOFTWARE NEEDED ADP5350CP-EVALZ graphic user interface GUI software This user guide describes the hardware and software for the evaluation of the ADP5350CP-EVALZ evaluation board, and includes detailed schematics and printed circuit board PCB layouts. The ADP5350 combines one high performance buck regulator for single Li-ion/Li-ion polymer battery charging, a fuel gauge, a highly programmable boost regulator for LED backlight illumination, one ultralow quiescent current low dropout LDO regulator, and two general-purpose LDO regulators. The ADP5350CP-EVALZ evaluation board supports an external USB dongle connection and the GUI software allows the user to evaluate the comprehensive functionalities provided by the I2C interface. The ADP5350 operates over the −40°C to +125°C junction temperature range and is available in a 32-lead, 5 mm x 5 mm LFCSP package. Full details on the device are provided in the ADP5350 data sheet, available from Analog Devices, Inc., which must be consulted in conjunction with this evaluation board user guide. ADP5350CP-EVALZ EVALUATION BOARD 15553-001 Figure PLEASE SEE THE LAST PAGE FOR AN IMPORTANT WARNING AND LEGAL TERMS AND CONDITIONS. UG-1104 TABLE OF CONTENTS Installing LabVIEW 3 Installing the ADP5350 GUI Software 3 Installing the Analog Devices SDP Drivers 4 Using ADP5350 GUI Software 5 Operating the Board with the GUI 5 Basic Charging Parameter Settings 5 Battery SOC 6 LED Lighting, Boost, and LDO Settings 6 0 Initial Version ADP5350CP-EVALZ User Guide Direct Register Write and Fuel Gauge Data GUI Using the Evaluation Board Powering Up the Evaluation Board Evaluation Board Measurements 10 Charge Function Evaluation 10 Fuel Gauge Function Evaluation 10 LED and LDO Function Evaluation 10 Evaluation Board Schematics and Artwork................................ 12 Ordering Information 15 Bill of 15 Related 15 ADP5350CP-EVALZ User Guide INSTALLING THE SOFTWARE The ADP5350CP-EVALZ GUI software allows evaluation of all functions and features of the program registers. Before starting the software installation, ensure that the ADP5350CP-EVALZ evaluation board is not connected to the USB port of the PC. INSTALLING LabVIEW If the PC already has LabVIEW installed, this step is not needed. The application software is a compiled LabVIEW program, which requires LabVIEW or later and a run-time engine installed on the PC. Download the LabVIEW run-time engine from the National Instruments website. A LabVIEW run-time installation is available on the ADP5350CP-EVALZ installation CD. INSTALLING THE ADP5350 GUI SOFTWARE After installation, it may be necessary to reboot the PC to complete the operation. Launch the Setup.exe file. The dialog box shown in Figure 2 appears. UG-1104 Click Next to install the program see Figure Figure Select Program Folder Click Finish to complete the installation see Figure 15553-004 15553-005 Figure ADP5350 Evaluation Software Setup Click Next to install the files to the default destination folder or click to choose a different file see Figure 15553-002 Figure Installation Complete 15553-003 Figure Choose Destination Location UG-1104 INSTALLING THE ANALOG DEVICES SDP DRIVERS To install the Analog Devices system demonstration platform SDP drivers, complete the following steps After installing ADP5350CP-EVALZ GUI software, the installation of the SDP drivers begins. Click Next to install the drivers see Figure ADP5350CP-EVALZ User Guide Click Finish to complete the driver installation see Figure 15553-008 Figure SDP Drivers Setup Wizard Click Install after verifying the destination folder. Ensure that the system environment has enough space see Figure 15553-006 Figure Driver Installation Complete To verify that the USB driver is installed properly, click Start. Then select Control Panel > System and open the Device Manager see Figure 15553-009 Figure Verify the Destination Folder Figure Verify Driver Installation When the USB dongle is connected to a PC port different from the one used to install the driver, the PC device driver may require that the driver be installed again for that specific port. If this occurs, repeat Step 1 through Step ADP5350CP-EVALZ User Guide USING ADP5350 GUI SOFTWARE ORDERING INFORMATION BILL OF MATERIALS Table Qty. Reference Designator 1 U1 4 C1, C4, C5, C7 2 C2, C11 2 C3, C8 2 C6, C10 1 C9 16 D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16 3 D18, D19, D20 1 L1 1 L2 1 R1 3 R4, R6, R7 1 R8 1 R9 1 R10 Description Battery management, power management IC PMIC Capacitor, multilayer ceramic capacitors MLCC , 1 uF 6.3V X5R 0402 Capacitor, MLCC, uF, V, X5R, 0402 Capacitor, MLCC, uF, V, X5R, 0603 Capacitor, MLCC, 10 uF, V, X5R, 0805 Capacitor, MLCC, uF, 25 V, X5R, 0603 LED Manufacturer Analog Devices Murata Murata Lite-On Part Number ADP5350 GRM155R60J105KE19D GRM155R60J225KE95D GRM188R60J475KE19D GRM188R60J106KE47D GRM21BR61E475KA12 LTW-170TK LED Inductor, uH Inductor, uH Variable Resistor, 200 kΩ, 0.5W Resistor, kΩ, 0402 Resistor, 127 kΩ, 0402 Resistor, 10 kΩ, 0402 Resistor, 0 Ω, 0402 Lite-On Wurth Bourns Panasonic LTST-C192KGKT 74479776215 74479776247A 3296W-1-204LF ERJ-2RKF5101X ERJ-2RKF1273X ERJ-2RKF1002X ERJ-2GE0R00X RELATED LINKS Resource ADP5350 Description Advanced Battery Management PMIC with Inductive Boost LED and Three LDO Regulators ESD Caution ESD electrostatic discharge sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality. Legal Terms and Conditions 2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. UG15553-0-2/17 0 |
More datasheets: MBF5A | MBE5C1 | T555714-DBW | T555711-TAS | T555715-PAE | T555711-DDW | T555714-DDW | T555711-DDT | FE077-A/125850 | PCM-3618-AE |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ADP5350CP-EVALZ Datasheet file may be downloaded here without warranties.