2002141110
2002141110 Datasheet
Order No. 200214-1110
| Part | Datasheet |
|---|---|
2002141110 |
2002141110 (pdf) |
| PDF Datasheet Preview |
|---|
| zQSFP+ 1-by-1 Cage Insertion Tool 1-by-1 Cage Insertion Tool Application Tooling Specification Sheet Order No. 200214-1110 • Lightweight tool used in the insertion of a zQSFP+ cage in a PCB • Inserts connector to a PCB without damage to the board SCOPE Products Small Form-Factor Pluggable zQSFP+ 1-by-1 Cages with Press-Fit PC Tails Connector Series No. 100014 100014-1231 100014-1240 100014-1340 100014-1346 100014-1443 100014-1540 100014-1546 100014-1643 100014-1744 100014-1232 100014-1242 100014-1341 100014-1347 100014-1444 100014-1541 100014-1547 100014-1644 100014-6547 Connector Order No. 100014-1233 100014-1234 100014-1901 100014-1250 100014-1342 100014-1343 100014-1348 100014-1440 100014-1445 100014-1446 100014-1542 100014-1543 100014-1548 100014-1640 100014-1645 100014-1646 100014-1235 100014-1252 100014-1344 100014-1441 100014-1447 100014-1544 100014-1641 100014-1647 100014-1236 100014-1253 100014-1345 100014-1442 100014-1448 100014-1545 100014-1642 100014-1648 Notes See the following page for tooling operation instructions. This tool requires a “Keep Out Zone” to be free of components. The tool overhangs the rear of the cage to allow for light pipe options. The right and left sides should be 6.4mm . See Figure CAGE ASSEMBLY Figure 1 KEEP OUT ZONE 6.4mm Maximum BOTH SIDES Doc. No ATS-2002141110 Release Date 04-04-17 UNCONTROLLED COPY zQSFP+ 1-by-1 Cage Insertion Tool Operation By hand, place a cage assembly on the PCB. Make sure all compliant tails are engaged in PCB holes. Place the tool on the cage assembly, oriented as shown in Figure Place the tool, cage, and PCB in a press of suitable size and force, and seat the cage as shown. The PCB support not furnished by Molex must have clearance for the connector pins if they pass through the PCB. Note This insertion tool does not contact the PCB when the connector is fully seated. CAGE REAR CAGE ASSEMBLY NOTE TOOL ORIENTATION CAGE FRONT Figure 2 INSERTION TOOL OVER CAGE ASSEMBLY BOTTOM OF CAGE TO SEAT FLUSH ON PCB Application Tooling Support Phone +1-402-458-TOOL 8665 E-Mail Website: Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries all other trademarks listed herein belong to their respective owners. Doc. No ATS-2002141110 Release Date 04-04-17 UNCONTROLLED COPY |
| More datasheets: IDT6116SA25TPI | IDT6116SA25SO8 | IDT6116SA25SOI | IDT6116SA25SOI8 | IDT6116SA25TP | IDT6116SA25SO | IDT6116SA20SOI8 | IDT6116SA45TPG | DDME-36W4P-K127 | CA3100R12S-A10S3 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 2002141110 Datasheet file may be downloaded here without warranties.