PID MIKROE-2507 Weight 30 g Condition New product
Part | Datasheet |
---|---|
![]() |
MIKROE-2507 (pdf) |
PDF Datasheet Preview |
---|
ECG 2 click PID MIKROE-2507 Weight 30 g Condition New product Track the patterns of your beating heart with ECG 2 click. ECG 2 click contains ADS1194 sigma converters from Texas Instruments, a programmable gain amplifier PGA , an internal reference, and an onboard oscillator. Table of contents Setup guide How to use the ECG 2 click MikroPlot application Power supply OverVoltage and OverCurrent protection Application Key features Track the patterns of your beating heart with ECG 2 click. ECG 2 click contains ADS1194 16-bit delta-sigma analog-to-digital converters from Texas Instruments, a built-in programmable gain amplifier PGA , an internal reference, and an onboard oscillator. The click communicates with the target MCU over SPI and the following mikroBUS pins PWM, AN and INT. ECG 2 click runs on 3.3V and 5V power supply. Note We offer cables for three electrodes measuring using 3.5mm jack onboard Setup guide How to use the ECG 2 click You will need the following things to start recording your ECG: • 1.ECG 2 click • 2.Cable • 3.Disposable adhesive electrode pads sold in packs of 30 Of course, you will also need a target board with an MCU preferably powered from an external battery . There are two available measuring options: For 3 wire measurement, a 3.5mm jack is used. You can connect the click to a person using three electrodes placed on the left arm, right arm and the left side of the abdomen below the heart or alternatively on the left leg. We offer cables and electrodes that are marked left leg LL red, left arm LA black, right arm RA white . For 4 wire measurement, screw terminals are used. ECG 2 click can also be connected by 4 electrodes that are placed on both arms and legs. MikroPlot application MikroPlot is a free data visualization tool Windows that can be used to generate an ECG. The graph is generated from data sent from the MCU ADC values from ECG click input + time stamp . A UART-USB connection is required. See the learn.mikroe.com article for more information. Power supply ECG 2 click uses both 3.3V and 5V power supply 3.3V is used as digital power supply and 5V is used for analog power supply via linear regulator which gives stabilized 3V at output . OverVoltage and OverCurrent protection OverVoltage and OverCurrent protection is realized over 22k resistors and diodes. Application Measures the electrical activity of a beating heart through electrodes taped to the skin. DISCLAIMER ECG 2 click is a prototyping tool, not a medical-grade device. Do not use it to diagnose patients. Key features • ADS1194 IC o oscillator and reference o programmable gain amplifier • Onboard 3.5mm jack • MikroPlot application • Interface SPI • 3.3V and 5V power supply SPECIFICATION Product Type Biomedical Measures the electrical activity of a beating heart through electrodes taped to the skin Key Features ADS1194 IC, Onboard 3.5mm jack, Mikro Plot application, SPI interface, 3.3V and 5V power supply Ready-to-use example and free software tool to generate ECG plot, record ECG Key Benefits while you watch TV, read email, talk over the phone study patterns to see what excites you HRV - heart rate variability is a good indicator of state of mind . Interface SPI Power Supply 3.3V and 5V Click board size L x mm Pinout diagram |
More datasheets: JANTX1N825-1 | JANTXV1N821-1 | JANTXV1N823-1 | JANTX1N829-1 | MDD310-22N1 | MDD310-12N1 | MDD310-20N1 | MDD310-14N1 | MDD310-18N1 | MDD310-16N1 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2507 Datasheet file may be downloaded here without warranties.