MPQ2560DQ-LF-Z

MPQ2560DQ-LF-Z Datasheet

The MPQ2560 is a high frequency step-down switching regulator with an integrated internal high-side high voltage power MOSFET. It provides 2.5A output with current mode control for fast loop response and easy compensation.

Part	Datasheet
MPQ2560DQ-LF-Z	MPQ2560DQ-LF-Z (pdf)

Related Parts	Information
MPQ2560DQ-LF-P	MPQ2560DQ-LF-P
MPQ2560DN-LF	MPQ2560DN-LF
MPQ2560DN-LF-Z	MPQ2560DN-LF-Z

PDF Datasheet Preview
The Future of Analog IC Technology The MPQ2560 is a high frequency step-down switching regulator with an integrated internal high-side high voltage power MOSFET. It provides 2.5A output with current mode control for fast loop response and easy compensation. The wide 4.5V to 42V input range accommodates a variety of step-down applications, including those in an automotive input environment. A 12uA shutdown mode quiescent current allows use in battery-powered applications. High power conversion efficiency over a wide load range is achieved by scaling down the switching frequency at light load condition to reduce the switching and gate driving losses. The frequency foldback helps prevent inductor current runaway during startup and thermal shutdown provides reliable, fault tolerant operation. By switching at 4MHz, the MPQ2560 is able to prevent EMI Electromagnetic Interference noise problems, such as those found in AM radio and ADSL applications. The MPQ2560 is available in small 3mm x 3mm QFN10 and thermally enhanced SOIC8 packages. MPQ2560 Industrial Grade 2.5A, 4MHz, 42V Step-Down Converter x Guaranteed Industrial Temp Range Limits x Quiescent Current x Wide 4.5V to 42V Operating Input Range x 220m Internal Power MOSFET x Up to 4MHz Programmable Switching Frequency x Stable with Ceramic Capacitor x Internal Soft-Start x Internally Set Current Limit without external Current Sensing Resistor x Up to 93% Efficiency x Output Adjustable from 0.8V to 39V x Available in 3x3 QFN10 and Thermally Enhanced SOIC8 Packages x Industrial Power Systems x High Voltage Power Conversion x Automotive Systems x Distributed Power Systems x Battery Powered Systems “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. 11/19/2009 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 2009 MPS. All Rights Reserved. This datasheet has been downloaded from at this page GRADE, 2.5A, 4MHz, 42V, STEP-DOWN CONVERTER 8,9 VIN SW 1,2 MPQ2560 7 FREQ COMP 4 GND 6 VOUT 3.3V EFFICIENCY % Efficiency vs. Load Current VIN=12V VIN=8V VIN=24V VIN=36V VOUT=3.3V fs=500kHz 50 0 1 2 LOAD CURRENT A MPQ2560 INDUSTRIAL GRADE, 2.5A, 4MHz, 42V STEP-DOWN CONVERTER Part Number* MPQ2560DQ MPQ2560DN ORDERING INFORMATION Package 3x3 QFN10 SOIC8E Top Marking S8 MP2560DN Ambient Temperature to +85qC For Tape & Reel, add suffix eg. For RoHS Compliant Packaging, add suffix eg. * For Tape & Reel, add suffix eg. For RoHS Compliant Packaging, add suffix eg. PACKAGE REFERENCE TOP VIEW TOP VIEW SW 1 SW 2 EN 3 COMP 4 FB 5 EXPOSED PAD ON BACKSIDE CONNECT TO GND 10 BST 9 VIN 8 VIN 7 FREQ 6 GND SW 1 EN 2 COMP 3 FB 4 8 BST 7 VIN 6 FREQ 5 GND EXPOSED PAD CONNECT TO GND ABSOLUTE MAXIMUM RATINGS 1 Supply Voltage to +45V Switch Voltage VSW -7V for < 10ns to VIN + 0.3V BST to SW to +6V All Other Pins to +6V Continuous Power TA = +25°C 3x3 QFN10 2.5W SOIC8 2.5W Junction Temperature ...............................150qC Lead Temperature Storage Temperature.............. to +150qC Recommended Operating Conditions 3 Supply Voltage VIN ...........................4.5V to 42V Output Voltage VOUT.........................0.8V to 39V Operating Junction to +125qC Thermal Resistance 4 3x3 QFN10 50 qC/W SOIC8 Exposed Pad 50 qC/W Notes 1 Exceeding these ratings may damage the device. 2 The maximum allowable power dissipation is a function of the maximum junction temperature TJ MAX , the junction-toambient thermal resistance and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD MAX = TJ Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3 The device is not guaranteed to function outside of its operating conditions. 4 Measured on JESD51-7 4-layer board. 11/19/2009 MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited. 2009 MPS. All Rights Reserved. MPQ2560 INDUSTRIAL GRADE, 2.5A, 4MHz, 42V STEP-DOWN CONVERTER ELECTRICAL CHARACTERISTICS VIN = 12V, VEN = 2.5V, VCOMP = 1.4V, TA= -40 to +85qC, unless otherwise noted. Typical values are at TA= 25qC Parameter Symbol Condition Min Typ Max Units Feedback Voltage Upper Switch On Resistance Upper Switch Leakage Current Limit VFB RDS ON 4.5V < VIN < 42V, TA= 25qC 4.5V < VIN < 42V VBST VSW = 5V VEN = 0V, VSW = 0V, VIN = 42V Duty Cycle = 50% COMP to Current Sense Transconductance

PDF Datasheet Preview

The Future of Analog IC Technology

The MPQ2560 is a high frequency step-down switching regulator with an integrated internal high-side high voltage power MOSFET. It provides 2.5A output with current mode control for fast loop response and easy compensation.

