832 832 Datasheet

PRODUCT ID 832

Part	Datasheet
832	832 (pdf)

PDF Datasheet Preview
EL Wire 12V Sound Activated Pocket Inverter PRODUCT ID 832 A small, portable inverter for EL wire with an audio input! This inverter has a little microphone and will light the connected EL according to the surrounding audio volume. Makes for an easy reactive project. This inverter requires 12VDC input it works great with our 8xAA battery holder and it can drive meters 7 to 10 feet of our EL wire OR 1 meter 3 feet of EL tape OR a 10cmx10cm piece of EL panel continuously for about 48 hours off of 4xAA's . There is a switch for selecting steady/sound/off modes steady is 'always on'. Comes with a single 2.5mm pitch female JST connectors, standard for all the EL wire and tape we carry. There's also two power wires, you'll need to connect these to a 12VDC power source. The white striped wire goes to +12V, the plain black wire goes to ground. You can plug any of our EL wire/tape into this inverter directly. To connect a 'raw' piece EL wire to this, you'll want a male connector wire The EL inverter requires a 'load' to stabilize itself. Do not run the inverter without at least 2 ft of EL wire attached! Otherwise the inverter can spike and damage itself Like all inverters we've used, the 2000 Hz oscillation is slightly audible. To reduce the squeaking, we suggest opening up the case padding it with thick foam tape/weatherstripping. Squirting some hot glue around the capacitors may also help. We managed to get it silent this way. Check out our EL TRON bag tutorial for ideas, and our EL wire couch video too! Soldering to raw EL wire is a little tricky but luckily we wrote a detailed tutorial! The tutorial also covers a lot of information about EL and how it works. Technical Details Dimensions: o Inverter Size 85mm x 55mm x 22mm 3.4in x 2.2in x 0.85in o JST cable length approx. 20 cm Weight 41.80g 8-8-17

PDF Datasheet Preview

EL Wire 12V Sound Activated Pocket Inverter

PRODUCT ID 832

A small, portable inverter for EL wire with an audio input! This inverter has a little microphone and will light the connected EL according to the surrounding audio volume. Makes for an easy reactive project. This inverter requires 12VDC input it works great with our 8xAA battery holder and it can drive meters 7 to 10 feet of our EL wire OR 1 meter 3 feet of EL tape OR a 10cmx10cm piece of EL panel continuously for about 48 hours off of 4xAA's . There is a switch for selecting steady/sound/off modes steady is 'always on'. Comes with a single 2.5mm pitch female JST connectors, standard for all the EL wire and tape we carry. There's also two power wires, you'll need to connect these to a 12VDC power source. The white striped wire goes to +12V, the plain black wire goes to ground. You can plug any of our EL wire/tape into this inverter directly. To connect a 'raw' piece EL wire to this, you'll want a male connector wire The EL inverter requires a 'load' to stabilize itself. Do not run the inverter without at least 2 ft of EL wire attached! Otherwise the inverter can spike and damage itself Like all inverters we've used, the 2000 Hz oscillation is slightly audible. To reduce the squeaking, we suggest opening up the case padding it with thick foam tape/weatherstripping. Squirting some hot glue around the capacitors may also help. We managed to get it silent this way. Check out our EL TRON bag tutorial for ideas, and our EL wire couch video too!

Soldering to raw EL wire is a little tricky but luckily we wrote a detailed tutorial! The tutorial also covers a lot of information about EL and how it works.

Technical Details

Dimensions:
o Inverter Size 85mm x 55mm x 22mm 3.4in x 2.2in x 0.85in o JST cable length approx. 20 cm

Weight 41.80g
8-8-17

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 832 Datasheet file may be downloaded here without warranties.

832

832 Datasheet

Datasheet ID: 832 514855