AT27LV010A-70VC

AT27LV010A-70VC Datasheet


Low Voltage Power Supply Range, 3.0V to 3.6V or Standard 5V ± 10% Supply Range<br>• Compatible with JEDEC Standard AT27C010<br>• Low Power CMOS Operation 20 µA max. less than 1 µA typical Standby for VCC = 3.6V 29 mW max. Active at 5 MHz for VCC = 3.6V<br>• JEDEC Standard Packages 32-Lead PLCC

Part Datasheet
AT27LV010A-70VC AT27LV010A-70VC AT27LV010A-70VC (pdf)
Related Parts Information
AT27LV010A-15TI AT27LV010A-15TI AT27LV010A-15TI
AT27LV010A-15TC AT27LV010A-15TC AT27LV010A-15TC
AT27LV010A-15JI AT27LV010A-15JI AT27LV010A-15JI
AT27LV010A-15JC AT27LV010A-15JC AT27LV010A-15JC
AT27LV010A-12VI AT27LV010A-12VI AT27LV010A-12VI
AT27LV010A-15VC AT27LV010A-15VC AT27LV010A-15VC
AT27LV010A-12TI AT27LV010A-12TI AT27LV010A-12TI
AT27LV010A-90VI AT27LV010A-90VI AT27LV010A-90VI
AT27LV010A-12TC AT27LV010A-12TC AT27LV010A-12TC
AT27LV010A-12JI AT27LV010A-12JI AT27LV010A-12JI
AT27LV010A-12VC AT27LV010A-12VC AT27LV010A-12VC
AT27LV010A-70JI AT27LV010A-70JI AT27LV010A-70JI
AT27LV010A-15VI AT27LV010A-15VI AT27LV010A-15VI
AT27LV010A-70JC AT27LV010A-70JC AT27LV010A-70JC
AT27LV010A-70VI AT27LV010A-70VI AT27LV010A-70VI
AT27LV010A-70TI AT27LV010A-70TI AT27LV010A-70TI
AT27LV010A-90TI AT27LV010A-90TI AT27LV010A-90TI
AT27LV010A-90TC AT27LV010A-90TC AT27LV010A-90TC
AT27LV010A-90JI AT27LV010A-90JI AT27LV010A-90JI
AT27LV010A-90VC AT27LV010A-90VC AT27LV010A-90VC
AT27LV010A-70TC AT27LV010A-70TC AT27LV010A-70TC
AT27LV010A-12JC AT27LV010A-12JC AT27LV010A-12JC
AT27LV010A-90JC AT27LV010A-90JC AT27LV010A-90JC
PDF Datasheet Preview
• Fast Read Access Time - 70 ns
• Dual Voltage Range Operation

Low Voltage Power Supply Range, 3.0V to 3.6V or Standard 5V ± 10% Supply Range
• Compatible with JEDEC Standard AT27C010
• Low Power CMOS Operation 20 µA max. less than 1 µA typical Standby for VCC = 3.6V 29 mW max. Active at 5 MHz for VCC = 3.6V
• JEDEC Standard Packages 32-Lead PLCC
32-Lead TSOP 8 x 20 mm
32-Lead VSOP 8 x 14 mm
• High Reliability CMOS Technology
2,000V ESD Protection
200 mA Latchup Immunity
• Rapid Programming Algorithm - 100 µs/byte typical
• CMOS and TTL Compatible Inputs and Outputs

JEDEC Standard for LVTTL
• Integrated Product Identification Code
• Commercial and Industrial Temperature Ranges

The AT27LV010A is a high performance, low power, low voltage 1,048,576-bit one-
time programmable read only memory OTP EPROM organized as 128K by 8 bits. It
requires only one supply in the range of 3.0V to 3.6V in normal read mode operation,
making it ideal for fast, portable systems using battery power.
continued
1-Megabit 128K x 8 Low Voltage OTP EPROM

AT27LV010A

O1 14 O2 15 GND 16 O3 17 O4 18 O5 19 O6 20

Pin Configurations

Pin Name A0 - A16 O0 - O7 CE OE PGM NC

Function Addresses Outputs Chip Enable Output Enable Program Strobe No Connect

PLCC Top View
4 A12 3 A15 2 A16 1 VPP 32 VCC 31 PGM 30 NC

A7 5 A6 6 A5 7 A4 8 A3 9 A2 10 A1 11 A0 12 O0 13
29 A14 28 A13 27 A8 26 A9 25 A11 24 OE 23 A10 22 CE 21 O7

TSOP/VSOP Top View Type 1

A11 1 A9 2 A8 3

A13 4 A14 5 NC 6 PGM 7 VCC 8 VPP 9 A16 10 A15 11 A12 12

A7 13 A6 14 A5 15 A4 16
32 OE 31 A10 30 CE 29 O7 28 O6 27 O5 26 O4 25 O3 24 GND 23 O2 22 O1 21 O0 20 A0 19 A1 18 A2 17 A3

Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3.3V supply. At VCC = 3.0V, any byte can be accessed in less than 70 ns. With a typical power dissipation of only 18 mW at 5 MHz and VCC = 3.3V, the AT27LV010A consumes less than one fifth the power of a standard 5V EPROM. Standby mode supply current is typically less than 1 µA at 3.3V.

