PD67101
PD67101 Datasheet
PD67101 POH PSE module
| Part | Datasheet |
|---|---|
PD67101 |
PD67101 (pdf) |
| PDF Datasheet Preview |
|---|
| W. Microsemi .CO M PD67101 POH PSE module Datasheet Microsemi’s Power over Ethernet POE PSE module design to meet IEEE802.3 AF, AT and POH standards. The PD67101 module designed to be used in POH application. This module contains the POH functionality only and will be plugged into motherboard that contains the RJ45, line transformer and PHY. KEY FEATURES • IEEE 802.3AT, IEEE802.3AF and POH standard compliant • Supports POH detection signature and class interface • Up to 95W power support • Power feeding through 4 pairs • Based on Microsemi’s PD69108 and PD69100 chip set • Integrated solution minimum external components • Thermal monitoring and protection capabilities • EN55024 • UL/cUL/CB • RoHS compliant Figure 1 PD67101 Module • HDBase-T up to 95 Watts • IEEE802.3af and 802.3at • Indoor and outdoor PoE PD67101 IMPORTANT For the most current data, consult Microsemi’s website: Copyright 2013 Microsemi Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308 Part Number PD67101 PD67101 POH PSE module Datasheet Ordering Information 1 Port 95W POH PSE module APPLICABLE DOCUMENTS • IEEE 802.3at-2009 standard. • POH standard W. Microsemi .CO M PD67101 Copyright 2013 Microsemi Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308 PD67101 POH PSE module Datasheet MECHANICAL DRWAING W. Microsemi .CO M PD67101 Copyright 2013 Microsemi Analog Mixed Signal Group 1 Enterprise, Aliso Viejo, CA 92656, USA Within the USA 800 713-4113, Outside the USA 949 221-7100 Fax 949 756-0308 W. Microsemi .CO M PD67101 POH PSE module Datasheet # PIN J1 1 2 3 4 5 6 8 9 10 1 2 3 4 5 6 7 8 NAME Input Connector VDC+ NC LED_OUT1 LED_OUT2 DRV_VAUX5 VAUX5 NC VDC- PIN DESCRIPTION 10 pins input connector, located at the left side, receive the power from power supply to be injected on the port and power the module VDC+ LED data for Port 1 Driven outputs for 5 VDC external regulation if internal regulation is used, connect to pin If an external NPN is used to regulate the voltage, connect this pin to the "Base". Regulated 5 VDC output voltage source it needs to be connected to a filtering capacitor of uF or higher. If an external NPN is used to regulate the voltage, connect this pin to the "Emitter" the "collector" should be connected to Vmain NC VDC RTN OUTPUT Connector VDC+ VDC+ VDCVDCVDCVDCVDC+ VDC+ 8 pins input connector, located at the right side, inject the power to the output RJ45 to transformer center-tap A to transformer center-tap A to transformer center-tap B to transformer center-tap B to transformer center-tap D to transformer center-tap D to transformer center-tap C to transformer center-tap C PD67101 Copyright 2013 Microsemi Analog Mixed Signal Group |
| More datasheets: MAX16813ATP+T | MAX16813AUP+T | MAX16813AUP/V+T | MAX16813ATP/V+T | MAX16813AUP/V+ | MAX16813ATP+ | MAX16813AUP+ | FTLFLCDP1 | MIKROE-2006 | DAMZ15SZA197 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived PD67101 Datasheet file may be downloaded here without warranties.