MIC5016BN

MIC5016BN Datasheet


MIC5016/5017

Part Datasheet
MIC5016BN MIC5016BN MIC5016BN (pdf)
Related Parts Information
MIC5016BWM MIC5016BWM MIC5016BWM
PDF Datasheet Preview
MIC5016/5017

Micrel

MIC5016/5017

Low-Cost Dual High- or Low-Side MOSFET Driver Final Information

MIC5016 and MIC5017 dual MOSFET drivers are designed for gate control of N-channel, enhancement-mode, power MOSFETs used as high-side or low-side switches. The MIC5016/7 can sustain an on-state output indefinitely.

The MIC5016/7 operates from a 2.75V to 30V supply. In highside configurations, the driver can control MOSFETs that switch loads of up to 30V. In low-side configurations, with separate supplies, the maximum switched voltage is limited only by the MOSFET.

The MIC5016/7 has two TTL compatible control inputs. The MIC5016 is noninverting while the MIC5017 is inverting.

The MIC5016/7 features internal charge pumps that can sustain gate voltages greater than the available supply voltage. The driver is capable of turning on logic-level MOSFETs from a 2.75V supply or standard MOSFETs from a 5V supply. Gate-to-source output voltages are internally limited to approximately 15V.

The MIC5016 is an improved pin-for-pin compatible replacement in many MIC5012 applications.

The MIC5016/7 is available in plastic 14-pin DIP and 16-pin SOIC pacakges.
+3V to +4V
10µF

ON OFF

ON OFF

MIC5016BN V+ A Gate A V+ B Source A In A Gate B In B Source B Gnd

IRLZ24

Back Light

IRLZ24
• Automotive electrical load control
• Battery-powered computer power management
• Lamp control
• Heater control
• Motor control
• Power bus switching
Ordering Information

Part Number Noninverting MIC5016BWM MIC5016BN Inverting MIC5017BWM MIC5017BN

Temperature Range

Package
to +85°C to +85°C
16-pin Wide SOIC 14-pin Plastic DIP
to +85°C to +85°C
16-pin Wide SOIC 14-pin Plastic DIP

Logic

Figure 1 3-Volt “Sleep-Mode” Switches with Logic-Level MOSFETs

Micrel, Inc.
• 1849 Fortune Drive
• San Jose, CA 95131
• USA
• tel + 1 408 944-0800
• fax + 1 408 944-0970


October 1998

MIC5016/5017

MIC5016/5017

Block Diagram 1 of 2 Drivers per Package

Charge Pump 15V
* Input

Connection Diagram
* Inverting version only
1 NC 2 Source A 3 Gnd 4 Gate A 5 Source B 6 Gate B 7 NC

In A 14 NC 13 V+ A 12 In B 11 V+ B 10 NC 9 NC 8
14-pin DIP

Ground
1 NC 2 Source A 3 Gnd 4 Gate A 5 Source B 6 Gate B 7 NC 8 NC

In A 16 NC 15 V+ A 14 In B 13 V+ B 12 NC 11 NC 10 NC 9
16-pin Wide SOIC

Micrel

Gate Source

Pin Description

Pin Number Pin Number N, J Package WM Package

Pin Name V+A

Input A

Input B

Gate A

Gate B

Source A

Source B

Pin Function

Supply Pin A. Must be decoupled to isolate large transients caused by power MOSFET drain. 10µF is recommended close to pins 12 and/or 10 and ground. V+A and V+B may be connected to separate supplies. Supply Pin B. See V+A. Turns on power MOSFET A when asserted. Requires approximately 1µA to switch. Turns on power MOSFET B. See Input A. Drives and clamps the gate of power MOSFET A Drives and clamps the gate of power MOSFET B Connects the source lead of MOSFET A Connects the source lead of MOSFET B Ground

MIC5016/5017

October 1998
More datasheets: RL110S-221L | RL110S-101L | RL110S-121L | RL110S-120M | RL110S-150M | RL110S-151L | RL110S-180M | RL110S-181L | RL110S-220M | RL110S-100M


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MIC5016BN Datasheet file may be downloaded here without warranties.

Datasheet ID: MIC5016BN 647902