AT27LV512A-90TU

AT27LV512A-90TU Datasheet


• Compatible with JEDEC Standard AT27C512R<br>• Low Power CMOS Operation

Part Datasheet
AT27LV512A-90TU AT27LV512A-90TU AT27LV512A-90TU (pdf)
Related Parts Information
AT27LV512A-90RU AT27LV512A-90RU AT27LV512A-90RU
PDF Datasheet Preview
• Fast Read Access Time 90 ns
• Dual Voltage Range Operation

Low Voltage Power Supply Range, 3.0V to 3.6V or Standard 5V ± 10% Supply Range
• Compatible with JEDEC Standard AT27C512R
• Low Power CMOS Operation
20 µA Max Less than 1 µA Typical Standby for VCC = 3.6V 29 mW Max Active at 5 MHz for VCC = 3.6V
• JEDEC Standard Packages 32-lead PLCC 28-lead SOIC 28-lead TSOP
• High Reliability CMOS Technology 2,000V ESD Protection 200 mA Latchup Immunity
• Rapid Programming Algorithm 100 µs/Byte Typical
• CMOS and TTL Compatible Inputs and Outputs JEDEC Standard for LVTTL
• Integrated Product Identification Code
• Industrial Temperature Range
• Green Pb/Halide-free Packaging Option
512K 64K x 8 Low Voltage OTP EPROM

AT27LV512A

The AT27LV512A is a high-performance, low-power, low-voltage 524,288-bit onetime programmable read-only memory OTP EPROM organized as 64K by 8 bits. It requires only one supply in the range of to 3.6V in normal read mode operation, making it ideal for fast, portable systems using battery power.

Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3.3V supply. At VCC = 3.0V, any byte can be accessed in less than 90 ns. With a typical power dissipation of only 18 mW at 5 MHz and VCC = 3.3V, the AT27LV512A consumes less than one fifth the power of a standard 5V EPROM. Standby mode supply current is typically less than 1 µA at 3.3V.

The AT27LV512A is available in industry-standard JEDEC-approved one-time programmable OTP plastic PLCC, SOIC, and TSOP packages. All devices feature two-line control CE, OE to give designers the flexibility to prevent bus contention.

The AT27LV512A operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts.

Atmel’s AT27LV512A has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 µs/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper programming algorithms and voltages. The AT27LV512A programs exactly the same way as a standard 5V AT27C512R and uses the same programming equipment.

Pin Configurations

Pin Name A0 - A15 O0 - O7 CE OE/VPP NC

Function Addresses Outputs Chip Enable Output Enable/ Program Supply No Connect
28-lead SOIC Top View

A15 1 A12 2

A7 3 A6 4 A5 5 A4 6 A3 7 A2 8 A1 9 A0 10 O0 11 O1 12 O2 13 GND 14
28 VCC 27 A14 26 A13 25 A8 24 A9 23 A11 22 OE/VPP 21 A10 20 CE 19 O7 18 O6 17 O5 16 O4 15 O3
32-lead PLCC Top View
28-lead TSOP Type 1 Top View

OE/VPP 1 A11 2 A9 3 A8 4 A13 5 A14 6 VCC 7 A15 8 A12 9 A7 10 A6 11 A5 12 A4 13 A3 14
28 A10 27 CE 26 O7 25 O6 24 O5 23 O4 22 O3 21 GND 20 O2 19 O1 18 O0 17 A0 16 A1 15 A2
4 A7 3 A12 2 A15 1 NC 32 VCC 31 A14 30 A13

A6 5 A5 6 A4 7 A3 8 A2 9 A1 10 A0 11 NC 12 O0 13
29 A8 28 A9 27 A11 26 NC 25 OE/VPP 24 A10 23 CE 22 O7 21 O6

O1 14 O2 15 GND 16 NC 17 O3 18 O4 19 O5 20

Note PLCC Package Pins 1 and 17 are Don’t Connect.
2 AT27LV512A

AT27LV512A

System Considerations

Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed datasheet limits, resulting in device non-conformance. At a minimum, a µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array.

Block Diagram

Absolute Maximum Ratings*

Temperature Under Bias.................................. -40°C to +85°C

Storage Temperature -65°C to +125°C

Voltage on Any Pin with Respect to Ground to +7.0V 1

Voltage on A9 with Respect to Ground to +14.0V 1

VPP Supply Voltage with Respect to Ground to +14.0V 1
*NOTICE:

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability

Note:
Ordering Information

Standard Package
tACC

ICC mA

Active Standby
Ordering Code AT27LV512A-90JI AT27LV512A-90RI AT27LV512A-90TI

Package
32J 28R 1 28T

Note:

Not recommended for new designs. Use Green package option.

Green Package Pb/Halide-free
tACC

ICC mA

Active Standby
Ordering Code

AT27LV512A-55JU

AT27LV512A-55RU

AT27LV512A-55TU

AT27LV512A-90JU

AT27LV512A-90RU

AT27LV512A-90TU

Note The 28-pin SOIC package is not recommended for new designs.

Package
32J 28R 1 28T
32J 28R 1 28T

AT27LV512A

Operation Range Industrial
-40°C to 85°C

Operation Range Industrial
-40°C to 85°C Industrial
-40°C to 85°C

Package Type
32-Lead, Plastic J-Leaded Chip Carrier PLCC
28-Lead, Wide, Plastic Gull Wing Small Outline SOIC
28-Lead, Thin Small Outline Package TSOP

Packaging Information
32J PLCC

PIN NO. 1 IDENTIFIER
e D1 D

B1 E2

A2 A1 A
0.51 0.020 MAX 3X

COMMON DIMENSIONS Unit of Measure = mm

This package conforms to JEDEC reference MS-016, Variation AE. Dimensions D1 and E1 do not include mold protrusion.

Allowable protrusion is mm per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. Lead coplanarity is mm maximum.

SYMBOL MIN NOM MAX NOTE

Note 2

Note 2
10/04/01

TITLE 2325 Orchard Parkway 32J, 32-lead, Plastic J-leaded Chip Carrier PLCC R San Jose, CA 95131
12 AT27LV512A
28R SOIC

AT27LV512A

PIN 1 e
0º ~ 8º
More datasheets: ES2B-13 | ES2A-13 | ES2C-13 | ES2DA-13 | ES2D-13 | SE9301 | SE9302 | SE9300 | MMBT2907A-7-F | MMBT2907A-7


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT27LV512A-90TU Datasheet file may be downloaded here without warranties.

Datasheet ID: AT27LV512A-90TU 518957