QVE00033

QVE00033 Datasheet

QVE00033 Phototransistor Optical Surface Mount Interrupter Switch

Part	Datasheet
QVE00033	QVE00033 (pdf)

PDF Datasheet Preview
QVE00033 Phototransistor Optical Surface Mount Interrupter Switch January 2008 QVE00033 Phototransistor Optical Surface Mount Interrupter Switch • No contact switching • Transistor Output • Compact surface mount package • Opaque black plastic housing • 2mm wide slot • mm aperture width • Tape and reel • Reflow conditions: Preheat = 160°C for 120 seconds Reflow = 200°C for 60 seconds peak = 240°C • HL-94V-0 housing The QVE00033 is a miniature slotted optical switch designed for surface mount applications. It consists of a GaAs LED and a silicon phototransistor facing each other across a 2mm gap, and packaged in a temperature resistant black plastic housing. Package Dimension SECTION "A-A" DIMPLE RIGHT VIEW 4X ANODE COLLECTOR CATHODE EMITTER BOTTOM VIEW Note Dimensions for all drawings are in inches millimeters . Tolerance 0.127mm unless othewise specified. QVE00033 Phototransistor Optical Surface Mount Interrupter Switch Absolute Maximum Ratings TA = 25°C unless otherwise specified Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Parameter TOPR TSTG TSOL-I TSOL-F P TOT EMITTER IF VR PD SENSOR VCEO VECO IC PD Operating Temperature Storage Temperature Soldering Temperature Iron 2,3,4 Soldering Temperature Flow 2,3 Total Power Dissipation Collector-Emitter Voltage Emitter-Collector Voltage Collector Current Power Dissipation 1 Notes Derate power dissipation linearly 1.00mW/°C above 25°C. RMA flux is recommended. Methanol or isopropyl alcohols are recommended as cleaning agents. Soldering iron tip 1/16" 1.6mm from housing. Rating -55 to +100 -55 to +100 240 for 5 sec. 260 for 10 sec. 50 6 75 30 20 75 Units °C °C °C °C mW mA V mW V mA mW Electrical/Optical Characteristics TA = 25°C unless otherwise Symbol Parameter Test Conditions Min. Typ. EMITTER Forward Voltage IF = 20mA VR = 4V Peak Emission Wavelength IF = 20mA SENSOR

PDF Datasheet Preview

QVE00033 Phototransistor Optical Surface Mount Interrupter Switch

January 2008

QVE00033 Phototransistor Optical Surface Mount Interrupter Switch
• No contact switching
• Transistor Output
• Compact surface mount package
• Opaque black plastic housing
• 2mm wide slot
• mm aperture width
• Tape and reel
• Reflow conditions:

Preheat = 160°C for 120 seconds Reflow = 200°C for 60 seconds peak = 240°C
• HL-94V-0 housing

The QVE00033 is a miniature slotted optical switch designed for surface mount applications. It consists of a GaAs LED and a silicon phototransistor facing each other across a 2mm gap, and packaged in a temperature resistant black plastic housing.

Package Dimension

SECTION "A-A"

DIMPLE

RIGHT VIEW
4X ANODE

COLLECTOR

CATHODE

EMITTER

BOTTOM VIEW

Note Dimensions for all drawings are in inches millimeters . Tolerance 0.127mm unless othewise specified.

QVE00033 Phototransistor Optical Surface Mount Interrupter Switch

Absolute Maximum Ratings TA = 25°C unless otherwise specified

Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only.

Parameter

TOPR TSTG TSOL-I TSOL-F P TOT EMITTER

IF VR PD SENSOR VCEO VECO IC PD

Operating Temperature Storage Temperature Soldering Temperature Iron 2,3,4 Soldering Temperature Flow 2,3 Total Power Dissipation

Collector-Emitter Voltage Emitter-Collector Voltage Collector Current Power Dissipation 1

Notes Derate power dissipation linearly 1.00mW/°C above 25°C. RMA flux is recommended. Methanol or isopropyl alcohols are recommended as cleaning agents. Soldering iron tip 1/16" 1.6mm from housing.

Rating -55 to +100 -55 to +100 240 for 5 sec. 260 for 10 sec.
50 6 75
30 20 75

Units °C °C °C °C mW
mA V mW

V mA mW

Electrical/Optical Characteristics TA = 25°C unless otherwise

Symbol Parameter

Test Conditions

Min. Typ.

EMITTER

Forward Voltage

IF = 20mA

VR = 4V

Peak Emission Wavelength IF = 20mA

SENSOR

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived QVE00033 Datasheet file may be downloaded here without warranties.

Datasheet ID: QVE00033 634546