81040-U10204
81040-U10204 Datasheet
x Low Profile, Straight, Molded-in Latch 810 Series
| Part | Datasheet |
|---|---|
81040-U10204 |
81040-U10204 (pdf) |
| PDF Datasheet Preview |
|---|
| Pak 50 4-Wall, Tripolarized Header x Low Profile, Straight, Molded-in Latch 810 Series S Tripolarization to mating socket S 50 mil x 100 mil halves the connector length S Molded-in latch for space limited designs S Two-row tail design saves board space S Four-wall shroud provides contact protection S Contacts 40 Date Modified May 25, 2005 TS-0482-11 Sheet 1 of 3 Physical Insulation Material Glass Filled Polyester PBT Flammability UL 94V-0 Color Gray File Replace by consolidated ts file: Contact Material Copper Alloy Plating Underplating 100 [ µm ] Nickel QQ-N-290, Class 2 Wiping Area 30 [ µm ] Gold MIL-G-45204, Type II, Grade C Solder Tails 200 [ µm ] Tin Lead Marking Orientation Triangle and 3M Logo Electrical Current Rating A Insulation Resistance > 1 x 109 at 500 Vdc Withstanding Voltage 500 Vrms at Sea Level Environmental Temperature Rating - 55°C to +105°C UL File No. E68080 Interconnect Solutions 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Pak 50 4-Wall, Tripolarized Header x Low Profile, Straight, Molded-in Latch 810 Series 81XXX Position 2 Position 1 Ref Latches flexed open Position 1 Orientation Triangle Tri-Ribbed Orientation/Retention Post File Replace by consolidated ts file: Tri-Ribbed Post Ordering Information Interconnect Solutions Inch [mm] Tolerance Unless Noted Inch ± ± ± [ ] Dimensions for Reference only Header 81040-U10204 TS-0482--11 Sheet 2 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Pak 50 4-Wall, Tripolarized, Low Profile Header x Low Profile, Straight, Molded-in Latch 810 Series *Solder Thief Solder Pads See Note 2 -- -- -- -- *Solder Thief Solder Pads are required only on Solder side of PC Board. View A See Note 4 2X ± ± Typ Tolerance Noncumulative Flow Solder Direction See Note 1 Position 2 Optional File Replace by consolidated ts file: 2X ± See Note 3 View A Position 1 ± Typ Recommended Mounting Hole Pattern Shown for mounting side of PC Board Notes Recommended to process PC Boards PC Board thickness through the solder bath such that the connector enters end first two solder tails at a time . This will help prevent solder bridging. A Solder Thief Solder Pad Dummy Pad aat the end of each row is recommended on the bottom or solder side of the PC Board in order to help prevent solder bridging on the end solder tails. The Solder Thiefs are only required on the end of the rows which leave the solder bath last. In order to retain the connector on the PC Board during the assembly and soldering process, it is recommended to have a through hole diameter of ± In order to facilitate unmating of the system, it is recommended to use the 3490--2 Pull Tab with the mating X Wiremount Socket. TS-0482-11 Sheet 3 of 3 Interconnect Solutions 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Important Notice All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Electronics 6801 River Place Blvd. Austin, TX 78726-9000 800/328-1368 Warranty Limited Remedy Limited Liability. This product will be free from defects in material and manufacture for a period of one 1 year from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. Minimum 10% Post-Consumer Fiber Printed in USA. 3M 2005 |
| More datasheets: SPB-3902 | SPB-3903 | SPB-3923 | SPB-3904 | SPB-3921 | SPB-3901 | SPB-3922 | 473 | DFR0471 | EIR308 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 81040-U10204 Datasheet file may be downloaded here without warranties.