ATA5830-PNQW

ATA5830-PNQW Datasheet

Full Sensitivity Level 15dB reduced Sensitivity • Programmable Channel Frequency with Fractional-N PLL 93Hz Resolution for Low-Band 185Hz Resolution for High-Band • FSK Deviation ±0.375kHz to ±93kHz • FSK Sensitivity Manchester Coded at 433.92MHz at 20Kbit/s, = ±20kHz, BWIF = 165kHz at 10Kbit/s, = ±10kHz, BWIF = 165kHz at 5Kbit/s, = ±5kHz, BWIF = 165kHz at 0.75Kbit/s, = ±0.75kHz, BWIF = 25kHz • ASK Sensitivity Manchester Coded at 433.92MHz at 20Kbit/s, BWIF = 366kHz at 1Kbit/s, BWIF = 366kHz • Programmable RX-IF Bandwidth 25kHz to 366kHz approx. 10% Steps • Blocking BWIF = 165kHz 64dBC at Freq. Offset = 1MHz and 48dBC at 225kHz • High Image Rejection 55dB 315MHz/433.92MHz 47dB 868.3MHz/915MHz without Calibration • Supported Buffered Data Rate 0.5Kbit/s to 20Kbit/s Higher Data Rates up to 80Kbit/s Manchester Coded and 160Kbit/s NRZ with Transparent Data In/Output • Supports Pattern Based Wake-Up and Start of Frame Identification • Digital RSSI with Very High Relative Accuracy of ±1dB due to Digitized IF Processing • Programmable Clock Output Derived from Crystal Frequency • 24KB ROM with Atmel Firmware and Integrated Microcontroller for Control • 6KB In System Self Programmable Flash for an Additional Customer Application Software • 512 byte EEPROM Data Memory for Transceiver Configuration and 768 byte SRAM • SPI Interface for RX/TX Data Access and Transceiver Configuration • Configurable EVENT Signal Indicates the Status of the IC • Automatic Antenna Tuning at TX Center Frequency for Loop Antenna • Automatic Low Power Channel Polling 3 RKE channels, TPMS, RS • ID Scanning up to 18 Different IDs with byte • Supply Voltage Ranges 1.9V to 3.6V and 4.5V to 5.5V • Temperature Range to +105°C • ESD Protection at all Pins ±4kV HBM, ±200V MM, ±750V FCDM • Small 5mm x 5mm QFN32 Package/Pitch 0.5mm • Suitable for Applications Governed by EN 300 220 and FCC Part 15, Title 47

Part	Datasheet
ATA5830-PNQW	ATA5830-PNQW (pdf)

