SPH-1200-24G

SPH-1200-24G Datasheet

SPH-1200, Power Factor Corrected Single Output, Hot Swap

Part	Datasheet
SPH-1200-24G	SPH-1200-24G (pdf)

Related Parts	Information
SPH-1200-48G	SPH-1200-48G

PDF Datasheet Preview
SPH-1200, Power Factor Corrected Single Output, Hot Swap FEATURES: • Diode isolated output for hot swap • “Zero wire” slope program current sharing for redundancy • High power density 5 W/cu. in. • Industry standard DIN connector • Universal ac input • typical power factor • Dc power good and ac power fail signals • True remote inhibit • Monotonic turn-on and turn-off The SPH-1200 series provides low cost, highly reliable, N+1 redundant hot swap power for critical applications. SPECIFICATIONS: INPUT Ac Input 105-264 Vac continuous range, 47 to 63 Hz. Internally fused for 20 A. Power Factor typical at full load. Meets EN61000-3-2 Class A. Inrush Cold start ac current is less than 75 A at 115 Vac and 150 A at 230 Vac for 8 ms typical. Limited by thermistor. Holdup Time 16 ms minimum after removal of power at full load. Efficiency 80% minimum Ac Power Fail Provides TTL “0” 5 ms before output voltage goes out of regulation band upon loss of ac power. Brownout Protection Holds regulation to 85 Vac for 30 seconds maximum. OUTPUT Adjustability User adjustable ±5% minimum. Line Regulation Load Regulation ±2% Slope Program from 0 to 100% load change. Turn On Delay 1 second typical Output Rise Time from 10% to 90% 20 ms typical. Ripple & Noise Less than 1% p-p, measured at 20 MHz bandwidth. Temperature Coefficient per degree C. Stability over 8 hours after 30 minutes warm-up. Transient Response Output voltage returns to within 1% in less than 500 µs for a 50% load change. Peak transient does not exceed Overload Protection Electronic current limit, 120% maximum. Overvoltage Protection Protects load against power supply induced overvoltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. Requires ac input to be cycled to reset. Remote Inhibit Contact closure or a TTL level “0” turns off dc output. Dc Power Good Provides a TTL “0” open collector when output is above 90% of nominal. Maximum pull-up voltage 30 Vdc maximum sink current, 10 mA. Redundancy Built-in OR-ing diode, slope program current sharing, and DIN blade connector provide “hot swap” and “N+1” capabilities. Current sharing remains within 10% of the unit’s full output rating given initial accuracy in the output voltage setting. Status Indicators Green LED on the front panel indicates normal operation ACPF high and DCPG low ENVIRONMENTAL Thermal Protection Shuts down power supply if overheated. Automatic recovery. Temperature Range 0° to 50°C at full ratings. Safety Agencies Approved to UL1950 CSA #950 IEC 950 and TÜV EN60950, Class 1 SELV, CE 73/23/EEC//93/68/EEC low voltage directive . Conducted RFI Meets FCC Part 15, Class A EN55022 Class B. Cooling Self-cooled by internal ball-bearing fan. OPTIONS Option “R”, Rack Mount Panel Special panel is required for rack mounting. AC INPUT 105-264 VAC Continuous Range LOCATION 115 VAC 230 VAC CONNECTOR Line Line 1 See Below Neutral Line 2 Safety Ground Safety Ground DC OUTPUT FUNCTION LOCATION NOTES Output Voltage Z12 D14 Z16 D18 + to Polarity Z4 D6 Z8 D10 - to Polarity CONNECTOR Eurocard connector-male DIN 41 612 Level 1-type H STATUS AND CONTROL FUNCTION LOCATION Dc Power Good Z20 Ac Power Fail D22 Inhibit NOTES Reference to common CONNECTOR See Above Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033 800-235-5929 • 805-486-4565 • FAX 805-487-8911 • SPH-1200, Power Factor Corrected Single Output, Hot Swap Commercial Model SPH-1200-24 SPH-1200-28 SPH-1200-48 Power Out 1200 Output No. 1

PDF Datasheet Preview

SPH-1200, Power Factor Corrected Single Output, Hot Swap

FEATURES:
• Diode isolated output for hot swap
• “Zero wire” slope program current sharing for redundancy
• High power density 5 W/cu. in.
• Industry standard DIN connector
• Universal ac input
• typical power factor
• Dc power good and ac power fail signals
• True remote inhibit
• Monotonic turn-on and turn-off The SPH-1200 series
provides low cost, highly reliable, N+1 redundant hot swap power for critical applications.

