LTL42CW65AT

LTL42CW65AT Datasheet

Part No. LTL42CW65AT

Part	Datasheet
LTL42CW65AT	LTL42CW65AT (pdf)

PDF Datasheet Preview
LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only * LOW POWER CONSUMPTION. * HIGH EFFICIENCY. * VERSATILE MOUNTING ON P.C. BOARD OR PANEL. * I.C. COMPATIBLE/LOW CURRENT REQUIREMENTS. * POPULAR T1 DIAMETER. Package Dimensions Part No. LTL42CW65AT Lens Color Water Clear Emitted Color InGaN White NOTES All dimensions are in millimeters inches . Tolerance is unless otherwise noted. Protruded resin under flange is 1.0mm .04" max. Lead spacing is measured where the leads emerge from the package. Specifications are subject to change without notice. Part No. LTL42CW65AT BNS-OD-C131/A4 Page 1 of 7 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at MAXIMUM RATING 120 100 30 5 to + to + for 5 Seconds UNIT mW mA V Part No. LTL42CW65AT BNS-OD-C131/A4 Page 2 of 7 LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical / Optical Characteristics at PARAMETER Luminous Intensity Viewing Angle SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION 1150 2600 IF = 20mA Note 1,2,3 Iv spec. Table Note 4 Chromaticity Coordinates IF = 20mA Note 5 Hue Spec. Table & Chromaticity Diagram Forward Voltage IF = 20mA VR = 5V NOTE Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. The Iv guarantee should be added Iv classification code is marked on each packing bag. is the off-axis angle at which the luminous intensity is half the axial luminous intensity. The chromaticity coordinates x, y is derived from the 1931 CIE chromaticity diagram. Tolerance for each Color Coordinate bin is x, y Precautions in handling When soldering, leave 2mm of minimum clearance from the resin to the soldering point. Dipping the resin to solder must be avoided. Correcting the soldered position after soldering must be avoided. In soldering, do not apply any stress to the lead frame particularly when heated. Lead forming must be done before soldering. It is necessary to cut the lead frame at normal temperature. Caution in ESD Static Electricity and surge damages the LED. It is recommend using a wrist band or antielectrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. Part No. LTL42CW65AT BNS-OD-C131/A4

PDF Datasheet Preview

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only
* LOW POWER CONSUMPTION. * HIGH EFFICIENCY. * VERSATILE MOUNTING ON P.C. BOARD OR PANEL. * I.C. COMPATIBLE/LOW CURRENT REQUIREMENTS. * POPULAR T1 DIAMETER.

Package Dimensions

Part No. LTL42CW65AT

Lens Color Water Clear

Emitted Color InGaN White

NOTES All dimensions are in millimeters inches . Tolerance is unless otherwise noted. Protruded resin under flange is 1.0mm .04" max. Lead spacing is measured where the leads emerge from the package.

Specifications are subject to change without notice.

Part No. LTL42CW65AT BNS-OD-C131/A4

Page 1 of 7

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Absolute Maximum Ratings at

MAXIMUM RATING 120 100 30 5 to + to +
for 5 Seconds

UNIT mW mA V

Part No. LTL42CW65AT BNS-OD-C131/A4

Page 2 of 7

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Electrical / Optical Characteristics at

PARAMETER Luminous Intensity Viewing Angle

SYMBOL MIN. TYP. MAX. UNIT TEST CONDITION
1150 2600

IF = 20mA

Note 1,2,3

Iv spec. Table

Note 4

Chromaticity Coordinates

IF = 20mA Note 5

Hue Spec. Table & Chromaticity Diagram

Forward Voltage

IF = 20mA VR = 5V

NOTE Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve.

The Iv guarantee should be added

Iv classification code is marked on each packing bag. is the off-axis angle at which the luminous intensity is half the axial luminous intensity.

The chromaticity coordinates x, y is derived from the 1931 CIE chromaticity diagram. Tolerance for each Color Coordinate bin is x, y

Precautions in handling When soldering, leave 2mm of minimum clearance from the resin to the soldering point. Dipping the resin to solder must be avoided. Correcting the soldered position after soldering must be avoided. In soldering, do not apply any stress to the lead frame particularly when heated. Lead forming must be done before soldering. It is necessary to cut the lead frame at normal temperature.

Caution in ESD Static Electricity and surge damages the LED. It is recommend using a wrist band or antielectrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded.

Part No. LTL42CW65AT BNS-OD-C131/A4

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived LTL42CW65AT Datasheet file may be downloaded here without warranties.

Datasheet ID: LTL42CW65AT 646058