AT45DB011-XI

AT45DB011-XI Datasheet

The AT45DB011 is a 2.7-volt only, serial interface Flash memory suitable for in-system reprogramming. Its 1,081,344 bits of memory are organized as 512 pages of 264 bytes each. In addition to the main memory, the AT45DB011 also contains one SRAM data buffer of 264 bytes. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the DataFlash

Part	Datasheet
AT45DB011-XI	AT45DB011-XI (pdf)

Related Parts	Information
AT45DB011-JC	AT45DB011-JC
AT45DB011-JI	AT45DB011-JI
AT45DB011-SC	AT45DB011-SC
AT45DB011-SI	AT45DB011-SI
AT45DB011-XC	AT45DB011-XC

PDF Datasheet Preview
• Single 2.7V - 3.6V Supply • Serial Interface Architecture • Page Program Operation Single Cycle Reprogram Erase and Program 512 Pages 264 Bytes/Page Main Memory • Optional Page and Block Erase Operations • One 264-byte SRAM Data Buffer • Internal Program and Control Timer • Fast Page Program Time 7 ms Typical • 120 µs Typical Page to Buffer Transfer Time • Low Power Dissipation 4 mA Active Read Current Typical 2 µA CMOS Standby Current Typical • 13 MHz Max Clock Frequency • Hardware Data Protection Feature • Serial Peripheral Interface SPI Compatible Modes 0 and 3 • CMOS and TTL Compatible Inputs and Outputs • Commercial and Industrial Temperature Ranges The AT45DB011 is a 2.7-volt only, serial interface Flash memory suitable for in-system reprogramming. Its 1,081,344 bits of memory are organized as 512 pages of 264 bytes each. In addition to the main memory, the AT45DB011 also contains one SRAM data buffer of 264 bytes. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the DataFlash Pin Configurations SOIC continued Pin Name CS SCK SI Function Chip Select Serial Clock Serial Input SI 1 SCK 2 RESET 3 8 SO 7 GND 6 VCC 5 WP Serial Output Hardware Page Write Protect Pin RESET Chip Reset RDY/BUSY Ready/Busy PLCC TSSOP Top View Type 1 4 CS 3 NC 2 NC 1 GND 32 VCC 31 NC 30 NC SCK 5 SI 6 SO 7 NC 8 NC 9 NC 10 NC 11 NC 12 NC 13 29 WP 28 RESET 27 RDY/BUSY 26 NC 25 NC 24 NC 23 NC 22 NC 21 NC RDY/BUSY 1 RESET 2 WP 3 VCC 4 GND 5 SCK 6 SO 7 14 CS 13 NC 12 NC 11 NC 10 NC 9 NC 8 SI NC 14 NC 15 DC 16 DC 17 NC 18 NC 19 NC 20 Note PLCC package pins 16 and 17 are DON’T CONNECT 1-megabit 2.7-volt Only Serial AT45DB011 Recommend using AT45DB011B for new designs. AT45DB011 Preliminary 16Megabit 2.7-volt Only Serial DataFlash uses a serial interface to sequentially access its data. The simple serial interface facilitates hardware layout, increases system reliability, minimizes switching noise, and reduces package size and active pin count. The device is optimized for use in many commercial and industrial applications where high density, low pin count, low voltage, and low power are essential. Typical applications for the DataFlash are digital voice storage, image storage, and data storage. The device operates at clock frequencies up to 13 MHz with a typical active read current consumption of 4 mA. To allow for simple in-system reprogrammability, the AT45DB011 does not require high input voltages for programming. The device operates from a single power supply, 2.7V to 3.6V, for both the program and read operations. The AT45DB011 is enabled through the chip select pin CS and accessed via a three-wire interface consisting of the Serial Input SI , Serial Output SO , and the Serial Clock SCK . All programming cycles are self-timed, and no separate erase cycle is required before programming. Block Diagram FLASH MEMORY ARRAY PAGE 264 BYTES BUFFER 264 BYTES SCK CS RESET VCC GND RDY/BUSY I/O INTERFACE Ordering Information fSCK MHz ICC mA Active Standby Ordering Code AT45DB011-JC AT45DB011-SC AT45DB011-XC AT45DB011-JI AT45DB011-SI AT45DB011-XI Package 32J 8S2 14X 32J 8S2 14X Operation Range Commercial 0°C to 70°C Industrial -40°C to 85°C 32J 8S2 14X Package Type 32-lead, Plastic J-leaded Chip Carrier PLCC 8-lead, Wide, Plastic Gull Wing Small Outline EIAJ SOIC 14-lead, Wide, Plastic Thin Shrink Small Outline Package TSSOP AT45DB011 AT45DB011 Packaging Information 32J, 32-lead, Plastic J-leaded Chip Carrier PLCC Dimensions in Inches and Millimeters JEDEC STANDARD MS-016 AE 8S2, 8-lead, Wide, Plastic Gull Wing Small Outline EIAJ SOIC Dimensions in Inches and Millimeters X PIN NO. 1 IDENTIFY AT CONTACT POINTS X MAX 3X 14X, 14-lead, Wide, Thin Shrink Small Outline Package TSSOP Dimensions in Millimeters and Inches * PIN 1 INDEX MARK PIN 1 SEATING PLANE *Controlling dimension millimeters Atmel Headquarters Corporate Headquarters 2325 Orchard Parkway San Jose, CA 95131 TEL 408 441-0311 FAX 408 487-2600 Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL 41 26-426-5555 FAX 41 26-426-5500 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL 852 2721-9778 FAX 852 2722-1369 Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL 81 3-3523-3551 FAX 81 3-3523-7581 Atmel Operations Atmel Colorado Springs 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 719 576-3300 FAX 719 540-1759 Atmel Rousset Zone Industrielle 13106 Rousset Cedex France TEL 33 4-4253-6000 FAX 33 4-4253-6001 Atmel Smart Card ICs Scottish Enterprise Technology Park East Kilbride, Scotland G75 0QR TEL 44 1355-357-000 FAX 44 1355-242-743 Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex France TEL 33 4-7658-3000 FAX 33 4-7658-3480 Fax-on-Demand North America 1- 800 292-8635 International 1- 408 441-0732 e-mail Web Site BBS 1- 408 436-4309 Atmel Corporation Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. Marks bearing and/or are registered trademarks and trademarks of Atmel Corporation.

