AT93C46C-10SI-2.7
AT93C46C-10SI-2.7 Datasheet
The AT93C46C provides 1024 bits of serial electrically-erasable programmable read only memory EEPROM organized as 64 words of 16 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT93C46C is available in space saving 8lead PDIP and 8-lead JEDEC SOIC packages.
| Part | Datasheet |
|---|---|
AT93C46C-10SI-2.7 |
AT93C46C-10SI-2.7 (pdf) |
| Related Parts | Information |
|---|---|
|
AT93C46C-10PI-2.7 |
AT93C46C-10PI-2.7 |
|
AT93C46C-10SI-2.5 |
AT93C46C-10SI-2.5 |
| PDF Datasheet Preview |
|---|
| • Low-Voltage and Standard-Voltage Operation VCC = 2.7V to 5.5V VCC = 2.5V to 5.5V • 3-Wire Serial Interface • Schmitt Trigger, Filtered Inputs for Noise Suppression • 2 MHz Clock Rate 5V • Self-Timed Write Cycle 10 ms max • High Reliability Endurance 1 Million Write Cycles Data Retention 100 Years • Automotive Grade and Extended Temperature Devices Available • 8-lead PDIP and 8-lead JEDEC SOIC Packages The AT93C46C provides 1024 bits of serial electrically-erasable programmable read only memory EEPROM organized as 64 words of 16 bits each. The device is optimized for use in many industrial and commercial applications where low-power and low-voltage operation are essential. The AT93C46C is available in space saving 8lead PDIP and 8-lead JEDEC SOIC packages. The AT93C46C is enabled through the Chip Select pin CS , and accessed via a 3wire serial interface consisting of Data Input DI , Data Output DO , and Shift Clock SK . Upon receiving a READ instruction at DI, the address is decoded and the data is clocked out serially on the data output pin DO. The WRITE cycle is completely selftimed and no separate ERASE cycle is required before WRITE. The WRITE cycle is only enabled when the part is in the ERASE/WRITE ENABLE state. When CS is brought “high” following the initiation of a WRITE cycle, the DO pin outputs the READY/BUSY status of the part. The AT93C46C is available in 2.7V to 5.5V and 2.5V to 5.5V versions. Pin Configurations Pin Name Function Chip Select Serial Data Clock Serial Data Input Serial Data Output GND VCC Ground Power Supply No Connect Don’t Connect 8-lead PDIP CS 1 SK 2 DI 3 DO 4 8 VCC 7 DC 6 NC 5 GND 8-lead SOIC CS 1 SK 2 DI 3 DO 4 8 VCC 7 DC 6 NC 5 GND 3-Wire Serial EEPROM 1K 64 x 16 AT93C46C Absolute Maximum Ratings* Operating -55°C to +125°C Storage Temperature -65°C to +150°C Voltage on Any Pin with Respect to Ground to +7.0V Maximum Operating Voltage 6.25V DC Output mA Block Diagram *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 AT93C46C AT93C46C Pin Capacitance 1 Applicable over recommended operating range from TA = 25°C, f = MHz, VCC = +5.0V unless otherwise noted . Symbol Test Conditions Units Conditions COUT CIN Note: Output Capacitance DO Input Capacitance CS, SK, DI This parameter is characterized and is not 100% tested. VOUT = 0V VIN = 0V Ordering Information Ordering Code Package Operation Range AT93C46C-10PI-2.7 AT93C46C-10SI-2.7 Industrial -40°C to 85°C AT93C46C-10PI-2.5 AT93C46C-10SI-2.5 Industrial -40°C to 85°C Note For 2.7V and 2.5V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. Package Type 8-lead, Wide, Plastic Dual Inline Package PDIP 8-lead, Wide, Plastic Gull Wing Small Outline JEDEC SOIC Options Low Voltage 2.7V to 5.5V Low Voltage 2.5V to 5.5V Packaging Information 8P3 PDIP Top View End View 4 PLCS Side View COMMON DIMENSIONS Unit of Measure = inches SYMBOL A A2 b b2 b3 c D D1 E E1 e eA L MIN NOM MAX NOTE 2 This drawing is for general information only refer to JEDEC Drawing MS-001, Variation BA for additional information. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed inch. E and eA measured with the leads constrained to be perpendicular to datum. Pointed or rounded lead tips are preferred to ease insertion. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed mm . 01/09/02 2325 Orchard Parkway R San Jose, CA 95131 TITLE 8P3, 8-lead, Wide Body, Plastic Dual In-line Package PDIP 12 AT93C46C 8S1 JEDEC SOIC Top View AT93C46C Side View End View SYMBOL A B C D E H L COMMON DIMENSIONS Unit of Measure = mm MIN NOM MAX NOTE Note This drawing is for general information only. Refer to JEDEC Drawing MS-012 for proper dimensions, tolerances, datums, etc. |
| More datasheets: 2246 | 5581301001 | 5581201001 | 5580301003 | 5580501003 | 5580701003 | 5580601003 | 5580701007 | 89422712 | 1985 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT93C46C-10SI-2.7 Datasheet file may be downloaded here without warranties.