AT30TS750-SS8-T

AT30TS750-SS8-T Datasheet


Atmel AT30TS750

Part Datasheet
AT30TS750-SS8-T AT30TS750-SS8-T AT30TS750-SS8-T (pdf)
Related Parts Information
AT30TS750-SS8-B AT30TS750-SS8-B AT30TS750-SS8-B
AT30TS750-XM8-B AT30TS750-XM8-B AT30TS750-XM8-B
AT30TS750-XM8-T AT30TS750-XM8-T AT30TS750-XM8-T
AT30TS750-MA8-T AT30TS750-MA8-T AT30TS750-MA8-T
PDF Datasheet Preview
Atmel AT30TS750
9- to 12-bit Selectable, ±0.5°C Accurate Digital Temperature Sensor with Nonvolatile Registers

DATASHEET

See Applicable Errata in Section

Single 2.7V - 5.5V supply Measures temperature from -55C to +125C Highly accurate temperature measurements requiring no external components
±0.5°C accuracy typical over the 0C to +85C range ±1.0°C accuracy typical over the -25C to +105C range ±2.0°C accuracy typical over the -40C to +125C range User-configurable resolution 9 to 12 bits 0.5C to 0.0625C User-configurable high and low temperature limits Nonvolatile registers to retain user-configured or pre-defined power-up defaults Register locking to prevent erroneous misconfiguration Register lockdown for permanent, non-changeable device configuration ALERT output pin for indicating temperature alarms 2-wire I2C and SMBus compatible serial interface Supports SMBus Timeout Supports SMBus Alert and Alert Response Address ARA Selectable addressing allows up to eight devices on the same bus Built-in noise suppression filtering for clock and data input signals Low power dissipation 75uA active current typical during temperature measurements Shutdown mode to minimize power consumption 1uA shutdown current typical One-shot mode for single temperature measurement while in Shutdown mode Pin and software compatible to industry-standard LM75-type devices Industry standard green Pb/Halide-free/RoHS compliant package options 8-lead SOIC 150-mil 8-lead MSOP 3 x 3mm 8-pad Ultra Thin DFN UDFN - 2 x 3 x 0.6mm

Table of Contents

Description 4

Pin Descriptions and Pinouts 5

Block Diagram 6

Device Communication 7

Start Condition 7 Stop Condition. 7 Acknowledge ACK 7 No-Acknowledge NACK 8

Device Operation 9

Temperature Measurements. 9 Temperature Alarm 10

Fault Tolerance Limits 10 Comparator Mode 11 Interrupt Mode 12 Shutdown Mode 13 One-shot Mode 13

Registers 14

Pointer Register 14 Temperature Register 16 Configuration Register 18

OS Bit 19 R1:R0 Bits 19 FT1:FT0 Bits 20 POL Bit 20 CMP/INT Bit 20 SD Bit 20 NVRBSY 21 Nonvolatile Configuration Register 22 NVR1 NVR0 Bits 23 NVFT1:NVFT0 Bits 24 NVPOL Bit 24 NVCMP/INT Bit 24 NVSD Bit 24 RLCKDWN 24 RLCK 25 TLOW and THIGH Limit Registers 26 Nonvolatile TLOW and THIGH Limit Registers 28

Register Locking 30

Operations Allowed During Nonvolatile Busy Status 31

Other Commands 32

Copy Nonvolatile Registers to Volatile Registers 32 Copy Volatile Registers to Nonvolatile Registers 33

Atmel AT30TS750 [DATASHEET]

SMBus Features and I2C General Call 34

SMBus Alert 34 SMBus Timeout. 35 General Call 35

Electrical Specifications 36

Absolute Maximum Ratings* 36 DC and AC Operating Range 36 DC Characteristics 37 Temperature Sensor Accuracy and Conversion Characteristics 38 AC Characteristics 38 Nonvolatile Register Characteristics 39 Power-up Conditions. 39 Pin Capacitance 40 Input Test Waveforms and Measurement Levels 40 Output Test Load 40
Ordering Information 41
Atmel Ordering Code Detail 41 Green Package Options Pb/Halide-free/RoHS Compliant 41

Part Marking Detail 42

Packaging Information 43
8S1 8-lead JEDEC SOIC 43 8XM 8-lead MSOP 44 8MA2 8-pad UDFN 45

Errata 46

DC Characteristics 46 Temperature Sensor Accuracy Characteristics. 47 Fault Counter 48 ALERT Pin 48

Atmel AT30TS750 [DATASHEET]

The AT30TS750 is a complete, precise temperature monitoring device designed for use in a variety of applications that require the measuring of local temperatures as an integral part of the system's function and/or reliability. The AT30TS750 device combines a high-precision digital temperature sensor, programmable high and low temperature alarms, and a 2-wire I2C and SMBus System Management Bus compatible serial interface into a single, compact package.

The temperature sensor can measure temperatures over the full -55°C to +125°C temperature range and has a typical accuracy as precise as ±0.5°C from 0°C to +85°C. The result of the digitized temperature measurements are stored in one of the AT30TS750's internal registers, which is readable at any time through the device's serial interface.