Related Parts	Information
ATA5830N-PNQW	ATA5830N-PNQW

PDF Datasheet Preview
• Supported Frequency Ranges Low-band 310MHz to 318MHz, 418MHz to 477MHz High-band 836MHz to 928MHz 315.00MHz/433.92MHz/868.30MHz and 915.00MHz with one 24.305MHz Crystal • Low Current Consumption 9.3mA for RXMode Low-Band 480µA for 50ms cycle 3 Channel Polling 9.1mA/13.8mA for TXMode Low-Band, Pout = 6dBm/10dBm • Typical OFFMode Current of 5nA Max. 600nA at Vs = 3.6V and T = 85°C • Programmable Output Power to +14.5dBm 0.4dB Step • Input 1dB Compression Point Full Sensitivity Level 15dB reduced Sensitivity • Programmable Channel Frequency with Fractional-N PLL 93Hz Resolution for Low-Band 185Hz Resolution for High-Band • FSK Deviation ±0.375kHz to ±93kHz • FSK Sensitivity Manchester Coded at 433.92MHz at 20Kbit/s, = ±20kHz, BWIF = 165kHz at 10Kbit/s, = ±10kHz, BWIF = 165kHz at 5Kbit/s, = ±5kHz, BWIF = 165kHz at 0.75Kbit/s, = ±0.75kHz, BWIF = 25kHz • ASK Sensitivity Manchester Coded at 433.92MHz at 20Kbit/s, BWIF = 366kHz at 1Kbit/s, BWIF = 366kHz • Programmable RX-IF Bandwidth 25kHz to 366kHz approx. 10% Steps • Blocking BWIF = 165kHz 64dBC at Freq. Offset = 1MHz and 48dBC at 225kHz • High Image Rejection 55dB 315MHz/433.92MHz 47dB 868.3MHz/915MHz without Calibration • Supported Buffered Data Rate 0.5Kbit/s to 20Kbit/s Higher Data Rates up to 80Kbit/s Manchester Coded and 160Kbit/s NRZ with Transparent Data In/Output • Supports Pattern Based Wake-Up and Start of Frame Identification • Digital RSSI with Very High Relative Accuracy of ±1dB due to Digitized IF Processing • Programmable Clock Output Derived from Crystal Frequency • 24KB ROM with Atmel Firmware and Integrated Microcontroller for Control • 6KB In System Self Programmable Flash for an Additional Customer Application Software • 512 byte EEPROM Data Memory for Transceiver Configuration and 768 byte SRAM • SPI Interface for RX/TX Data Access and Transceiver Configuration • Configurable EVENT Signal Indicates the Status of the IC • Automatic Antenna Tuning at TX Center Frequency for Loop Antenna • Automatic Low Power Channel Polling 3 RKE channels, TPMS, RS • ID Scanning up to 18 Different IDs with byte • Supply Voltage Ranges 1.9V to 3.6V and 4.5V to 5.5V • Temperature Range to +105°C • ESD Protection at all Pins ±4kV HBM, ±200V MM, ±750V FCDM • Small 5mm x 5mm QFN32 Package/Pitch 0.5mm • Suitable for Applications Governed by EN 300 220 and FCC Part 15, Title 47 UHF ASK/FSK Transceiver Atmel ATA5830 ATA5830N Summary NOTE This is a summary document. The complete document is available under NDA. For more information, please contact your local Atmel sales office. General Product Description Overview The ATA5830 is a highly integrated, low power UHF ASK/FSK RF-transceiver. The Atmel ATA5830 is partitioned into several sections an RF frontend, a digital baseband, and a low power 8 bit AVR microcontroller. The product is designed for the ISM frequency bands in the ranges of 310 to 318MHz, 418 to 477MHz and 836 to 928MHz. External part count is kept to a minimum due to the very high level of integration in this device. By combining outstanding RF performance with highly sophisticated baseband signal processing, robust wireless communication can be easily achieved. The receive path uses a low-IF architecture with an integrated double quadrature receiver and digitized IF processing. This results in high image rejection and excellent blocking performance. The transmit path uses a closed loop fractional-N modulator with gaussian shaping and preemphasis functionality for high data rates. In addition, the highly flexible and configurable baseband signal processing allows the transceiver to operate in several scanning, wake-up and automatic self polling scenarios. For example, during polling the IC can seek certain message content IDs and save valid telegram data in the FIFO buffer for later retrieval. The device possess two receive paths that enable parallel search for two telegrams with different modulations, data rates, wake-up conditions, etc. The highly configurable and autonomous scanning capability enables polling of up to five application channels such as 3-channel RKE, TPMS, PEG. The configuration of the transceiver is stored in a 512 byte EEPROM. The SPI allows for external control and reconfiguration of the device. The internal microcontroller and 6 KB Flash can be used to add customer extensions to the Atmel firmware. The debug wire and ISP interface are available for programming purposes. Target Applications The transceiver is designed to be used in the following application areas: • Remote Keyless Entry System RKE • Passive Entry Go System PEG • Tire Pressure Monitoring System TPM,TPMS • Remote Start System RS • Remote Control System, e.g. garage door open • Smart RF applications • Telemetering Systems Three applications with a total of 5 channels are supported by the Atmel firmware for autonomous self polling. 