MP5000DQ-LF-P

MP5000DQ-LF-P Datasheet

MP5000

Part	Datasheet
MP5000DQ-LF-P	MP5000DQ-LF-P (pdf)

Related Parts	Information
MP5000DQ-LF-Z	MP5000DQ-LF-Z

PDF Datasheet Preview
The Future of Analog IC Technology MP5000 12V, 5A Programmable Current Limit Switch The MP5000 is a protection device designed to protect circuitry on the output source from transients on input VCC . It also protects VCC from undesired shorts and transients coming from the source. At start up, inrush current is limited by limiting the slew rate at the source. The slew rate is controlled by a small capacitor at the dv/dt pin. The dv/dt pin has an internal circuit that allows the customer to float this pin no connect and still receive 1.1ms ramp time at the source. The max load at the output source is current limited. This is accomplished by utilizing a sense FET topology. The magnitude of the current limit is controlled by an external resistor from the ILimit pin to the Source pin. An internal charge pump drives the gate of the power device, allowing a very low on-resistance DMOS power FET of just The source is protected from the VCC input being too low or too high. Under Voltage Lockout UVLO assures that VCC is above the minimum operating threshold, before the power device is turned on. If VCC goes above the high output threshold, the source voltage will be limited. • Integrated Power FET • Enable/Fault Pin • Adjustable Slew Rate for Output Voltage • Adjustable Current Limit 1-5A • Thermal Protection • Over Voltage Limit • Hot Swap • PC Cards • Laptops For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc. EN Cdv/dt RLIMIT 5 N/C 11 VCC Source 6 4 I-Limit Source 7 MP5000 3 Enable/Fault Source 8 2 dv/dt Source 9 1 GND Source 10 U1 VOUT 9/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2014 MPS. All Rights Reserved. MP5000 12V, 1A-5A PROGRAMMABLE CURRENT LIMIT SWITCH Part Number* MP5000DQ ORDERING INFORMATION Package QFN10 3 x3mm Top Marking V6 Free Air Temperature TA -40°C to +85°C * For Tape & Reel, add suffix e.g. For RoHS Compliant Packaging, add suffix e.g. PACKAGE REFERENCE TOP VIEW GND 1 DV/DT 2 ENABLE/FAULT 3 I-LIMIT 4 N/C 5 EXPOSED PAD VCC 10 SOURCE 9 SOURCE 8 SOURCE 7 SOURCE 6 SOURCE ABSOLUTE MAXIMUM RATINGS 1 VCC, SOURCE, I-LIMIT -0.3V to 22V dv/dt, ENABLE/FAULT..................... -0.3V to 6V Storage Temperature............... -65°C to +155°C Continuous Power Dissipation TA = +25°C 2 2.5W Operating Junction Temperature -40°C to 150°C Input Voltage Operating Range........ 10V to 18V Input Voltage Transient 100mS VIN=25V Thermal Resistance 3 12 ...°C/W Notes 1 Exceeding these ratings may damage the device. 2 The maximum allowable power dissipation is a function of the maximum junction temperature TJ MAX , the junction-toambient thermal resistance and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD MAX = TJ MAX TA / Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3 Measured on JESD51-7 4-layer board. 9/2/2014 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. 2014 MPS. All Rights Reserved. MP5000 12V, 1A-5A PROGRAMMABLE CURRENT LIMIT SWITCH ELECTRICAL CHARACTERISTICS VCC = 12V, Capacitive Load = 100uF, TA=25°C, unless otherwise noted. Parameters Symbol Condition Min Typ Max Units Power FET Delay Time ON Resistance 4 Off State Output Voltage Continuous Current Thermal Latch Shutdown Temperature Under/Over Voltage Protection Output Clamping Voltage Under Voltage Lockout Under Voltage Lockout UVLO Hysteresis Current Limit Hold Current 4 Trip Current dv/dt Circuit Rise Time Enable/Fault Low Level Input Voltage Intermediate Level Input Voltage High Level Input Voltage High State Maximum Voltage Low Level Input Current Sink Maximum Fanout for Fault Signal Maximum Voltage on Enable/Fault Pin Total Device tDLY RDSon VOFF VCLAMP VUVLO VHYST ILIM-SS ILIM-OL

PDF Datasheet Preview

The Future of Analog IC Technology

MP5000
12V, 5A Programmable Current Limit Switch

The MP5000 is a protection device designed to protect circuitry on the output source from transients on input VCC . It also protects VCC from undesired shorts and transients coming from the source.

