MIKROE-2046

MIKROE-2046 Datasheet

PID MIKROE-2046

Part	Datasheet
MIKROE-2046	MIKROE-2046 (pdf)

PDF Datasheet Preview
WiFi 7 click PID MIKROE-2046 WiFi 7 click carries the IEEE b/g/n module, specifically optimized for power IoT applications. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI interface, with additional functionality provided by the following pins on the mikroBUS line PWM, INT, RST. features The ATWINC1510-MR210PB is a low-power consumption b/g/n module which is specifically optimized for low-power IoT applications. The module has a Cortus APS3 32-bit processor. This processor performs many of the MAC functions, including but not limited to association, authentication, power management, security key management, and MSDU aggregation/de-aggregation. In addition, the processor provides flexibility for various modes of operation, such as STA and AP modes. Module current consumption The table below describes the current consumption of the ATWINC1510-MR210PB module: Additional pins Additional pins on the WiFi 7 click, besides the ones on the mikroBUS line: Key features • o b/g/n 20MHz solution o Integrated PCB antenna o Supports IEEE WEP, WPA, WPA2 Security • SPI interface • 3.3V power supply Specification Type Wi-Fi Applications Optimized for low power IoT applications On-board modules ATWINC1510-MR210PB Key Features b/g/n 20MHz solution, integrated PCB antenna, supports IEEE WEP, WPA, WPA2 Security Interface Power Supply 3.3V Compatibility mikroBUS Click board size M x mm Pinout diagram This table shows how the pinout on WiFi 7 click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns . Notes mikroBUStm Notes Not connected NC 1 AN PWM 16 EN Module Enable Hard Reset RST 2 RST INT 15 INT Device Interrupt output Chip select CS 3 CS TX 14 NC Not connected SPI Clock SCK 4 SCK RX 13 NC Not connected SPI Master Input Slave Output MISO 5 MISO SCL 12 NC Not connected SPI Master Output Slave Input MOSI 6 MOSI SDA 11 NC Not connected Power supply +3.3V 7 3.3V 5V 10 NC Not connected Ground GND 8 GND 9 GND Ground Programming Code examples for WiFi 7 click, written for MikroElektronika hardware and compilers are available on Libstock. Code snippet The following code snippet shows the default main function for all examples. 01 void main void systemInit ; printf "Project built for Click Boardrn" ;

PDF Datasheet Preview

WiFi 7 click

PID MIKROE-2046

WiFi 7 click carries the IEEE b/g/n module, specifically optimized for power IoT applications. The click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI interface, with additional functionality provided by the following pins on the mikroBUS line PWM, INT, RST.
features The ATWINC1510-MR210PB is a low-power consumption b/g/n module which is specifically optimized for low-power IoT applications. The module has a Cortus APS3 32-bit processor. This processor performs many of the MAC functions, including but not limited to association, authentication, power management, security key management, and MSDU aggregation/de-aggregation. In addition, the processor provides flexibility for various modes of operation, such as STA and AP modes.

Module current consumption The table below describes the current consumption of the ATWINC1510-MR210PB module:

Additional pins Additional pins on the WiFi 7 click, besides the ones on the mikroBUS line:

Key features
• o b/g/n 20MHz solution o Integrated PCB antenna o Supports IEEE WEP, WPA, WPA2 Security
• SPI interface
• 3.3V power supply

Specification

Type

Wi-Fi

Applications Optimized for low power IoT applications

On-board modules

ATWINC1510-MR210PB

Key Features
b/g/n 20MHz solution, integrated PCB antenna, supports IEEE WEP, WPA, WPA2 Security

Interface

Power Supply 3.3V

Compatibility mikroBUS

Click board size M x mm

Pinout diagram

This table shows how the pinout on WiFi 7 click corresponds to the pinout on the mikroBUS socket the latter shown in the two middle columns .

Notes
mikroBUStm

Notes

Not connected NC 1 AN PWM 16 EN Module Enable

Hard Reset RST 2 RST INT 15 INT Device Interrupt output

Chip select CS 3 CS TX 14 NC Not connected

SPI Clock SCK 4 SCK RX 13 NC Not connected

SPI Master Input Slave Output MISO 5 MISO SCL 12 NC Not connected

SPI Master Output Slave Input MOSI 6 MOSI SDA 11 NC Not connected

Power supply +3.3V 7 3.3V 5V 10 NC Not connected

Ground GND 8 GND 9 GND Ground

Programming

Code examples for WiFi 7 click, written for MikroElektronika hardware and compilers are available on Libstock.

Code snippet

The following code snippet shows the default main function for all examples.
01 void main void
systemInit ;
printf "Project built for Click Boardrn" ;

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIKROE-2046 Datasheet file may be downloaded here without warranties.

Datasheet ID: MIKROE-2046 649128