2 Atmel ATA5830/ATA5830N Atmel ATA5830/ATA5830N Main Extended Features of the Atmel ATA5830 RF Performance The ATA5830 provides high sensitivity and programmable transmit power up to 14dBm. The high image rejection and outstanding blocking performance enable a robust application against interferer with a low cost design. In addition, the programmable channel filter bandwidth provides flexibility to adapt to various system requirements. Automatic Self Polling and Multi Channel Capability The autonomous self polling supports the automatic scanning for three different applications such as Remote Keyless Entry RKE , Tire Pressure Monitoring System TPMS and Remote Start RS using one IC. Additionally multi channel systems with up to three frequencies can be scanned. This means five frequencies can be scanned in the autonomous polling scheme three for RKE, one for TPMS and one for RS. The configuration of each application is independent of the others. This is possible because of the flexibility in the digital baseband and two different baseband receiving paths. The IC can immediately scan all applications upon power-up without the need for any initial configuration by an external microcontroller. Wake-up Scenario and ID Scanning The powerful baseband signal processing is designed to offload these time consuming tasks from the host controller. This allows the transceiver to discard unwanted telegrams and limit external microcontroller wake up to valid telegrams only. Up to 7 criteria can be used to determine the telegram validity from carrier check on the lowest level to start of frame ID pattern match at the highest level. Two Parallel Receiving Paths The transceiver’s baseband contains two data paths. The parameters of both paths can be set differently, e.g. the modulation type or data rate. Generally both paths are working simultaneously but only the first path detecting a valid telegram will be used for further data reception and filling of the 32 byte buffer. The 32 byte receive data buffer can be accessed using SPI commands from the external host microcontroller. Channel Statistic In order to accelerate the communication in multi channel applications the Atmel ATA5830 offers a feature defined as channel statistic. If this feature is selected, the IC will find the best channel within the three RKE channels with regard to interference and automatically select the best channel for the first transmission. Antenna Tuning and SPDT For applications using a loop antenna, the Atmel ATA5830 offers an automatic antenna tuning feature which improves the antenna performance by compensating for “hand effects” or matching component value variations. The integrated SPDT acts as RX/TX switch which eliminates the cost of an external RX/TX switch. Customer Application Software All the functionality is implemented in 24KB of ROM firmware and controlled by SPI commands. In addition, 6KB of Flash is available to enable customer specific software functionality. Examples for flash customization are a extension of SPI commands, b usage of a single wire interface instead of SPI, c polling adaptations, d protocol handling, etc. To achieve customer specific functionality, parts of the ROM code can be replaced with Flash code. EEPROM Configuration The configuration of the device e.g. RF-frequency, modulation type, data rate, etc. is stored in 512KB of EEPROM that is integrated within the ATA5830. This improves the efficiency of the SPI control since most of the configuration comes from the EEPROM. In most applications, only the received or transmitted data and short SPI commands are required. The device is delivered with a standard configuration only deviations from that need to be configured. Device configuration uses only a part of the 512KB of EEPROM leaving free space available for additional customer data storage. Pin Diagram and Configuration of Atmel ATA5830 Figure Pin Diagram ATEST_IO1 ATEST_IO2 AGND PB7 PB6 PB5 PB4 PB3 RFIN_LB RFIN_HB 32 31 30 29 28 27 26 25 1 exposed die pad 24 PB2 23 PB1 SPDT_RX 3 22 PB0 SPDT_ANT 4 ANT_TUNE 5 Atmel ATA5830 21 DGND 20 DVCC SPDT_TX 6 19 PC5 RF_OUT 7 18 PC4 VS_PA 8 4 Ordering Information Extended Type Number ATA5830-PNQW ATA5830N-PNQW 5 Package Information Top View D PIN 1 ID 8 Side View Package QFN32 Atmel ATA5830/ATA5830N Remarks 5mm x 5mm PB free 5mm x 5mm PB free technical drawings according to DIN specifications Dimensions in mm Bottom View D2 24 25 Z 10:1 COMMON DIMENSIONS Unit of Measure = mm Symbol MIN NOM MAX NOTE Package Drawing Contact Package VQFN_5x5_32L Exposed pad 3.6x3.6 History 9208DS-RKE-07/11 • Set datasheet from Preliminary to standard 9208CS-RKE-07/11 • Document completely redesigned 9208BS-RKE-01/11 • Section 5 “Ordering Information” on page 29 changed 26 Atmel ATA5830/ATA5830N Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel +1 408 441-0311 Fax +1 408 487-2600 Atmel Asia Limited Unit 01-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel +852 2245-6100 Fax +852 2722-1369 Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel +49 89-31970-0 Fax +49 89-3194621 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel +81 3 3523-3551 Fax +81 3 3523-7581 Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

