ZPRGF-20
ZPRGF-20 Datasheet
ZPRGF-20
| Part | Datasheet |
|---|---|
ZPRGF-20 |
ZPRGF-20 (pdf) |
| PDF Datasheet Preview |
|---|
| RapidConnect Programming Fixture ZPRGF-20 The RapidConnect Programming Fixture provides developers with a selection of convenient interfaces for programming and debugging a RapidConnect ZigBee module. Power J13 is used to select between USB or user-provided DC power sources. To use the USB connection as a power source, the shorting jumper on J13 should be on pins 1-2 this is the default position . To use an external DC power source, the shorting jumper must be moved to pins The on-board LDO will convert either USB-provided 5V or user-provided external power to 3.3V. USB Connection 5V up to 325mA Alternate Power Connectors J15 or J7 - see I/O section Recommended DC Power Source 4-5VDC 325 mA Note If supplying power on J15, do not supply power on J7 Absolute Max Input Voltage 16VDC Note Higher voltage levels will result in damage to the unit . LEDs Four LED indicators are provided TX Flashes when the module transmits serial data RX Flashes when the module receives serial data MAIN PWR Lights when there is 3.3V power present on the board MODULE PWR Lights when there is 3.3V power present on the ZigBee module Connectivity J10 jumper installed on pins 1-2 and pins 3-4 the default positions for those jumpers Normal USB operation - connects module TX/RX pins to USB interface. Note COM port will only be present when the module is powered 25 Prince Arthur Ave. Toronto, Ontario, Canada M5R1B2 Compatibility The following table shows the module versions that each programming fixture can be used to program. Fixture SKU ZPRGF-20 ZPRGF-10 Compatible Module SKU Z357PA20, Z357PA21 Z357PA10 Refer to the Ember EM357 data sheet for complete GPIO usage details and specs. J12 Ember Debug and Programming InSight Port Pin 1 = +3.3v Pin 6 = JCLK/SWCLK Pin 2 = JTDO/SWO Pin 7 = JTMS/SWDIO Pin 3 = nJRST Pin 8 = nReset Pin 4 = JTDI Pin 9 = PTE Pin 5 = GND Pin 10 = PTD J14 mini-B USB Connector J2 Bootloader Mode Installed = Bootloader mode enabled J7 Alternate Power Connection Pin 1 = Vin Pin 2 = GND Note When supplying power on J7, install a jumper on J8 pins 1-2 and J13 pin 2-3, and do not connect a DC plug to J15. See Power section J1 EM357 GPIO J1 pin 1 = +3.3v J1 pin 2 = PB3 J1 pin 3 = PB4 J1 pin 4 = NRESET J1 pin 5 = PA4 J1 pin 6 = PA5 J1 pin 7 = PB2 J1 pin 8 = PA6 J1 pin 9 = PB1 J1 pin 10 = GND All other connections are reserved. Ordering Information The RapidConnect Programming Fixture is included in RapidSE or RapidHA Development Kits, but the fixture can also be purchased separately from MMB Networks or its distributors, using the SKU ZPRGF-20. |
| More datasheets: HSDL-4400#1S1 | HSDL-5420 | HSDL-5420#011 | HSDL-5400#011 | HSDL-5420#031 | CAF94164(IMO-05A) | CAF94148(IMI-02B) | CAF94658(IMI-02D) | CAF95971(IMI-05B) | CAF94659 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ZPRGF-20 Datasheet file may be downloaded here without warranties.