The AT30TS750 utilizes flexible, user-programmable internal registers to configure the temperature sensor's performance and response to high and low temperature conditions. The device also contains a set of Nonvolatile Registers to retain the configuration and temperature limit settings even after the device has been power cycled, thereby eliminating the need for the device to be reconfigured after each Power-up operation. This additional flexibility permits the device to run self-contained and not rely upon a host controller for device configuration.

A dedicated alarm output activates if the temperature measurement exceeds the user-defined temperature and fault count limits. To reduce current consumption and save power, the AT30TS750 features a Shutdown mode that turns off all internal circuitry except for the internal power-on reset POR and serial interface circuits. The device can also be configured to power-up in the Shutdown mode to ensure that the device remains in a low-power state until the user wishes to perform temperature measurements.

The AT30TS750 is factory-calibrated and requires no external components to measure temperature. With it’s flexibility and high-degree of accuracy, the AT30TS750 is ideal for extended temperature measurements in a wide variety of communication, computer, consumer, environmental, industrial, and instrumentation applications.

Atmel AT30TS750 [DATASHEET]

Pin Descriptions and Pinouts

Table Pin Description

Symbol Name and Function

Asserted State

Type

Serial Clock This pin is used to provide a clock to the device and is used to control
the flow of data to and from the device. Command and input data present on the SDA
pin is always latched in on the rising edge of SCL, while output data on the SDA pin is
always clocked out on the falling edge of SCL.

The SCL pin must either be forced high when the serial bus is idle or pulled-high using an external pull-up resistor.

Input

Serial Data The SDA pin is an open-drain bidirectional input/output pin used to serially transfer data to and from the device.

The SDA pin must be pulled-high using an external pull-up resistor and may be wire-ANDed with any number of other open-drain or open-collector pins from other devices on the same bus.

Input/Output

ALERT

Alert The ALERT pin is an open-drain output pin used to indicate when the temperature goes beyond the user-programmed temperature limits. The ALERT pin can be operated in one of two different modes Interrupt or Comparator mode as defined by the CMP/INT bit in the Configuration Register. The ALERT pin defaults to an active-low output upon device power-up or reset but can be reconfigured as an active-high output by setting the POL bit in the Configuration Register.

This pin can be wire-ANDed together with ALERT pins from other devices on the same
bus. When wire-ANDing pins together, the ALERT pin should be configured as an
active-low output so that when a single ALERT pin on the common alert bus goes
active, the entire common alert bus will go low and the host controller will be properly
notified since other ALERT pins that may be in the inactive-high state will not mask the
true alert signal. In an SMBus environment, the SMBus host can respond by sending
an SMBus ARA Alert Response Address command to determine which device on the

SMBus generated the alert signal.

The ALERT pin must be pulled-high using an external pull-up resistor even when it is not used. Care must also be taken to prevent this pin from being shorted directly to ground without a resistor at any time whether during testing or normal operation.

Output

A2-0

Address Inputs The A2-0 pins are used to select the device address and correspond
Ordering Information
Atmel Ordering Code Detail

Atmel Designator

Product Family 30TS = Digital Temperature Sensor

Device Type

AT 3 0 T S 7 5 0 - S 8 - B

Shipping Carrier Option B = Bulk tubes T = Tape and reel

Device Grade 8 = Green, NiPdAu lead finish,

Industrial high temperature range to +125°C Accuracy guaranteed

Package Option SS = 8-lead, wide SOIC XM = 8-lead, 3 x 3mm MSOP MA = 8-pad, 2 x 3 x 0.6mm

Green Package Options Pb/Halide-free/RoHS Compliant
Atmel Ordering Code

Package

Lead Pad Finish

Operating Voltage

Max. Freq. KHz

AT30TS750-SS8-B 8S1

AT30TS750-SS8-T

AT30TS750-XM8-B AT30TS750-XM8-T

NiPdAu
2.7V to 5.5V

AT30TS750-MA8-T
8MA2

Note:

The shipping carrier option code is not marked on the devices.

Operation Range

Industrial High Temperature -55°C to +125°C
8S1 8XM 8MA2

Package Type 8-lead, wide, Plastic Gull Wing Small Outline JEDEC SOIC 8-lead, 3 x 3 mm, Plastic Miniature Small Outline MSOP 8-pad, 2 x 3 x mm, Thermally Enhanced Plastic Ultra Thin Dual Flat No Lead UDFN

Atmel AT30TS750 [DATASHEET] 41

Part Marking Detail

Package Mark Contact:

Atmel AT30TS750 [DATASHEET] 42

Packaging Information
8S1 8-lead JEDEC SOIC

TOP VIEW

SIDE VIEW

Notes This drawing is for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.

END VIEW

COMMON DIMENSIONS Unit of Measure = mm

SYMBOL MIN

NOTE

Package Drawing Contact:
8S1, 8-lead Wide Body , Plastic Gull Wing Small Outline JEDEC SOIC

Atmel AT30TS750 [DATASHEET] 43
8XM 8-lead MSOP

Pin 1

CL E1 1

N/2 TIPS

TOP VIEW

SEE DETAIL "A"

BOTTOM VIEW
More datasheets: AK4617VQ | 3459 | HER303-T | HER305-T | HER302-T | HER301-T | HER304-T | AT30TS750-SS8-B | AT30TS750-XM8-B | AT30TS750-XM8-T


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT30TS750-SS8-T Datasheet file may be downloaded here without warranties.

Datasheet ID: AT30TS750-SS8-T 519010