PDF Datasheet Preview

• Supported Frequency Ranges Low-band 310MHz to 318MHz, 418MHz to 477MHz High-band 836MHz to 928MHz 315.00MHz/433.92MHz/868.30MHz and 915.00MHz with one 24.305MHz Crystal
• Low Current Consumption 9.3mA for RXMode Low-Band 480µA for 50ms cycle 3 Channel Polling 9.1mA/13.8mA for TXMode Low-Band, Pout = 6dBm/10dBm
• Typical OFFMode Current of 5nA Max. 600nA at Vs = 3.6V and T = 85°C
• Programmable Output Power to +14.5dBm 0.4dB Step
• Input 1dB Compression Point

Full Sensitivity Level 15dB reduced Sensitivity
• Programmable Channel Frequency with Fractional-N PLL 93Hz Resolution for Low-Band 185Hz Resolution for High-Band
• FSK Deviation ±0.375kHz to ±93kHz
• FSK Sensitivity Manchester Coded at 433.92MHz at 20Kbit/s, = ±20kHz, BWIF = 165kHz at 10Kbit/s, = ±10kHz, BWIF = 165kHz at 5Kbit/s, = ±5kHz, BWIF = 165kHz at 0.75Kbit/s, = ±0.75kHz, BWIF = 25kHz
• ASK Sensitivity Manchester Coded at 433.92MHz at 20Kbit/s, BWIF = 366kHz at 1Kbit/s, BWIF = 366kHz
• Programmable RX-IF Bandwidth 25kHz to 366kHz approx. 10% Steps
• Blocking BWIF = 165kHz 64dBC at Freq. Offset = 1MHz and 48dBC at 225kHz
• High Image Rejection 55dB 315MHz/433.92MHz 47dB 868.3MHz/915MHz without Calibration
• Supported Buffered Data Rate 0.5Kbit/s to 20Kbit/s Higher Data Rates up to 80Kbit/s Manchester Coded and 160Kbit/s NRZ with Transparent Data In/Output
• Supports Pattern Based Wake-Up and Start of Frame Identification
• Digital RSSI with Very High Relative Accuracy of ±1dB due to Digitized IF Processing
• Programmable Clock Output Derived from Crystal Frequency
• 24KB ROM with Atmel Firmware and Integrated Microcontroller for Control
• 6KB In System Self Programmable Flash for an Additional Customer Application Software
• 512 byte EEPROM Data Memory for Transceiver Configuration and 768 byte SRAM
• SPI Interface for RX/TX Data Access and Transceiver Configuration
• Configurable EVENT Signal Indicates the Status of the IC
• Automatic Antenna Tuning at TX Center Frequency for Loop Antenna
• Automatic Low Power Channel Polling 3 RKE channels, TPMS, RS
• ID Scanning up to 18 Different IDs with byte
• Supply Voltage Ranges 1.9V to 3.6V and 4.5V to 5.5V
• Temperature Range to +105°C
• ESD Protection at all Pins ±4kV HBM, ±200V MM, ±750V FCDM
• Small 5mm x 5mm QFN32 Package/Pitch 0.5mm
• Suitable for Applications Governed by EN 300 220 and FCC Part 15, Title 47

UHF ASK/FSK Transceiver Atmel ATA5830 ATA5830N Summary

NOTE This is a summary document. The complete document is available under NDA. For more information, please contact your local Atmel sales office.

General Product Description

Overview

The ATA5830 is a highly integrated, low power UHF ASK/FSK RF-transceiver. The Atmel ATA5830 is partitioned into several sections an RF frontend, a digital baseband, and a low power 8 bit AVR microcontroller. The product is designed for the ISM frequency bands in the ranges of 310 to 318MHz, 418 to 477MHz and 836 to 928MHz. External part count is kept to a minimum due to the very high level of integration in this device. By combining outstanding RF performance with highly sophisticated baseband signal processing, robust wireless communication can be easily achieved. The receive path uses a low-IF architecture with an integrated double quadrature receiver and digitized IF processing. This results in high image rejection and excellent blocking performance. The transmit path uses a closed loop fractional-N modulator with gaussian shaping and preemphasis functionality for high data rates. In addition, the highly flexible and configurable baseband signal processing allows the transceiver to operate in several scanning, wake-up and automatic self polling scenarios. For example, during polling the IC can seek certain message content IDs and save valid telegram data in the FIFO buffer for later retrieval. The device possess two receive paths that enable parallel search for two telegrams with different modulations, data rates, wake-up conditions, etc. The highly configurable and autonomous scanning capability enables polling of up to five application channels such as 3-channel RKE, TPMS, PEG. The configuration of the transceiver is stored in a 512 byte EEPROM. The SPI allows for external control and reconfiguration of the device. The internal microcontroller and 6 KB Flash can be used to add customer extensions to the Atmel firmware. The debug wire and ISP interface are available for programming purposes.

Target Applications

The transceiver is designed to be used in the following application areas:
• Remote Keyless Entry System RKE
• Passive Entry Go System PEG
• Tire Pressure Monitoring System TPM,TPMS
• Remote Start System RS
• Remote Control System, e.g. garage door open
• Smart RF applications
• Telemetering Systems Three applications with a total of 5 channels are supported by the Atmel firmware for autonomous self polling.
2 Atmel ATA5830/ATA5830N

Atmel ATA5830/ATA5830N

Main Extended Features of the Atmel ATA5830

RF Performance The ATA5830 provides high sensitivity and programmable transmit power up to 14dBm. The high image rejection and outstanding blocking performance enable a robust application against interferer with a low cost design. In addition, the programmable channel filter bandwidth provides flexibility to adapt to various system requirements.

