EVB9S12NE64

EVB9S12NE64 Datasheet

EVB9S12NE64

Part	Datasheet
EVB9S12NE64	EVB9S12NE64 (pdf)

PDF Datasheet Preview
EVB9S12NE64 Development Board for the M9S12NE64 ! Axiom Manufacturing • 2813 Industrial Lane • Garland, TX 75041 Email Web ! EVB9S12NE64 CONTENTS 05/24/04 CAUTIONARY NOTES TERMINOLOGY FEATURES 4 GETTING SPECIAL OPERATING NOTES REFERENCE DOCUMENTATION EVB9S12NE64 STARTUP MONITOR OPERATION MONITOR MEMORY MAP RUN / LOAD SWITCH EVB9S12NE64 OPERATION MODE MODA, MODB, MODC ROM_OFF 7 MODE_CHART POWER SUPPLY FUSE Power Jack PWR_SW ON/OFF VRH_EN and VRL_EN RESET OPERATION OSC_SEL X1 CLOCK OSCILLATOR EXTERNAL BUS CONFIG J1 ETHERNET PORT STATUS Indicators COM FLOW_SEL Options COM1 COM2 IRDA Port and LCD PORT1 AND 2 I2C EEPROM MEMORY KEYPAD USER COMPONENTS USER_ENABLE 15 USER_IO Connector RV1 User Potentiometer SW1 SW4 Push LED1 4 Indicators M9S12NE64 PORT CONNECTORS MCU1_PORT 17 MCU2_GP BDM TROUBLESHOOTING EVB9S12NE64 05/24/04 TABLE 1 LCD COMMAND AND CHARACTER Cautionary Notes 1 Electrostatic Discharge ESD prevention measures should be applied whenever handling this product. ESD damage is not a warranty repair item. 2 Axiom Manufacturing reserves the right to make changes without further notice to any products to improve reliability, function or design. Axiom Manufacturing does not assume any liability arising out of the application or use of any product or circuit described herein neither does it convey any license under patent rights or the rights of others. 3 EMC Information on the EVB9S12NE64 board: a This product as shipped from the factory with associated power supplies and cables, has been tested and meets with requirements of CE and the FCC as a CLASS A product. b This product is designed and intended for use as a development platform for hardware or software in an educational or professional laboratory. c In a domestic environment this product may cause radio interference in which case the user may be required to take adequate prevention measures. d Attaching additional wiring to this product or modifying the products operation from the factory default as shipped may effect its performance and also cause interference with other apparatus in the immediate vicinity. If such interference is detected, suitable mitigating measures should be taken. Terminology This development board applies option selection jumpers. Terminology for application of the option jumpers is as follows: Jumper on, in, or installed = jumper is a plastic shunt that fits across 2 pins and the shunt is installed so that the 2 pins are connected with the shunt. Jumper off, out, or idle = jumper or shunt is installed so that only 1 pin holds the shunt, no 2 pins are connected, or jumper is removed. It is recommended that the jumpers be idled by installing on 1 pin so they will not be lost. This development board applies hardwired option selections VRL_EN and CUTAWAY 1 These option selections apply a circuit trace between the option pads to complete a default connection. This type connection places an equivalent Jumper Installed type option. The circuit trace between the option pads maybe cut with a razor blade or similar type knife to isolate the default connection provided. Applying the default connection again can be performed by installing the option post pins and shunt jumper, or by applying a wire between the option pads. EVB9S12NE64 05/24/04 The EVB9S12NE64 is an evaluation or development board for the Motorola M9S12NE64 microcontroller. Development of applications is quick and easy with the included DB9 serial cable, sample software tools, examples, and debug monitor. The prototyping area provides space to apply the CPU I/O to your needs. The BDM port is provided for development tool application and is compatible with HCS12 BDM interface cables and software.

PDF Datasheet Preview

EVB9S12NE64

Development Board for the M9S12NE64
! Axiom Manufacturing
• 2813 Industrial Lane
• Garland, TX 75041 Email Web !

EVB9S12NE64

CONTENTS
05/24/04

CAUTIONARY NOTES

TERMINOLOGY

FEATURES 4

GETTING

SPECIAL OPERATING NOTES REFERENCE DOCUMENTATION EVB9S12NE64 STARTUP

MONITOR OPERATION

MONITOR MEMORY MAP RUN / LOAD SWITCH

EVB9S12NE64 OPERATION

MODE MODA, MODB, MODC ROM_OFF 7 MODE_CHART

POWER SUPPLY FUSE Power Jack PWR_SW ON/OFF VRH_EN and VRL_EN

RESET OPERATION OSC_SEL X1 CLOCK OSCILLATOR EXTERNAL BUS CONFIG J1 ETHERNET PORT

STATUS Indicators COM

FLOW_SEL Options COM1 COM2 IRDA Port and LCD PORT1 AND 2 I2C EEPROM MEMORY KEYPAD USER COMPONENTS USER_ENABLE 15 USER_IO Connector RV1 User Potentiometer SW1 SW4 Push LED1 4 Indicators

M9S12NE64 PORT CONNECTORS

MCU1_PORT 17 MCU2_GP BDM

TROUBLESHOOTING

EVB9S12NE64
05/24/04

TABLE 1 LCD COMMAND AND CHARACTER

Cautionary Notes
1 Electrostatic Discharge ESD prevention measures should be applied whenever handling this product. ESD damage is not a warranty repair item.
2 Axiom Manufacturing reserves the right to make changes without further notice to any products to improve reliability, function or design. Axiom Manufacturing does not assume any liability arising out of the application or use of any product or circuit described herein neither does it convey any license under patent rights or the rights of others.
3 EMC Information on the EVB9S12NE64 board:
a This product as shipped from the factory with associated power supplies and cables, has been tested and meets with requirements of CE and the FCC as a CLASS A product.
b This product is designed and intended for use as a development platform for hardware or software in an educational or professional laboratory.
c In a domestic environment this product may cause radio interference in which case the user may be required to take adequate prevention measures.
d Attaching additional wiring to this product or modifying the products operation from the factory default as shipped may effect its performance and also cause interference with other apparatus in the immediate vicinity. If such interference is detected, suitable mitigating measures should be taken.

Terminology

This development board applies option selection jumpers. Terminology for application of the option jumpers is as follows:

Jumper on, in, or installed = jumper is a plastic shunt that fits across 2 pins and the shunt is installed so that the 2 pins are connected with the shunt.

Jumper off, out, or idle = jumper or shunt is installed so that only 1 pin holds the shunt, no 2 pins are connected, or jumper is removed. It is recommended that the jumpers be idled by installing on 1 pin so they will not be lost.

This development board applies hardwired option selections VRL_EN and CUTAWAY 1 These option selections apply a circuit trace between the option pads to complete a default connection. This type connection places an equivalent Jumper Installed type option. The circuit trace between the option pads maybe cut with a razor blade or similar type knife to isolate the default connection provided. Applying the default connection again can be performed by installing the option post pins and shunt jumper, or by applying a wire between the option pads.

EVB9S12NE64
05/24/04

The EVB9S12NE64 is an evaluation or development board for the Motorola M9S12NE64 microcontroller. Development of applications is quick and easy with the included DB9 serial cable, sample software tools, examples, and debug monitor. The prototyping area provides space to apply the CPU I/O to your needs. The BDM port is provided for development tool application and is compatible with HCS12 BDM interface cables and software.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived EVB9S12NE64 Datasheet file may be downloaded here without warranties.

Datasheet ID: EVB9S12NE64 635409