4320-SSHCTO/15-GBM

4320-SSHCTO/15-GBM Datasheet

4320 SS-25

Part	Datasheet
4320-SSHCTO/15-GBM	4320-SSHCTO/15-GBM (pdf)

Related Parts	Information
4320-SSHCTO/15-GBM(BULK)	4320-SSHCTO/15-GBM(BULK)

PDF Datasheet Preview
4320 SS-25 Self-Strip Terminating Block Instructions May 2002 78-8130-7677-1 General The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for 22- mm and 24-gauge mm jumper wire. The self-strip caps automatically connect and trim the jumper wire with a 90° turn of the cap. The 4320 Blocks are dimensionally compatible with all pedestal and pole-mount cabinets used in the 3M 4310 Modular Hardwire System. Note White 4320 SS-25 Self-Strip Terminating Blocks are intended for use in OSP Outside Plant applications only, mounted in OSP pedestal or polemount cross-connect cabinets. Grey blocks are intended for indoor use, on the equipment side of a primary telephone protector. Accessories 4320 SS-25 Self-Strip Terminating Block 4327 Single Pair Probe 4324 SS Priority Cap 4327-A Probe and Dish 4327P Pocket Probe 4328 SS 25 Pair Test Connector 78-8130-7677-1 Running Jumper Wires Pull 24 AWG mm or 22 AWG mm jumper wire from spool to feeder block. Green labels on tabs. Split pair TIP-left, RING-right at the assigned cap position. Note Wire ends should not be stripped. Form 90° hook on end of jumper wire as shown. Make sure wires have cleanly-cut ends. Insert screwdriver in cap slot and rotate 90° clockwise until you feel the cap come to rest against the stop. As the cap rotates, the wire is simultaneously connected and trimmed off. Note Make sure screwdriver blade is fully inserted into cap slot before rotating. Unconnected Position Make sure assigned caps are in the preinsertion position with the screwdriver slot oriented vertically. Screwdriver Slot Entry Port Exit Port Connected Position Always route jumper wires below the connected cap. Pair 1 orange Preinsertion Cap Position Insert wire into entry port and through the cap until the wire is visible from the exit port. 2" 50 mm Slack Loop Pair 21 Pair 5 78-8130-7677-1 Pair 25 2" 50 mm Slack Loop Lay jumper wires into runway between self-strip caps. Push the jumpers down into the runway below the connection ports. Connection Ports

PDF Datasheet Preview

4320 SS-25

Self-Strip Terminating Block

Instructions

May 2002 78-8130-7677-1

General

The 3M 4320 SS-25 Self-Strip Terminating Block is a factory stubbed, self-stripping connecting block designed for 22- mm and 24-gauge mm jumper wire. The self-strip caps automatically connect and trim the jumper wire with a 90° turn of the cap. The 4320 Blocks are dimensionally compatible with all pedestal and pole-mount cabinets used in the 3M 4310 Modular Hardwire System.

Note White 4320 SS-25 Self-Strip Terminating Blocks are intended for use in OSP Outside Plant applications only, mounted in OSP pedestal or polemount cross-connect cabinets. Grey blocks are intended for indoor use, on the equipment side of a primary telephone protector.

Accessories
4320 SS-25 Self-Strip Terminating Block
4327 Single Pair Probe
4324 SS Priority Cap
4327-A Probe and Dish
4327P Pocket Probe
4328 SS 25 Pair Test Connector
78-8130-7677-1

Running Jumper Wires

Pull 24 AWG mm or 22 AWG mm jumper wire from spool to feeder block. Green labels on tabs.

Split pair TIP-left, RING-right at the assigned cap position.

Note Wire ends should not be stripped.

Form 90° hook on end of jumper wire as shown. Make sure wires have cleanly-cut ends.

Insert screwdriver in cap slot and rotate 90° clockwise until you feel the cap come to rest against the stop. As the cap rotates, the wire is simultaneously connected and trimmed off.

Note Make sure screwdriver blade is fully inserted into cap slot before rotating.

Unconnected Position

Make sure assigned caps are in the preinsertion position with the screwdriver slot oriented vertically.

Screwdriver Slot

Entry Port

Exit Port

Connected Position

Always route jumper wires below the connected cap.

Pair 1
orange

Preinsertion Cap Position

Insert wire into entry port and through the cap until the wire is visible from the exit port.
2" 50 mm Slack Loop

Pair 21 Pair 5
78-8130-7677-1

Pair 25
2" 50 mm

Slack Loop

Lay jumper wires into runway between self-strip caps. Push the jumpers down into the runway below the connection ports.

Connection Ports

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 4320-SSHCTO/15-GBM Datasheet file may be downloaded here without warranties.

Datasheet ID: 4320-SSHCTO/15-GBM 518021