PDF Datasheet Preview

• Single 2.7V - 3.6V Supply
• Serial Interface Architecture
• Page Program Operation

Single Cycle Reprogram Erase and Program 512 Pages 264 Bytes/Page Main Memory
• Optional Page and Block Erase Operations
• One 264-byte SRAM Data Buffer
• Internal Program and Control Timer
• Fast Page Program Time 7 ms Typical
• 120 µs Typical Page to Buffer Transfer Time
• Low Power Dissipation 4 mA Active Read Current Typical
2 µA CMOS Standby Current Typical
• 13 MHz Max Clock Frequency
• Hardware Data Protection Feature
• Serial Peripheral Interface SPI Compatible Modes 0 and 3
• CMOS and TTL Compatible Inputs and Outputs
• Commercial and Industrial Temperature Ranges

The AT45DB011 is a 2.7-volt only, serial interface Flash memory suitable for in-system reprogramming. Its 1,081,344 bits of memory are organized as 512 pages of 264 bytes each. In addition to the main memory, the AT45DB011 also contains one SRAM data buffer of 264 bytes. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the DataFlash

Pin Configurations

SOIC
continued

Pin Name CS SCK SI

Function Chip Select Serial Clock Serial Input

SI 1 SCK 2 RESET 3
8 SO 7 GND 6 VCC 5 WP

Serial Output

Hardware Page Write Protect Pin

RESET

Chip Reset

RDY/BUSY Ready/Busy

PLCC

TSSOP Top View Type 1
4 CS 3 NC 2 NC 1 GND 32 VCC 31 NC 30 NC

SCK 5 SI 6

SO 7 NC 8 NC 9 NC 10 NC 11 NC 12 NC 13
29 WP 28 RESET 27 RDY/BUSY 26 NC 25 NC 24 NC 23 NC 22 NC 21 NC

RDY/BUSY 1 RESET 2 WP 3 VCC 4 GND 5 SCK 6 SO 7
14 CS 13 NC 12 NC 11 NC 10 NC
9 NC 8 SI

NC 14 NC 15 DC 16 DC 17 NC 18 NC 19 NC 20

Note PLCC package pins 16 and 17 are DON’T CONNECT
1-megabit 2.7-volt Only Serial AT45DB011

Recommend using AT45DB011B for new designs.