Automatic Self Polling and Multi Channel Capability The autonomous self polling supports the automatic scanning for three different applications such as Remote Keyless Entry RKE , Tire Pressure Monitoring System TPMS and Remote Start RS using one IC. Additionally multi channel systems with up to three frequencies can be scanned. This means five frequencies can be scanned in the autonomous polling scheme three for RKE, one for TPMS and one for RS. The configuration of each application is independent of the others. This is possible because of the flexibility in the digital baseband and two different baseband receiving paths. The IC can immediately scan all applications upon power-up without the need for any initial configuration by an external microcontroller.

Wake-up Scenario and ID Scanning The powerful baseband signal processing is designed to offload these time consuming tasks from the host controller. This allows the transceiver to discard unwanted telegrams and limit external microcontroller wake up to valid telegrams only. Up to 7 criteria can be used to determine the telegram validity from carrier check on the lowest level to start of frame ID pattern match at the highest level.

Two Parallel Receiving Paths The transceiver’s baseband contains two data paths. The parameters of both paths can be set differently, e.g. the modulation type or data rate. Generally both paths are working simultaneously but only the first path detecting a valid telegram will be used for further data reception and filling of the 32 byte buffer. The 32 byte receive data buffer can be accessed using SPI commands from the external host microcontroller.

Channel Statistic In order to accelerate the communication in multi channel applications the Atmel ATA5830 offers a feature defined as channel statistic. If this feature is selected, the IC will find the best channel within the three RKE channels with regard to interference and automatically select the best channel for the first transmission.

Antenna Tuning and SPDT For applications using a loop antenna, the Atmel ATA5830 offers an automatic antenna tuning feature which improves the antenna performance by compensating for “hand effects” or matching component value variations. The integrated SPDT acts as RX/TX switch which eliminates the cost of an external RX/TX switch.

Customer Application Software All the functionality is implemented in 24KB of ROM firmware and controlled by SPI commands. In addition, 6KB of Flash is available to enable customer specific software functionality. Examples for flash customization are a extension of SPI commands, b usage of a single wire interface instead of SPI, c polling adaptations, d protocol handling, etc. To achieve customer specific functionality, parts of the ROM code can be replaced with Flash code.

EEPROM Configuration

The configuration of the device e.g. RF-frequency, modulation type, data rate, etc. is stored in 512KB of EEPROM that is integrated within the ATA5830. This improves the efficiency of the SPI control since most of the configuration comes from the EEPROM. In most applications, only the received or transmitted data and short SPI commands are required. The device is delivered with a standard configuration only deviations from that need to be configured. Device configuration uses only a part of the 512KB of EEPROM leaving free space available for additional customer data storage.

Pin Diagram and Configuration of Atmel ATA5830

Figure Pin Diagram

ATEST_IO1 ATEST_IO2 AGND PB7 PB6 PB5 PB4 PB3

RFIN_LB RFIN_HB
32 31 30 29 28 27 26 25
1 exposed die pad
24 PB2 23 PB1

SPDT_RX 3
22 PB0

SPDT_ANT 4 ANT_TUNE 5

Atmel ATA5830
21 DGND 20 DVCC

SPDT_TX 6
19 PC5

RF_OUT 7
18 PC4

VS_PA 8
4 Ordering Information

Extended Type Number ATA5830-PNQW ATA5830N-PNQW
5 Package Information

Top View D

PIN 1 ID 8

Side View

Package QFN32

Atmel ATA5830/ATA5830N

Remarks 5mm x 5mm PB free 5mm x 5mm PB free
technical drawings according to DIN specifications Dimensions in mm

Bottom View D2
24 25

Z 10:1

COMMON DIMENSIONS Unit of Measure = mm

Symbol MIN NOM MAX NOTE

Package Drawing Contact Package VQFN_5x5_32L Exposed pad 3.6x3.6

History
9208DS-RKE-07/11
• Set datasheet from Preliminary to standard
9208CS-RKE-07/11
• Document completely redesigned
9208BS-RKE-01/11
• Section 5 “Ordering Information” on page 29 changed
26 Atmel ATA5830/ATA5830N

Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel +1 408 441-0311 Fax +1 408 487-2600

Atmel Asia Limited Unit 01-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel +852 2245-6100 Fax +852 2722-1369

Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel +49 89-31970-0 Fax +49 89-3194621

Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel +81 3 3523-3551 Fax +81 3 3523-7581

Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

Disclaimer The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ATA5830-PNQW Datasheet file may be downloaded here without warranties.

Datasheet ID: ATA5830-PNQW 519191