SPECIFICATIONS:

INPUT Ac Input 105-264 Vac continuous range, 47 to 63 Hz. Internally fused for 20 A. Power Factor typical at full load. Meets EN61000-3-2 Class A. Inrush Cold start ac current is less than 75 A at 115 Vac and 150 A at 230 Vac for 8 ms typical. Limited by thermistor. Holdup Time 16 ms minimum after removal of power at full load. Efficiency 80% minimum Ac Power Fail Provides TTL “0” 5 ms before output voltage goes out of regulation band upon loss of ac power. Brownout Protection Holds regulation to 85 Vac for 30 seconds maximum. OUTPUT Adjustability User adjustable ±5% minimum. Line Regulation Load Regulation ±2% Slope Program from 0 to 100% load change. Turn On Delay 1 second typical Output Rise Time from 10% to 90% 20 ms typical. Ripple & Noise Less than 1% p-p, measured at 20 MHz bandwidth. Temperature Coefficient per degree C. Stability over 8 hours after 30 minutes warm-up. Transient Response Output voltage returns to within 1% in less than 500 µs for a 50% load change. Peak transient does not exceed Overload Protection Electronic current limit, 120% maximum. Overvoltage Protection Protects load against power supply induced overvoltage. Trip point is factory set so that output voltage cannot exceed 136% of nominal. Requires ac input to be cycled to reset. Remote Inhibit Contact closure or a TTL level “0” turns off dc output. Dc Power Good Provides a TTL “0” open collector when output is above 90% of nominal. Maximum pull-up voltage 30 Vdc maximum sink current, 10 mA. Redundancy Built-in OR-ing diode, slope program current sharing, and DIN blade connector provide “hot swap” and “N+1” capabilities. Current sharing remains within 10% of the unit’s full output rating given initial accuracy in the output voltage setting.

Status Indicators Green LED on the front panel indicates normal operation ACPF high and DCPG low ENVIRONMENTAL Thermal Protection Shuts down power supply if overheated. Automatic recovery. Temperature Range 0° to 50°C at full ratings. Safety Agencies Approved to UL1950 CSA #950 IEC 950 and TÜV EN60950, Class 1 SELV, CE 73/23/EEC//93/68/EEC low voltage directive . Conducted RFI Meets FCC Part 15, Class A EN55022 Class B. Cooling Self-cooled by internal ball-bearing fan.

OPTIONS Option “R”, Rack Mount Panel Special panel is required for rack mounting.

AC INPUT 105-264 VAC Continuous Range

LOCATION
115 VAC
230 VAC

CONNECTOR

Line

Line 1

See Below

Neutral

Line 2

Safety Ground Safety Ground

DC OUTPUT

FUNCTION

LOCATION

NOTES

Output Voltage Z12 D14 Z16 D18 + to Polarity

Z4 D6 Z8 D10
- to Polarity

CONNECTOR Eurocard connector-male DIN 41 612 Level 1-type H

STATUS AND CONTROL

FUNCTION

LOCATION

Dc Power Good Z20

Ac Power Fail D22

Inhibit

NOTES Reference to common

CONNECTOR See Above

Condor D.C. Power Supplies, Inc., 2311 Statham Parkway, Oxnard, CA 93033
800-235-5929
• 805-486-4565
• FAX 805-487-8911
•

SPH-1200, Power Factor Corrected Single Output, Hot Swap

Commercial Model SPH-1200-24 SPH-1200-28 SPH-1200-48

Power Out 1200

Output No. 1

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived SPH-1200-24G Datasheet file may be downloaded here without warranties.

Datasheet ID: SPH-1200-24G 506481