AT45DB011 Preliminary 16Megabit 2.7-volt Only Serial DataFlash
uses a serial interface to sequentially access its data. The simple serial interface facilitates hardware layout, increases system reliability, minimizes switching noise, and reduces package size and active pin count. The device is optimized for use in many commercial and industrial applications where high density, low pin count, low voltage, and low power are essential. Typical applications for the DataFlash are digital voice storage, image storage, and data storage. The device operates at clock frequencies up to 13 MHz with a typical active read current consumption of 4 mA.

To allow for simple in-system reprogrammability, the AT45DB011 does not require high input voltages for programming. The device operates from a single power supply, 2.7V to 3.6V, for both the program and read operations. The AT45DB011 is enabled through the chip select pin CS and accessed via a three-wire interface consisting of the Serial Input SI , Serial Output SO , and the Serial Clock SCK .

All programming cycles are self-timed, and no separate erase cycle is required before programming.

Block Diagram

FLASH MEMORY ARRAY

PAGE 264 BYTES

BUFFER 264 BYTES

SCK CS

RESET VCC GND

RDY/BUSY

I/O INTERFACE
Ordering Information
fSCK MHz

ICC mA

Active

Standby
Ordering Code

AT45DB011-JC AT45DB011-SC AT45DB011-XC

AT45DB011-JI AT45DB011-SI AT45DB011-XI

Package
32J 8S2 14X
32J 8S2 14X

Operation Range Commercial 0°C to 70°C

Industrial -40°C to 85°C
32J 8S2 14X

Package Type 32-lead, Plastic J-leaded Chip Carrier PLCC 8-lead, Wide, Plastic Gull Wing Small Outline EIAJ SOIC 14-lead, Wide, Plastic Thin Shrink Small Outline Package TSSOP

AT45DB011

AT45DB011

Packaging Information
32J, 32-lead, Plastic J-leaded Chip Carrier PLCC Dimensions in Inches and Millimeters

JEDEC STANDARD MS-016 AE
8S2, 8-lead, Wide, Plastic Gull Wing Small Outline EIAJ SOIC Dimensions in Inches and Millimeters

X PIN NO. 1 IDENTIFY

AT CONTACT POINTS

X MAX 3X
14X, 14-lead, Wide, Thin Shrink Small Outline Package TSSOP Dimensions in Millimeters and Inches *

PIN 1

INDEX MARK

PIN 1

SEATING PLANE
*Controlling dimension millimeters

Atmel Headquarters

Corporate Headquarters 2325 Orchard Parkway San Jose, CA 95131 TEL 408 441-0311 FAX 408 487-2600

Europe Atmel SarL Route des Arsenaux 41 Casa Postale 80 CH-1705 Fribourg Switzerland TEL 41 26-426-5555 FAX 41 26-426-5500

Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL 852 2721-9778 FAX 852 2722-1369

Japan Atmel Japan K.K. 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL 81 3-3523-3551 FAX 81 3-3523-7581

Atmel Operations

Atmel Colorado Springs 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 719 576-3300 FAX 719 540-1759

Atmel Rousset Zone Industrielle 13106 Rousset Cedex France TEL 33 4-4253-6000 FAX 33 4-4253-6001

Atmel Smart Card ICs Scottish Enterprise Technology Park East Kilbride, Scotland G75 0QR TEL 44 1355-357-000 FAX 44 1355-242-743

Atmel Grenoble Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex France TEL 33 4-7658-3000 FAX 33 4-7658-3480

Fax-on-Demand North America 1- 800 292-8635 International 1- 408 441-0732
e-mail

Web Site

BBS 1- 408 436-4309

Atmel Corporation Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems.

Marks bearing and/or are registered trademarks and trademarks of Atmel Corporation.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT45DB011-XI Datasheet file may be downloaded here without warranties.

Datasheet ID: AT45DB011-XI 519038