OP-4FW1-0441

OP-4FW1-0441 Datasheet

OP-4FM1-0442

Part	Datasheet
OP-4FW1-0441	OP-4FW1-0441 (pdf)

Related Parts	Information
DK-04D0-0395	DK-04D0-0395
OP-4FM1-0442	OP-4FM1-0442

PDF Datasheet Preview
construct the cable is to cut the two spare cables in half and stripping the wire lead ends about 3/8” 9mm on three of the halves. Plug the connectors of these three cable halves into the driver and each light engine assembly. Finally, connect the stripped leads as indicated in Figure Connecting Two Lamina AtlasTM White Light Engine Assemblies Figure Electrical Connections When using constant current LED drivers with high compliance voltage Advance, LED Works, etc. or a custom driver the output of the supply must be connected to the part before power is applied to the input of the supply. For more information refer to Lamina’s connection application note which can be found on the website at Assembly Recommendations Lamina’s AtlasTM Series Light Engines are designed for attachment to a heat sink with conductive epoxy, or screw down for flange mount devices with thermal grease in the joint. For attachment using screws a 4-40 UNC round head or metric equivalent M3 x cheese head screw, 18-8 SS is recommended. When mounting the light engine, position the four screws in the center of each of the four slots. Tighten the four screws eventually, first to about inch pounds 56 Newton-centimeters , and then tighten each to a maximum torque of 5 inch pounds 45 Newton-centimeter . Flatness requirement of the surface that the light engine is mounted to is inch/inch 1mm/meter . To prevent damage when using conductive epoxy do not use mounting screws. Notes This product uses silicone materials for superior optical performance. Do not expose the part to fluids that may react with silicone compounds. See Dow Chemical Form 45-0113D01, Silicone Fluid Resistance Guide. Ray trace models are available upon request. Lamina may make process or materials changes affecting the performance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to product supplied as samples or under prior orders. Warranty Statement Lamina Seller extends warranty on goods produced by the Seller for one 1 year from original date of shipment, that the goods sold hereunder are new and free from substantive defects in workmanship and materials. This warranty extends only to the Buyer and not to indirect purchasers or users. Seller’s liability under the foregoing warranty is limited to replacement of goods or repair of defects or refund of the purchase price at the seller’s sole option. The above warranty does not apply to defects resulting from the improper or inadequate maintenance, unauthorized modification, improper use or operation outside of Seller’s specifications for the product, abuse, neglect or accident. THE ABOVE WARRANTY IS EXCLUSIVE AND NO OTHER WARRANTY, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED. LAMINA SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Patents Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S. and/or International patents 5876536, 6709749 B, 595880, 6017642, 5565262, 5681444, 5653834, 5581876, AtlasTM White Developer Kit Bright. Compact. Reliable. changing At Lamina we’re the way you think about designing with LEDs. 120 Hancock Lane • Westampton, NJ 08060 • AtlasTM, NT-4000 White Developer Kits Lamina’s NEW AtlasTM, White Developer Kit series enable users to quickly discover the world of solid state lighting and realize the power of Lamina’s super-bright LED light engines. This kit is intended for the rapid evaluation and prototyping of LED lighting solutions based on the Lamina Warm White or Daylight White light engines. The kit is fully assembled and includes everything needed to jump start your design efforts. This comprehensive kit includes Warm White and Daylight White light engine Assemblies, wide and medium optics, a matched, commercially available, constant current driver prewired with AC and DC connections, AC plug adaptors and extra DC connectors. 3 789 Figure Overall Case Size - 12” x 9” x 3” AtlasTM, NT-4000 White Developer Kit - DK-04D0-0394 and DK-04D0-0395 Item Qty. Light Engine Assembly - Warm White 1 Light Source Soldered to EZ Connect with Heat Sink Light Engine Assembly - Daylight White 2 Light Source Soldered to EZ Connect with Heat Sink 3 Driver Sub Assembly, Advance 700mA DC/DC Cable Assembly, 2-pin, 200mm 1 prewired, 2 spare P/N 160-0245 160-0244 160-0213* 160-0214* 210-0145 Notes

