MAX9622AXK+

MAX9622AXK+ Datasheet

MAX9622

Part	Datasheet
MAX9622AXK+	MAX9622AXK+ (pdf)

PDF Datasheet Preview
MAX9622 EVALUATION KIT AVAILABLE Precision, High-Bandwidth Op Amp The MAX9622 op amp features rail-to-rail output and 50MHz GBW at just 1mA supply current. At power-up, this device autocalibrates its input offset voltage to less than 100µV. It operates from a single-supply voltage of 2.0V to 5.25V. The MAX9622 is available in a tiny 2mm x 2mm, 5-pin SC70 package and is rated over the -40°C to +125°C automotive temperature range. ●● Power Modules ●● ADC Drivers for Industrial Systems ●● Instrumentation ●● Filters ●● 50MHz UGBW ●● Low Input Voltage Offset Voltage 100uV max ●● Input Common-Mode Voltage Range Extends Below Ground ●● Wide 2.0V to 5.25V Supply Range ●● Low 1mA Supply Current Ordering Information PART TEMP RANGE PINPACKAGE MAX9622AXK+T -40°C to +125°C 5 SC70 +Denotes a lead Pb -free/RoHS-compliant package. T = Tape and reel. TOP MARK Typical Application Circuit INPUT 5.5kI 4.7nF 47pF VCC/2 MAX9622 OUTPUT USING THE MAX9622 AS A LOWPASS BESSEL FILTER CORNER FREQUENCY = 100kHz . MAX9622 Precision, High-Bandwidth Op Amp Absolute Maximum Ratings Supply Voltage VCC to GND ...............................-0.3V to +5.5V All Other Pins................................ GND - 0.3V to VCC + 0.3V Short-Circuit Duration to GND or VCC..................................... 1s Continuous Input Current any Thermal Limits Note 1 Continuous Power Dissipation TA = +70°C 5-Pin SC70 derate 3.1mW/°C above +70°C ...........245.4mW Operating Temperature Range.......................... -40°C to +125°C Junction Storage Temperature Range............................. -65°C to +150°C Lead Temperature soldering, 10s .................................. +300°C Soldering Temperature Note 1 Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics VCC = 5V, VIN+ = VIN- = 0V, RL = 10kΩ to VCC/2, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C. Note 2 PARAMETER CONDITIONS POWER SUPPLY Supply Voltage Range VCC Guaranteed by PSRR Supply Current No load TA = +25°C -40°C TA +125°C Power-Supply Rejection Ratio PSRR TA = +25°C -40°C TA +125°C Power-Up Time DC SPECIFICATIONS Input Offset Voltage After power-up autocalibration -40°C TA +125°C For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values min and max limits shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 2015 Maxim Integrated Products, Inc. 10

PDF Datasheet Preview

MAX9622

EVALUATION KIT AVAILABLE

Precision, High-Bandwidth Op Amp

The MAX9622 op amp features rail-to-rail output and 50MHz GBW at just 1mA supply current. At power-up, this device autocalibrates its input offset voltage to less than 100µV. It operates from a single-supply voltage of 2.0V to 5.25V.

The MAX9622 is available in a tiny 2mm x 2mm, 5-pin SC70 package and is rated over the -40°C to +125°C automotive temperature range.
●● Power Modules ●● ADC Drivers for Industrial Systems ●● Instrumentation ●● Filters
●● 50MHz UGBW
●● Low Input Voltage Offset Voltage 100uV max
●● Input Common-Mode Voltage Range Extends Below Ground
●● Wide 2.0V to 5.25V Supply Range
●● Low 1mA Supply Current
Ordering Information

PART

TEMP RANGE

PINPACKAGE

MAX9622AXK+T -40°C to +125°C 5 SC70
+Denotes a lead Pb -free/RoHS-compliant package. T = Tape and reel.

TOP MARK

Typical Application Circuit

INPUT
5.5kI 4.7nF
47pF

VCC/2

MAX9622

OUTPUT

USING THE MAX9622 AS A LOWPASS BESSEL FILTER CORNER FREQUENCY = 100kHz .

MAX9622

Precision, High-Bandwidth Op Amp

Absolute Maximum Ratings

Supply Voltage VCC to GND ...............................-0.3V to +5.5V All Other Pins................................ GND - 0.3V to VCC + 0.3V Short-Circuit Duration to GND or VCC..................................... 1s Continuous Input Current any Thermal Limits Note 1 Continuous Power Dissipation TA = +70°C
5-Pin SC70 derate 3.1mW/°C above +70°C ...........245.4mW

Operating Temperature Range.......................... -40°C to +125°C Junction Storage Temperature Range............................. -65°C to +150°C Lead Temperature soldering, 10s .................................. +300°C Soldering Temperature

Note 1 Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Electrical Characteristics

VCC = 5V, VIN+ = VIN- = 0V, RL = 10kΩ to VCC/2, TA = -40°C to +125°C, unless otherwise noted. Typical values are at TA = +25°C. Note 2

PARAMETER

CONDITIONS

POWER SUPPLY

Supply Voltage Range

VCC Guaranteed by PSRR

Supply Current

No load

TA = +25°C -40°C TA +125°C

Power-Supply Rejection Ratio

PSRR TA = +25°C
-40°C TA +125°C

Power-Up Time

DC SPECIFICATIONS

Input Offset Voltage

After power-up autocalibration
-40°C TA +125°C
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values min and max limits shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.

Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. 2015 Maxim Integrated Products, Inc. 10

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived MAX9622AXK+ Datasheet file may be downloaded here without warranties.

Datasheet ID: MAX9622AXK+ 647432