and Power-supply Fail Detection<br>• Serial Data Interface, Daisy Chain Capable, up to 2 MHz Clock Frequency<br>• QFN18 Package
Part | Datasheet |
---|---|
![]() |
ATA6831-PISW (pdf) |
Related Parts | Information |
---|---|
![]() |
ATA6831-PIQW |
PDF Datasheet Preview |
---|
• Supply Voltage up to 40V • RDSon Typically at 25°C, Maximum at 150°C • Up to 1.0A Output Current • Three Half-bridge Outputs Formed by Three High-side and Three Low-side Drivers • Capable of Switching Loads such as DC Motors, Bulbs, Resistors, Capacitors, and Inductors • PWM Capability up to 25 kHz for Each High-side Output Controlled by External PWM Signal • No Shoot-through Current • Very Low Quiescent Current IVS < 5 µA in Standby Mode over Total Temperature Range • Outputs Short-circuit Protected • Selective Overtemperature Protection for Each Switch and Overtemperature Prewarning • Undervoltage Protection • Various Diagnostic Functions such as Shorted Output, Open Load, Overtemperature and Power-supply Fail Detection • Serial Data Interface, Daisy Chain Capable, up to 2 MHz Clock Frequency • QFN18 Package Triple Half-bridge Driver with SPI and PWM ATA6831 The ATA6831 provides fully protected driver interfaces designed in SOI technology. They are used to allow a microcontroller to control up to 3 different loads in automotive and industrial applications. Each of the 3 high-side and 3 low-side drivers is capable of driving currents up to 1.0A. Due to the enhanced PWM signal up to 25 kHz it is possible to generate a smooth control of, for example, a DC motor without any noise. The drivers are internally connected to form 3 half-bridges and can be controlled separately from a standard serial data interface, enabling all kinds of loads, such as bulbs, resistors, capacitors and inductors, to be combined. The IC design especially supports the application of H-bridges to drive DC motors. Protection is guaranteed with respect to short-circuit conditions, overtemperature and undervoltage. Various diagnostic functions and a very low quiescent current in standby mode enable a wide range of applications. Automotive qualification protection against conducted interferences, EMC protection and 2-kV ESD protection gives added value and enhanced quality for exacting requirements of automotive applications. Figure Block Diagram CLK 5 PWM 6 O OP P H L H L H L S LH L H L H L S SS S R I C D3 3 2 1 3 2 1 R Input register Ouput register Serial interface P I O n. n. n. n. n. n. H L H L H L T S N V u. u. u. u. u. u. S P 3 2 21 1 Fault detector Fault detector Fault detector Control logic Fault detector Fault detector OUT3S OUT3F 13 OUT2S Fault detector Thermal protection OUT2F OUT1S 15 OUT1F Charge pump VS1 11 UV protection Power on reset 9 VCC 8 GND 14 GND 17 GND 18 GND 2 ATA6831 Ordering Information Extended Type Number ATA6831-PIQW ATA6831-PIPW ATA6831-PISW Package QFN18, 4 mm x 4 mm QFN18, 4 mm x 4 mm QFN18, 4 mm x 4 mm Package Information Remarks Taped and reeled, Pb-free Taped and reeled, Pb-free Tubes, Pb-free Package VQFN_4 x 4_18L Exposed pad x Dimensions in mm Not indicated tolerances Pin 1 identification Top 18 Bottom Z nom. Drawing-No. Issue 1; Z 10:1 technical drawings according to DIN specifications History 4908G-AUTO-07/10 • Section Open-load Detection on page 6 changed • Section 8 “Electrical Characteristics” numbers and on pages 10 to 11 changed. • Section 8 “Electrical Characteristics” numbers 4.12a, 4.13a and on pages 10 to 11 added. 4908F-AUTO-02/10 • Section 5 “Thermal Resistance” on page 8 changed 4908E-AUTO-06/07 • Put datasheet into the newest template • Package drawing changed • Block diagram changed • Pin description table changed • El. Char. table rows and changed • El. Char. table row deleted • Application circuit drawing changed 4908D-AUTO-09/06 • Features on page 1 changed • Figure 1-1 “Block Diagram” on page 2 changed • Section 2 “Pin Configuration” on pages 2 to 3 changed • Section 4 “Absolute Maximum Ratings” on page 8 changed • Section 8 “Electrical Characteristics” on pages 9 to 11 changed • Section 9 “Serial Interface Timing” on page 12 changed • Figure 10-1 “Application Circuit” on page 14 changed • Section 11 “Ordering Information” on page 15 changed • Section 12 “Package Information” on page 15 changed 4908C-AUTO-08/06 • Title on page 1 changed • Features on page 1 changed • Figure 1-1 “Block Diagram” on page 1 changed • Figure 2-1 “Pinning” on page 3 changed • Table 2-1 “Pin Description” on page 3 changed • Table 3-2 “Output Data Protocol” on page 5 changed • Section “PWM Mode” on page 7 added • Section 4 “Absolute Maximum Ratings” on page 8 changed • Section 8 “Electrical Characteristics” on pages 9 to 12 changed • Figure 10-1 “Application Circuit” on page 14 changed • Section “Application Notes” on page 14 changed • Section 11 “Ordering Information” on page 15 changed • Section 12 “Package Information” on page 15 changed 16 ATA6831 Headquarters Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel 1 408 441-0311 Fax 1 408 487-2600 International Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Tel 852 2245-6100 Fax 852 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-en-Yvelines Cedex France Tel 33 1-30-60-70-00 Fax 33 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel 81 3-3523-3551 Fax 81 3-3523-7581 Product Contact Web Site Literature Requests Technical Support Sales Contact Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. 2010 Atmel Corporation. All rights reserved. logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. |
More datasheets: B484312S2557 | A480314S2558 | TCABLE-K | 96HD1TB-ST-SG7KA1 | AP3608EGTR-G1 | AP3608EFNTR-G1 | AP3608EM-G1 | AP3608EMTR-G1 | AD9941BSTZ | AD9941BSTZRL |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ATA6831-PISW Datasheet file may be downloaded here without warranties.