PDF Datasheet Preview

construct the cable is to cut the two spare cables in half and stripping the wire lead ends about 3/8” 9mm on three of the halves. Plug the connectors of these three cable halves into the driver and each light engine assembly. Finally, connect the stripped leads as indicated in Figure

Connecting Two Lamina AtlasTM White Light Engine Assemblies

Figure

Electrical Connections

When using constant current LED drivers with high compliance voltage Advance, LED Works, etc. or a custom driver the output of the supply must be connected to the part before power is applied to the input of the supply. For more information refer to Lamina’s connection application note which can be found on the website at

Assembly Recommendations

Lamina’s AtlasTM Series Light Engines are designed for attachment to a heat sink with conductive epoxy, or screw down for flange mount devices with thermal grease in the joint. For attachment using screws a 4-40 UNC round head or metric equivalent M3 x cheese head screw, 18-8 SS is recommended. When mounting the light engine, position the four screws in the center of each of the four slots. Tighten the four screws eventually, first to about inch pounds 56 Newton-centimeters , and then tighten each to a maximum torque of 5 inch pounds 45 Newton-centimeter . Flatness requirement of the surface that the light engine is mounted to is inch/inch 1mm/meter . To prevent damage when using conductive epoxy do not use mounting screws.

Notes

This product uses silicone materials for superior optical performance. Do not expose the part to fluids that may react with silicone compounds. See Dow Chemical Form 45-0113D01, Silicone Fluid Resistance Guide.

Ray trace models are available upon request. Lamina may make process or materials changes affecting the performance or other
characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to product supplied as samples or under prior orders.

Warranty Statement

Lamina Seller extends warranty on goods produced by the Seller for one 1 year from original date of shipment, that the goods sold hereunder are new and free from substantive defects in workmanship and materials. This warranty extends only to the Buyer and not to indirect purchasers or users. Seller’s liability under the foregoing warranty is limited to replacement of goods or repair of defects or refund of the purchase price at the seller’s sole option. The above warranty does not apply to defects resulting from the improper or inadequate maintenance, unauthorized modification, improper use or operation outside of Seller’s specifications for the product, abuse, neglect or accident. THE ABOVE WARRANTY IS EXCLUSIVE AND NO OTHER WARRANTY, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED. LAMINA SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

Patents

Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S. and/or International patents 5876536, 6709749 B, 595880, 6017642, 5565262, 5681444, 5653834, 5581876,

AtlasTM White Developer Kit

Bright. Compact. Reliable.
changing At Lamina we’re
the way you think
about designing with LEDs.
120 Hancock Lane
• Westampton, NJ 08060
•

AtlasTM, NT-4000 White Developer Kits

Lamina’s NEW AtlasTM, White Developer Kit series enable users to quickly discover the world of solid state lighting and realize the power of Lamina’s super-bright LED light engines. This kit is intended for the rapid evaluation and prototyping of LED lighting solutions based on the Lamina Warm White or Daylight White light engines. The kit is fully assembled and includes everything needed to jump start your design efforts. This comprehensive kit includes Warm White and Daylight White light engine Assemblies, wide and medium optics, a matched, commercially available, constant current driver prewired with AC and DC connections, AC plug adaptors and extra DC connectors.
3 789

Figure

Overall Case Size - 12” x 9” x 3”

AtlasTM, NT-4000 White Developer Kit - DK-04D0-0394 and DK-04D0-0395

Item

Qty.

Light Engine Assembly - Warm White
1 Light Source Soldered to EZ Connect
with Heat Sink

Light Engine Assembly - Daylight White
2 Light Source Soldered to EZ Connect
with Heat Sink
3 Driver Sub Assembly, Advance 700mA

DC/DC Cable Assembly, 2-pin, 200mm 1 prewired, 2 spare

P/N 160-0245
160-0244
160-0213* 160-0214* 210-0145

Notes

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived OP-4FW1-0441 Datasheet file may be downloaded here without warranties.

Datasheet ID: OP-4FW1-0441 645400