MIKROE-2583

MIKROE-2583 Datasheet

PID MIKROE-2583

Part	Datasheet
MIKROE-2583	MIKROE-2583 (pdf)

PDF Datasheet Preview
SPI Isolator click PID MIKROE-2583 SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface SPI . The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI interface. ADuM4154 features The ADuM4154 has four high-speed channels. The first three channels, CLK, MI/SO, and MO/SI the slash indicates the connection of the particular input and output channel across the isolator are optimized for either low propagation delay in the B grade, or high noise immunity in the A grade. Note For more information about the A and B grade specifications see the datasheet. Take a look at how the click can be connected in the picture below: Note For this example we used the ccRF 3 click and the EasyPIC v7 development board SPI communication SPI Serial Peripheral Interface communication is one of the most popular protocols for sending data between microcontrollers and different peripherals. It is a synchronous protocol the clock signal is provided by the master. For more information take a look at our Learn article about SPI communication. Key features • ADuM4154 module o Supports up to 17 MHz SPI clock speed o 4 high speed, low propagation delay, SPI signal isolation channels • SPI interface • 3.3V or 5V power supply Specification Product Type SPI isolator Applications Sensor isolation, industrial programmable logic controllers PLCs ADuM4154 digital isolator optimized for SPI Key Features The module supports up to 17 MHz SPI clock speed, 4 high speed, low propagation delay, SPI signal isolation channels Key Benefits The ADuM4154 supports up to 4 slave devices Interface SPI Power Supply 3.3V or 5V Compatibility mikroBUS Pinout diagram This table shows how the pinout on SPI Isolator click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns . Notes Pin Notes mikroBUStm Not connected PWM 16 Not connected Not connected NC 2 RST Not connected Slave Select from the Master MSS 3 CS Not connected SPI Clock from the Master Controller MCLK 4 SCK Not connected SPI Data from the Slave to the Master MI/SO Line 5 MISO

PDF Datasheet Preview

SPI Isolator click

PID MIKROE-2583

SPI Isolator click carries the ADuM4154 5kV digital isolator optimized for a serial peripheral interface SPI . The click is designed to run on either 3.3V or 5V power supply. It communicates with the target microcontroller over SPI interface.

ADuM4154 features

The ADuM4154 has four high-speed channels. The first three channels, CLK, MI/SO, and MO/SI the slash indicates the connection of the particular input and output channel across the isolator are optimized for either low propagation delay in the B grade, or high noise immunity in the A grade.

Note For more information about the A and B grade specifications see the datasheet.

Take a look at how the click can be connected in the picture below:

Note For this example we used the ccRF 3 click and the EasyPIC v7 development board

SPI communication

SPI Serial Peripheral Interface communication is one of the most popular protocols for sending data between microcontrollers and different peripherals. It is a synchronous protocol the clock signal is provided by the master. For more information take a look at our Learn article about SPI communication.

Key features
• ADuM4154 module o Supports up to 17 MHz SPI clock speed o 4 high speed, low propagation delay, SPI signal isolation channels
• SPI interface
• 3.3V or 5V power supply

Specification

Product Type SPI isolator

Applications Sensor isolation, industrial programmable logic controllers PLCs

ADuM4154 digital isolator optimized for SPI

Key Features

The module supports up to 17 MHz SPI clock speed, 4 high speed, low propagation delay, SPI signal isolation channels

Key Benefits The ADuM4154 supports up to 4 slave devices

Interface SPI

Power Supply
3.3V or 5V

Compatibility mikroBUS

Pinout diagram

This table shows how the pinout on SPI Isolator click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns .

Notes

Pin Notes
mikroBUStm

Not connected

PWM 16

Not connected

Not connected

NC 2 RST

Not connected

Slave Select from the Master MSS 3 CS

Not connected

SPI Clock from the Master Controller MCLK 4 SCK

Not connected

SPI Data from the Slave to the Master MI/SO Line
5 MISO

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2583 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2583 649384