U2795B-MFPG3

U2795B-MFPG3 Datasheet

U2795B

Part	Datasheet
U2795B-MFPG3	U2795B-MFPG3 (pdf)

Related Parts	Information
U2795B-MFP	U2795B-MFP

PDF Datasheet Preview
• Supply-voltage Range V to V • Single-ended Output, no Balun Required • Single-ended Input for RF and LO • Excellent Isolation Characteristics • Power-down Mode • IP3 and Compression Point Programmable • 2.5-GHz Operating Frequency • Reduced System Costs as only Few External Component no Balun are Required • Small Package • Very Low Current Consumption • Easy to Use Electrostatic sensitive device. Observe precautions for handling. 2.5-GHz Doublebalanced Mixer U2795B The U2795B is a 2.5-GHz mixer for WLAN and RF telecommunications equipment, e.g., DECT and PCN. The IC is manufactured using Atmel's advanced bipolar technology. A double-balanced approach was chosen to assure good isolation characteristics and a minimum of spurious products. The input and output are single-ended, and their characteristics are programmable. No output transformer or balun is required. Figure Block Diagram 2 RFi R1 VH VS R2 Voltage regulator 5 IFo 7 LOi Pin Configuration Figure Pinning VS 1 RFI 2 P3 SO 4 Pin Description Function Supply voltage RF input Programming port IP3, CP Output symmetry IF output Ground LO input Power-up 8 PU 7 LOI 6 GND 5 IFO 2 U2795B U2795B Functional Description Supply Voltage The IC is designed for a supply-voltage range of V to V. As the IC is internally stabilized, the performance of the circuit is nearly independent of the supply voltage. Input Impedance The input impedance, ZRFi, is about 700 with an additional capacitive component. This condition provides the best noise figure in combination with a matching network. 3rd Order Intercept Point The voltage divider, RP/R1, determinates both the input and output intercept point, IIP3 and OIP3. If the value of RP is infinite, the maximum value of IIP3 reach about -4 dBm. The IP3/RP characteristics are shown in Figure 3 and Figure Output Impedance and Intercept Point The output impedance is shown in Figure 11 on page Both low output impedance and a high intercept point are defined to a high value of RP. Current Consumption, IS Depending on the chosen input and output conditions of the IC, the current consump- tion, IS, is between 4 mA and 10 mA. The current consumption in dependence of RP is shown in Figure 6 on page Power-up Output Symmetry This feature provides extended battery lifetime. If this function is not used, pin 8 has to be connected to VS pin The symmetry of the load current can be matched and thus optimized for a given load impedance. Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Ordering Information Extended Type Number U2795B-MFP U2795B-MFPG3 Package SO8 Remarks Tube Taped and reeled Package Information Package SO8 Dimensions in mm technical drawings according to DIN specifications 12 U2795B Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 487-2600 Regional Headquarters Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel 41 26-426-5555 Fax 41 26-426-5500 Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369 Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581 Atmel Operations Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314 Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel 33 2-40-18-18-18 Fax 33 2-40-18-19-60 ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel 33 4-42-53-60-00 Fax 33 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel 44 1355-803-000 Fax 44 1355-242-743 RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel 49 71-31-67-0 Fax 49 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel 33 4-76-58-30-00 Fax 33 4-76-58-34-80 Literature Requests Disclaimer Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Atmel Corporation All rights reserved. and combinations thereof are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others. Printed on recycled paper.

PDF Datasheet Preview

• Supply-voltage Range V to V
• Single-ended Output, no Balun Required
• Single-ended Input for RF and LO
• Excellent Isolation Characteristics
• Power-down Mode
• IP3 and Compression Point Programmable
• 2.5-GHz Operating Frequency
• Reduced System Costs as only Few External Component no Balun are Required
• Small Package
• Very Low Current Consumption
• Easy to Use

Electrostatic sensitive device. Observe precautions for handling.
2.5-GHz Doublebalanced Mixer

U2795B

The U2795B is a 2.5-GHz mixer for WLAN and RF telecommunications equipment, e.g., DECT and PCN. The IC is manufactured using Atmel's advanced bipolar technology. A double-balanced approach was chosen to assure good isolation characteristics and a minimum of spurious products. The input and output are single-ended, and their characteristics are programmable. No output transformer or balun is required.

Figure Block Diagram
2 RFi

R1 VH

VS R2

Voltage
regulator
5 IFo
7 LOi

Pin Configuration

Figure Pinning

VS 1 RFI 2

P3 SO 4

Pin Description

Function Supply voltage RF input Programming port IP3, CP Output symmetry IF output Ground LO input Power-up
8 PU 7 LOI 6 GND 5 IFO
2 U2795B

U2795B

Functional Description

Supply Voltage

The IC is designed for a supply-voltage range of V to V. As the IC is internally stabilized, the performance of the circuit is nearly independent of the supply voltage.

Input Impedance

The input impedance, ZRFi, is about 700 with an additional capacitive component. This condition provides the best noise figure in combination with a matching network.
3rd Order Intercept Point The voltage divider, RP/R1, determinates both the input and output intercept point, IIP3
and OIP3. If the value of RP is infinite, the maximum value of IIP3 reach about -4 dBm.

The IP3/RP characteristics are shown in Figure 3 and Figure

Output Impedance and Intercept Point

The output impedance is shown in Figure 11 on page Both low output impedance and a high intercept point are defined to a high value of RP.

Current Consumption, IS

Depending on the chosen input and output conditions of the IC, the current consump-
tion, IS, is between 4 mA and 10 mA. The current consumption in dependence of RP is shown in Figure 6 on page

Power-up Output Symmetry

This feature provides extended battery lifetime. If this function is not used, pin 8 has to be connected to VS pin

The symmetry of the load current can be matched and thus optimized for a given load impedance.

Absolute Maximum Ratings

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Ordering Information

Extended Type Number U2795B-MFP U2795B-MFPG3

Package SO8

Remarks Tube Taped and reeled

Package Information

Package SO8

Dimensions in mm
technical drawings according to DIN specifications
12 U2795B

Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 487-2600

Regional Headquarters

Europe Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel 41 26-426-5555 Fax 41 26-426-5500

Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel 852 2721-9778 Fax 852 2722-1369

Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581

Atmel Operations

Memory 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314

Microcontrollers 2325 Orchard Parkway San Jose, CA 95131, USA Tel 1 408 441-0311 Fax 1 408 436-4314

La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel 33 2-40-18-18-18 Fax 33 2-40-18-19-60

ASIC/ASSP/Smart Cards Zone Industrielle 13106 Rousset Cedex, France Tel 33 4-42-53-60-00 Fax 33 4-42-53-60-01
1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759

Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel 44 1355-803-000 Fax 44 1355-242-743

RF/Automotive Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel 49 71-31-67-0 Fax 49 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel 1 719 576-3300 Fax 1 719 540-1759

Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom

Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel 33 4-76-58-30-00 Fax 33 4-76-58-34-80

Literature Requests

Disclaimer Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems.

Atmel Corporation All rights reserved. and combinations thereof are the registered trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be the trademarks of others.

Printed on recycled paper.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived U2795B-MFPG3 Datasheet file may be downloaded here without warranties.

Datasheet ID: U2795B-MFPG3 519477