ACL 450CPS

ACL 450CPS Datasheet

ACL 450CPS

Part	Datasheet
ACL 450CPS	ACL 450CPS (pdf)

PDF Datasheet Preview
ACL 450CPS Charged Plate System for the ACL 450 Easy to Use: While away from ionized turn the ACL 450 on and check “zero” reading. Slide the plate assembly onto the 450 Select charger polarity by grounding the opposite terminal. Ground “-” to select To charge the plate adapter, place it in contact with the appropriate charger terminal. Position the with the plate adapter in the ionizer The meter should rapidly drop from 1100 V to zero. To test the decay rate, connect the to a chart recorder or use a stopwatch to measure the time required for the voltage to decay from ±1.00kV to ±0.10kV. To check balance, attach plate adapter to and point it into the ionizer Check for an average reading of zero. An reading indicates an unbalanced ionizer. Note All tests should be performed while wearing a wrist strap to ensure proper grounding. Product # ACL 450 includes carrying case, 9-volt battery, and NIST-traceable calibration Product # ACL 450CPS includes charge plate monitor and carrying case. Low cost way to test air ionizer performance Increase the utility of your ACL 450 Electrostatic Fieldmeter for ionized environments by adding the 450CPS Charged Plate System. The 450CPS Charged Plate System will allow the 450 to test and monitor the and balance of air ionization devices. The 450CPS includes a charge plate attachment for the ACL 450 and a charging source to charge the plate attachment. The then measures the plate voltage during balance and decay tests. This low-cost system, designed to meet ESDA Standard DSP3.3 Periodic of Air Ionizers, correlates closely to tests results from table-top charged-plate monitors. Performing both positive and negative decay tests, the HOLD feature on the meter permits balance measurements to be taken in areas inaccessible with standard charged plate monitors. The analog output provides 1 volt output corresponding to a 10kV reading on the display. Plate Assembly Plate Capacitance 12 picofarads ± 2 picofarads Range 0 ± 2 kV Grounding:Connection through ACL 450 conductive case Weight ounces Charger Output 1100 VDC normal, < 1uA max. Output Terminals Two acorn buttons labeled + and To select, ground opposite terminal. Power Supply 9-volt alkaline battery Relative Humidity 10% to 80% non-condensing Temperature Range 10° to 30° C 50° to 86°F Weight ounces Size x cm 840 W. 49th Place • Chicago, IL 60609 • • fax • ACL Inc. registered to ISO-9001 2008 No. 10002746

PDF Datasheet Preview

ACL 450CPS

Charged Plate System for the ACL 450

Easy to Use:

While away from ionized turn the ACL 450 on and check “zero” reading. Slide the plate assembly onto the 450 Select charger polarity by grounding the opposite terminal. Ground “-” to select To charge the plate adapter, place it in contact with the appropriate charger terminal. Position the with the plate adapter in the ionizer The meter should rapidly drop from 1100 V to zero.

To test the decay rate, connect the to a chart recorder or use a stopwatch to measure the time required for the voltage to decay from ±1.00kV to ±0.10kV.

To check balance, attach plate adapter to and point it into the ionizer Check for an average reading of zero. An reading indicates an unbalanced ionizer.

Note All tests should be performed while wearing a wrist strap to ensure proper grounding.

Product # ACL 450 includes carrying case, 9-volt battery, and NIST-traceable calibration

Product # ACL 450CPS includes charge plate monitor and carrying case.

Low cost way to test air ionizer performance

Increase the utility of your ACL 450 Electrostatic Fieldmeter for ionized environments by adding the 450CPS Charged Plate System. The 450CPS Charged Plate System will allow the 450 to test and monitor the and balance of air ionization devices. The 450CPS includes a charge plate attachment for the ACL 450 and a charging source to charge the plate attachment. The then measures the plate voltage during balance and decay tests. This low-cost system, designed to meet ESDA Standard DSP3.3 Periodic of Air Ionizers, correlates closely to tests results from table-top charged-plate monitors.

Performing both positive and negative decay tests, the HOLD feature on the meter permits balance measurements to be taken in areas inaccessible with standard charged plate monitors. The analog output provides 1 volt output corresponding to a 10kV reading on the display.

Plate Assembly

Plate Capacitance 12 picofarads ± 2 picofarads Range 0 ± 2 kV Grounding:Connection through ACL 450 conductive case Weight ounces

Charger

Output 1100 VDC normal, < 1uA max.

Output Terminals Two acorn buttons labeled + and To select, ground opposite terminal.

Power Supply 9-volt alkaline battery

Relative Humidity 10% to 80% non-condensing

Temperature Range 10° to 30° C 50° to 86°F

Weight ounces

Size x cm
840 W. 49th Place
• Chicago, IL 60609
•
• fax
•

ACL Inc. registered to ISO-9001 2008 No. 10002746

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ACL 450CPS Datasheet file may be downloaded here without warranties.

Datasheet ID: ACL 450CPS 522106