The AT27LV010A is available in industry standard JEDECapproved one-time programmable OTP plastic PLCC and TSOP packages. All devices feature two-line control CE, OE to give designers the flexibility to prevent bus contention.

The AT27LV010A operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts.

Atmel’s AT27LV010A has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 µs/byte. The Integrated

Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. The AT27LV010A programs exactly the same way as a standard 5V AT27C010 and uses the same programming equipment.

System Considerations

Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array.

Block Diagram

AT27LV010A

AT27LV010A

Absolute Maximum Ratings*

Temperature Under Bias -40°C to +85°C

Storage Temperature -65°C to +125°C

Voltage on Any Pin with Respect to Ground to +7.0V 1
Ordering Information
tACC

ICC mA VCC = 3.6V

Active Standby
Ordering Code AT27LV010A-70JC AT27LV010A-70TC AT27LV010A-70VC AT27LV010A-70JI AT27LV010A-70TI AT27LV010A-70VI AT27LV010A-90JC AT27LV010A-90TC AT27LV010A-90VC AT27LV010A-90JI AT27LV010A-90TI AT27LV010A-90VI AT27LV010A-12JC AT27LV010A-12TC AT27LV010A-12VC AT27LV010A-12JI AT27LV010A-12TI AT27LV010A-12VI AT27LV010A-15JC AT27LV010A-15TC AT27LV010A-15VC AT27LV010A-15JI AT27LV010A-15TI AT27LV010A-15VI

Package 32J 32T 32V 32J 32T 32V 32J 32T 32V 32J 32T 32V 32J 32T 32V 32J 32T 32V 32J 32T 32V 32J 32T 32V

Operation Range Commercial 0°C to 70°C

Industrial -40°C to 85°C

Commercial 0°C to 70°C

Industrial -40°C to 85°C

Commercial 0°C to 70°C

Industrial -40°C to 85°C

Commercial 0°C to 70°C

Industrial -40°C to 85°C
32J 32T 32V

Package Type 32-Lead, Plastic J-Leaded Chip Carrier PLCC 32-Lead, Plastic Thin Small Outline Package TSOP 8 x 20 mm 32-Lead, Plastic Thin Small Outline Package VSOP 8 x 14 mm

AT27LV010A

AT27LV010A

Packaging Information
32J, 32-Lead, Plastic J-Leaded Chip Carrier PLCC Dimensions in Inches and Millimeters

JEDEC STANDARD MS-016 AE

X PIN NO. 1 IDENTIFY

AT CONTACT POINTS

X MAX 3X
32V, 32-Lead, Plastic Thin Small Outline Package VSOP Dimensions in Inches and Millimeters

JEDEC OUTLINE MO-142 BA
32T, 32-Lead, Plastic Thin Small Outline Package TSOP Dimensions in Millimeters and Inches *

JEDEC OUTLINE MO-142 BD

INDEX MARK
*Controlling dimension millimeters

INDEX MARK

Atmel Headquarters

Atmel Operations

Corporate Headquarters 2325 Orchard Parkway San Jose, CA 95131 TEL 408 441-0311 FAX 408 487-2600

Atmel Colorado Springs 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 719 576-3300 FAX 719 540-1759

Europe Atmel U.K., Ltd. Coliseum Business Centre Riverside Way Camberley, Surrey GU15 3YL England TEL 44 1276-686677 FAX 44 1276-686697

Atmel Rousset Zone Industrielle 13106 Rousset Cedex, France TEL 33 4 42 53 60 00 FAX 33 4 42 53 60 01

Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon, Hong Kong TEL 852 27219778 FAX 852 27221369

Japan Atmel Japan K.K. Tonetsu Shinkawa Bldg., 9F 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL 81 3-3523-3551 FAX 81 3-3523-7581

Fax-on-Demand North America 1- 800 292-8635

International 1- 408 441-0732
e-mail

Web Site

BBS 1- 408 436-4309

Atmel Corporation Atmel Cor poration makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s website. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual proper ty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems.
More datasheets: AT27LV010A-90VI | AT27LV010A-12TC | AT27LV010A-12JI | AT27LV010A-12VC | AT27LV010A-70JI | AT27LV010A-15VI | AT27LV010A-70JC | AT27LV010A-70VI | AT27LV010A-70TI | AT27LV010A-90TI


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived AT27LV010A-70VC Datasheet file may be downloaded here without warranties.

Datasheet ID: AT27LV010A-70VC 518949