FAN4800IN

FAN4800IN Datasheet


FAN4800 Low Start-Up Current PFC/PWM Controller Combos

Part Datasheet
FAN4800IN FAN4800IN FAN4800IN (pdf)
Related Parts Information
FAN4800IMX FAN4800IMX FAN4800IMX
FAN4800IM FAN4800IM FAN4800IM
PDF Datasheet Preview
FAN4800 Low Start-Up Current PFC/PWM Controller Combos

November 2006

FAN4800 Low Start-Up Current PFC/PWM Controller Combos
- Low start-up current 100µA typical - Low operating current 2.5mA typical - Low total harmonic distortion, high power factor - Pin-compatible upgrade for the ML4800 - Average current, continuous or discontinuous boost,
leading-edge PFC - Slew rate enhanced transconductance error amplifier
for ultra-fast PFC response - Internally synchronized leading edge PFC and trailing-
edge PWM - Reduction of ripple current in the storage capacitor
between the PFC and PWM sections - PWM configurable for current-mode or voltage-mode
operation - Additional folded-back current limit for PWM section - 20V BiCMOS process - VIN OK guaranteed turn-on PWM at 2.25V - VCC OVP comparator, low-power detect comparator - Current-fed gain modulator for improved noise
immunity - Brownout control, over-voltage protection, UVLO,
soft-start, and reference OK - Available in 16-DIP, 16-SOIC wide packages
- Desktop PC Power Supply - Internet Server Power Supply - Uninterruptible Power Supply UPS - Battery Charger - DC Motor Power Supply - Monitor Power Supply - Telecom System Power Supply - Distributed Power

The FAN4800 is a controller for power-factor-corrected, switched-mode power supplies. Power Factor Correction PFC allows the use of smaller, lower-cost bulk capacitors, reduces power line loading and stress on the switching FETs, and results in a power supply that fully complies with IEC-1000-3-2 specifications. Intended as a BiCMOS version of the industry-standard ML4800, the FAN4800 includes circuits for the implementation of leading edge, average current, boost-type power factor correction, and a trailing-edge Pulse Width Modulator PWM . A gate driver with 1A capabilities minimizes the need for external driver circuits. Low-power requirements improve efficiency and reduce component costs.

An over-voltage comparator shuts down the PFC section in the event of a sudden decrease in load. The PFC section also includes peak current limiting and input voltage brownout protection. The PWM section can be operated in current or voltage mode, at up to 250kHz, and includes an accurate 50% duty cycle limit to prevent transformer saturation.

The FAN4800 includes a folded-back current limit for the PWM section to provide short-circuit protection.
16-PDIP
16-SOIC
Ordering Information

Part Number FAN4800IN FAN4800IM FAN4800IMX

Operating Temp. Range -40°C to +125°C -40°C to +125°C -40°C to +125°C

Pb-Free Yes

Package 16-PDIP 16-SOIC 16-SOIC

Packing Method

Rail Tape & Reell

Marking Code

FAN4800

FAN4800 Low Start-Up Current PFC/PWM Controller Combos

Block Diagram
16 VEAO
15 VFB 2.5V
0.3V
2 IAC 4 VRMS 3 ISENSE

RAMP1 7

GAIN MODULATOR
1 IEAO

Low Power Detector
3.5k

POWER FACTOR CORRECTOR

VCC 17.9V

VCC OVP 2.78V

TRI-FAULT

PFC OVP
0.5V -1V
3.5k

PFC CMP

PFC ILIMIT

OSCILLATOR
13 VCC
7.5V REFERENCE

VREF 14

PFC OUT 12
8 RAMP2
6 VDC
0.9V
20uA

VREF 9 DC ILIMIT

PWM CMP

DUTY CYCLE LIMIT
More datasheets: 61-GRAY-3/8"X36YD | 26700-210 | MW155RA1251F01 | MW155RA1551F01 | MW155RA1851F01 | M4520 SL001 | M4520 SL002 | M4520 SL005 | ADV7181CBCPZ | ADV7181CBCPZ-REEL


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived FAN4800IN Datasheet file may be downloaded here without warranties.

Datasheet ID: FAN4800IN 513893