AT88SC-DK1

AT88SC-DK1 Datasheet


AT88SC-DK1 WELCOME AND QUICK START GUIDE

Part Datasheet
AT88SC-DK1 AT88SC-DK1 AT88SC-DK1 (pdf)
PDF Datasheet Preview
AT88SC-DK1 WELCOME AND QUICK START GUIDE

Dear Valued Customer, Thank you for choosing for your security needs. As you may already know, CryptoMemory provides low-cost powerful security for your product authentication and secure data storage needs. To ensure you have the most current information, we ask that you check the CryptoMemory product website at for any recent updates. We wish you an exciting development experience and ask that you do not hesitate to contact us at for any assistance we can provide.

Best regards, Your Atmel CryptoMemory Team

AT88SC-DK1 WELCOME AND QUICK START GUIDE
ÏÏÏÏ

Package Contents 1 AT88SC-DK1 CD 1 CryptoMemory adaptor board 1 tube of CryptoMemory samples 1 Black-Red patch cord 1 Green-Yellow patch cord

Everywhere You
ÏÏÏÏ

ADAPTING AT88SC-DK1 TO YOUR DEVELOPMENT SYSTEM
ÏÏÏÏ

System Requirements:
n 1 GPIO header pin for TWI clock, SCL. n 1 GPIO header pin for TWI data, SDA. n 1 header pin for power, VCC. n 1 header pin for ground, GND.
ÏÏÏÏ

Software Setup

Install contents of AT88SC-DK1 CD into your PC the README file for information on CryptoMemory Library Integration and Reference.
ÏÏÏÏ

Hardware Setup

STEP 1 Insert a CryptoMemory device into the SOIC socket

STEP 2 Connect Power and Ground wires

STEP 3 Connect Clock and Data wires

Align PIN 0 of the SOIC package towards the header-pins side of the adaptor board.

Use Black-Red patch cord
the double-header end of the Green-Yellow patch cord to the SCL-SDA header pins of the adaptor board. Align such that Green connects to SCL and Yellow connects to SDA.
the Green cord to your system TWI clock.
the Yellow cord to your system TWI data.

Use Green-Yellow patch cord
the double-header end of the Green-Yellow patch cord to the SCL-SDA header pins of the adaptor board. Align such that Green connects to SCL and Yellow connects to SDA.
the Green cord to your system TWI clock.
the Yellow cord to your system TWI data.
ÏÏÏÏ

Troubleshooting sure CryptoMemory is properly inserted and aligned in the SOIC socket. The
correct orientation places PIN 0 of the SOIC package towards the adaptor board header pins. When correctly oriented, holding the adaptor board with header pins towards self should present the marking texts on the CryptoMemory package right side up. Verify your hardware setup for accurate signal and power connections. Make sure VCC is connected to a high-drive power supply. sure your system meets pull-up resistor requirements on signal lines as defined in CryptoMemory datasheets sure to include noise filtering capacitors between Vcc and GND at the device level, if working with a noisy system. and Write CryptoMemory’s Memory Test Zone MTZ field to verify connectivity. MTZ is free of all security requirements at all times.
5253-SMEM-05/07
More datasheets: 60-7/8"X36YD | 60-3/4"X36YD | 60-1/2"X36YD | 600576 | 600575 | 9105 BK001 | 9105 BK002 | 383-2UYC/S530-A5 | 2540001 | J112


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT88SC-DK1 Datasheet file may be downloaded here without warranties.

Datasheet ID: AT88SC-DK1 519062