The wide 4.5V to 42V input range accommodates a variety of step-down applications, including those in an automotive input environment. A 12uA shutdown mode quiescent current allows use in battery-powered applications.

High power conversion efficiency over a wide load range is achieved by scaling down the switching frequency at light load condition to reduce the switching and gate driving losses.

The frequency foldback helps prevent inductor current runaway during startup and thermal shutdown provides reliable, fault tolerant operation.

By switching at 4MHz, the MPQ2560 is able to prevent EMI Electromagnetic Interference noise problems, such as those found in AM radio and ADSL applications.

The MPQ2560 is available in small 3mm x 3mm QFN10 and thermally enhanced SOIC8 packages.

MPQ2560

Industrial Grade 2.5A, 4MHz, 42V Step-Down Converter
x Guaranteed Industrial Temp Range Limits x Quiescent Current x Wide 4.5V to 42V Operating Input Range x 220m Internal Power MOSFET x Up to 4MHz Programmable Switching

Frequency x Stable with Ceramic Capacitor x Internal Soft-Start x Internally Set Current Limit without external

Current Sensing Resistor x Up to 93% Efficiency x Output Adjustable from 0.8V to 39V x Available in 3x3 QFN10 and Thermally

Enhanced SOIC8 Packages
x Industrial Power Systems x High Voltage Power Conversion x Automotive Systems x Distributed Power Systems x Battery Powered Systems
“MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc.
11/19/2009

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2009 MPS. All Rights Reserved.

This datasheet has been downloaded from at this page

GRADE, 2.5A, 4MHz, 42V, STEP-DOWN CONVERTER
8,9 VIN

SW 1,2

MPQ2560
7 FREQ

COMP 4

GND 6

VOUT 3.3V

EFFICIENCY %

Efficiency vs.

Load Current

VIN=12V VIN=8V

VIN=24V

VIN=36V

VOUT=3.3V fs=500kHz
50 0 1 2

LOAD CURRENT A

MPQ2560 INDUSTRIAL GRADE, 2.5A, 4MHz, 42V STEP-DOWN CONVERTER

Part Number* MPQ2560DQ MPQ2560DN
ORDERING INFORMATION

Package 3x3 QFN10

SOIC8E

Top Marking S8

MP2560DN

Ambient Temperature to +85qC
*For Tape & Reel, add suffix eg. For RoHS Compliant Packaging, add suffix eg.
** For Tape & Reel, add suffix eg. For RoHS Compliant Packaging, add suffix eg.

PACKAGE REFERENCE

TOP VIEW

TOP VIEW

SW 1 SW 2 EN 3 COMP 4 FB 5

EXPOSED PAD ON BACKSIDE CONNECT TO GND
10 BST 9 VIN 8 VIN 7 FREQ 6 GND

SW 1 EN 2 COMP 3 FB 4
8 BST 7 VIN 6 FREQ 5 GND

EXPOSED PAD CONNECT TO GND

ABSOLUTE MAXIMUM RATINGS 1

Supply Voltage to +45V Switch Voltage VSW
-7V for < 10ns to VIN + 0.3V BST to SW to +6V All Other Pins to +6V Continuous Power TA = +25°C
3x3 QFN10 2.5W SOIC8 2.5W Junction Temperature ...............................150qC Lead Temperature Storage Temperature.............. to +150qC

Recommended Operating Conditions 3

Supply Voltage VIN ...........................4.5V to 42V Output Voltage VOUT.........................0.8V to 39V Operating Junction to +125qC

Thermal Resistance 4
3x3 QFN10 50 qC/W SOIC8 Exposed Pad 50 qC/W

Notes 1 Exceeding these ratings may damage the device. 2 The maximum allowable power dissipation is a function of the
maximum junction temperature TJ MAX , the junction-toambient thermal resistance and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD MAX = TJ Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3 The device is not guaranteed to function outside of its operating conditions. 4 Measured on JESD51-7 4-layer board.
11/19/2009

MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2009 MPS. All Rights Reserved.

MPQ2560 INDUSTRIAL GRADE, 2.5A, 4MHz, 42V STEP-DOWN CONVERTER

ELECTRICAL CHARACTERISTICS

VIN = 12V, VEN = 2.5V, VCOMP = 1.4V, TA= -40 to +85qC, unless otherwise noted. Typical values are at TA= 25qC

Parameter

Symbol Condition

Min Typ Max Units

Feedback Voltage

Upper Switch On Resistance Upper Switch Leakage Current Limit

VFB RDS ON
4.5V < VIN < 42V, TA= 25qC 4.5V < VIN < 42V VBST VSW = 5V VEN = 0V, VSW = 0V, VIN = 42V Duty Cycle = 50%

COMP to Current Sense Transconductance

More datasheets: ICS1893CFT | MDM-9SH046K | 1502 | 1515 | 1518 | 1508 | 1521 | MPQ2560DQ-LF-P | MPQ2560DN-LF | MPQ2560DN-LF-Z

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MPQ2560DQ-LF-Z Datasheet file may be downloaded here without warranties.

Datasheet ID: MPQ2560DQ-LF-Z 650047