DKBLE112

DKBLE112 Datasheet


DKBLE112 operates as USB bus powered device. UART and USB interface share the same USB connector. To use the USB interface, turn SW13 to USB position.

Part Datasheet
DKBLE112 DKBLE112 DKBLE112 (pdf)
PDF Datasheet Preview
BLE112 DEVELOPMENT KIT

DATASHEET

Monday, 24 February 2014 Version

Copyright 2000-2014 Bluegiga Technologies

All rights reserved. Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual. Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications detailed here at any time without notice and does not make any commitment to update the information contained here. Bluegiga’s products are not authorized for use as critical components in life support devices or systems. The WRAP is a registered trademark of Bluegiga Technologies The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies. All other trademarks listed herein are owned by their respective owners.

Bluegiga Technologies Oy

VERSION HISTORY Version

Comment

Figure 2 added Chapter Using the Analog Comparator of BLE112 added Release

Bluegiga Technologies Oy

TABLE OF CONTENTS
1 Design Overview Sensors, display and USB to UART converter
2 Interfaces Powering the Development Board On-Board Debugger Using the On-Board Debugger to Update the FW of the Embedded BLE112 Module Using the On-Board Debugger to Update External Devices Indicator LED UART Display and Pin Header and Using the Analog Comparator of BLE112
3 Measuring Current Consumption 10 4 Schematics And Assembly 11 5 WEEE Compliance 18 6 Contact Information 19

Bluegiga Technologies Oy
1 Design Overview

BLE112 Development Kit is targeted for engineers evaluating BLE112 Bluetooth single mode modules and developing or prototyping Bluetooth systems utilizing BLE112 module s . BLE112 Development Kit features:

Evaluation board for BLE112 module containing o On-Board debugger o Switchable powering either from a coin cell battery or USB o Switchable USB or UART interface through USB to UART converter o programming interface for upgrading the firmware and parameters o Display connected to SPI o Accelerometer connected to SPI o Potentiometer for ADC input o Push buttons for 4 PIOs and reset o All the PIOs available at a pin header o Current measurement points for measuring peak currents of the module, DC current of the module and DC current of the whole board.

Battery

DC/DC

Power USB/BAT

Select USB/UART interface

USB to UART

Converter

R BLE112

Current test point Buttons

OFF ON OFF ON

OFF ON

MOD EXT

Display

Accelerometer

DEBUGGER Rpot

Figure 1 Block diagram of BLE112 evaluation board Bluegiga Technologies Oy

Page 5 of 19

Please, refer to the latest BLE112 data sheet for information about BLE112 Bluetooth single mode module. The physical outlook, schematics, assembly and the PIN configurations of the interfaces of BLE112 Development Kit are described in this document.

Figure 2 BLE112 Development Kit

Sensors, display and USB to UART converter
• Display o Manufacturer Newhaven Display Intl o Manufacturer part number NHD-C0216CZ-FSW-FBW-3V3 o Datasheet:
• Altimeter U6 o Manufacturer Analog Devices o Manufacturer part number ADXL350BCEZ-RL o

Bluegiga Technologies Oy

Page 6 of 19
More datasheets: EG1390B | CTED-A5B3-622.08TS | CTED-A5B3-212.5TS | CTED-A5B3-155.52TS | CTED-A5B3-156.25TS | CTED-A5B3-311.04TS | 4204-004LF | 4204-004 | TR100 | ACC013


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived DKBLE112 Datasheet file may be downloaded here without warranties.

Datasheet ID: DKBLE112 521933