At start up, inrush current is limited by limiting the slew rate at the source. The slew rate is controlled by a small capacitor at the dv/dt pin. The dv/dt pin has an internal circuit that allows the customer to float this pin no connect and still receive 1.1ms ramp time at the source.

The max load at the output source is current limited. This is accomplished by utilizing a sense FET topology. The magnitude of the current limit is controlled by an external resistor from the ILimit pin to the Source pin.

An internal charge pump drives the gate of the power device, allowing a very low on-resistance DMOS power FET of just

The source is protected from the VCC input being too low or too high. Under Voltage Lockout UVLO assures that VCC is above the minimum operating threshold, before the power device is turned on. If VCC goes above the high output threshold, the source voltage will be limited.
• Integrated Power FET
• Enable/Fault Pin
• Adjustable Slew Rate for Output Voltage
• Adjustable Current Limit 1-5A
• Thermal Protection
• Over Voltage Limit
• Hot Swap
• PC Cards
• Laptops

For MPS green status, please visit MPS website under Quality Assurance. “MPS” and “The Future of Analog IC Technology” are Registered Trademarks of Monolithic Power Systems, Inc.

EN Cdv/dt

RLIMIT
5 N/C
11 VCC Source 6
4 I-Limit

Source 7

MP5000
3 Enable/Fault Source 8
2 dv/dt

Source 9
1 GND

Source 10 U1

VOUT
9/2/2014

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
2014 MPS. All Rights Reserved.

MP5000 12V, 1A-5A PROGRAMMABLE CURRENT LIMIT SWITCH

Part Number* MP5000DQ
ORDERING INFORMATION

Package QFN10 3 x3mm

Top Marking V6

Free Air Temperature TA -40°C to +85°C
* For Tape & Reel, add suffix e.g. For RoHS Compliant Packaging, add suffix e.g.

PACKAGE REFERENCE

TOP VIEW

GND 1 DV/DT 2 ENABLE/FAULT 3 I-LIMIT 4

N/C 5

EXPOSED PAD VCC
10 SOURCE 9 SOURCE 8 SOURCE 7 SOURCE 6 SOURCE

ABSOLUTE MAXIMUM RATINGS 1

VCC, SOURCE, I-LIMIT -0.3V to 22V dv/dt, ENABLE/FAULT..................... -0.3V to 6V

Storage Temperature............... -65°C to +155°C Continuous Power Dissipation TA = +25°C 2
2.5W

Operating Junction Temperature -40°C to 150°C Input Voltage Operating Range........ 10V to 18V Input Voltage Transient 100mS VIN=25V

Thermal Resistance 3 12 ...°C/W

Notes 1 Exceeding these ratings may damage the device. 2 The maximum allowable power dissipation is a function of the
maximum junction temperature TJ MAX , the junction-toambient thermal resistance and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD MAX = TJ MAX TA / Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3 Measured on JESD51-7 4-layer board.
9/2/2014

MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
2014 MPS. All Rights Reserved.

MP5000 12V, 1A-5A PROGRAMMABLE CURRENT LIMIT SWITCH

ELECTRICAL CHARACTERISTICS

VCC = 12V, Capacitive Load = 100uF, TA=25°C, unless otherwise noted.

Parameters

Symbol Condition

Min Typ Max

Units

Power FET

Delay Time

ON Resistance 4

Off State Output Voltage

Continuous Current Thermal Latch Shutdown Temperature Under/Over Voltage Protection Output Clamping Voltage

Under Voltage Lockout Under Voltage Lockout UVLO Hysteresis Current Limit Hold Current 4 Trip Current dv/dt Circuit Rise Time Enable/Fault Low Level Input Voltage Intermediate Level Input Voltage High Level Input Voltage High State Maximum Voltage Low Level Input Current Sink

Maximum Fanout for Fault Signal

Maximum Voltage on Enable/Fault Pin Total Device
tDLY

RDSon VOFF

VCLAMP VUVLO VHYST

ILIM-SS ILIM-OL

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MP5000DQ-LF-P Datasheet file may be downloaded here without warranties.

Datasheet ID: MP5000DQ-LF-P 650034