C315C221K5G5TA7301

C315C221K5G5TA7301 Datasheet

C315

Part	Datasheet
C315C221K5G5TA7301	C315C221K5G5TA7301 (pdf)

Related Parts	Information
C315C279D2G5TA	C315C279D2G5TA
C315C479D2G5TA	C315C479D2G5TA
C315C109D2G5TA	C315C109D2G5TA
C315C223J5R5TA	C315C223J5R5TA
C315C102K2R5TA7301	C315C102K2R5TA7301
C315C689D2G5TA	C315C689D2G5TA
C315C224K1R5TA	C315C224K1R5TA
C315C104K1R5TA	C315C104K1R5TA
C315C103K1R5TA7301	C315C103K1R5TA7301
C315C224K1R5TA7303	C315C224K1R5TA7303
C315C474K5R5TA	C315C474K5R5TA
C315C103J5R5TA	C315C103J5R5TA
C315C684K5R5TA	C315C684K5R5TA
C315C569D2G5TA	C315C569D2G5TA
C315C229D2G5TA	C315C229D2G5TA
C315C102K5R5TA	C315C102K5R5TA
C315C339D2G5TA	C315C339D2G5TA
C315C102M5U5TA	C315C102M5U5TA

PDF Datasheet Preview
MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded styles include molded and conformally coated parts with axial and radial leads. However, the basic capacitor element is similar for all styles. It is called a chip and consists of formulated dielectric materials which have been cast into thin layers, interspersed with metal electrodes alternately exposed on opposite edges of the laminated structure. The entire structure is fired at high temperature to produce a monolithic block which provides high capacitance values in a small physical volume. After firing, conductive terminations are applied to opposite ends of the chip to make contact with the exposed electrodes. Termination materials and methods vary depending on the intended use. TEMPERATURE CHARACTERISTICS Ceramic dielectric materials can be formulated with a wide range of characteristics. The EIA standard for ceramic dielectric capacitors RS-198 divides ceramic dielectrics into the following classes: Class III General purpose capacitors, suitable for by-pass coupling or other applications in which dielectric losses, high insulation resistance and stability of capacitance characteristics are of little or no importance. Class III capacitors are similar to Class Class I Temperature compensating capacitors, II capacitors except for temperature characteristics, suitable for resonant circuit application or other appli- which are greater than ± Class III capacitors cations where high Q and stability of capacitance char- have the highest volumetric efficiency and poorest acteristics are required. Class I capacitors have stability of any type. predictable temperature coefficients and are not affected by voltage, frequency or time. They are made from materials which are not ferro-electric, yielding superior stability but low volumetric efficiency. Class I capacitors are the most stable type available, but have the lowest volumetric efficiency. KEMET leaded ceramic capacitors are offered in the three most popular temperature characteristics: C0G Class I, with a temperature coefficient of 0 ± 30 ppm per degree C over an operating temperature range of - 55°C to + 125°C Also known as “NP0” . Class II Stable capacitors, suitable for bypass X7R Class II, with a maximum capacitance or coupling applications or frequency discriminating change of ± 15% over an operating temperature circuits where Q and stability of capacitance char- range of - 55°C to + 125°C. acteristics are not of major importance. Class II Z5U Class III, with a maximum capacitance capacitors have temperature characteristics of ± 15% change of + 22% - 56% over an operating tem- or less. They are made from materials which are perature range of + 10°C to + 85°C. ferro-electric, yielding higher volumetric efficiency but less stability. Class II capacitors are affected by Specified electrical limits for these three temperature temperature, voltage, frequency and time. characteristics are shown in Table SPECIFIED ELECTRICAL LIMITS Parameter Dissipation Factor Measured at following conditions. C0G 1 kHz and 1 vrms if capacitance >1000pF 1 MHz and 1 vrms if capacitance 1000 pF X7R 1 kHz and 1 vrms* or if extended cap range vrms Z5U 1 kHz and vrms Dielectric Stength times rated DC voltage. Insulation Resistance IR At rated DC voltage, whichever of the two is smaller Temperature Characteristics Range, °C Capacitance Change without DC voltage * MHz and 1 vrms if capacitance 100 pF on military product. Temperature Characteristics Pass Subsequent IR Test ORDERING INFORMATION C 320 C 102 M 1 R 5 T A CERAMIC CASE SIZE See Table Above SPECIFICATION C Standard CAPACITANCE PICOFARAD CODE Expressed in picofarads pF . First two digits represent significant figures. Third digit specifies number of zeros. Use 9 for thru pF. Example 2.2pF = 229 CAPACITANCE TOLERANCE C0G C ±0.25pF D ±0.5pF F ±1%; G ±2% J ±5%, X7R K ±10% M ±20% P 0, -100%; Z -20,+80% Z5U M ±20% P 0, -100% Z -20,+80% FAILURE RATE A Not Applicable LEAD MATERIAL T 100% Tin Sn H 60/40% Tin/Lead SnPb INTERNAL CONSTRUCTION 5 Multilayer DIELECTRIC EIA Designation G C0G NP0 - Ultra Stable R X7R - Stable U Z5U - General Purpose RATED VOLTAGE DC D 1000 F 1500 1 100 G 2000 2 200 Z 2500 A 250 H 3000 C 500 For packaging information, see pages 47 and KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, 864 963-6300 CERAMIC CONFORMALLY COATED/RADIAL “STANDARD & HIGH VOLTAGE GOLD MAX” OPTIONAL CONFIGURATIONS BY LEAD SPACING The preferred lead wire configurations are shown on page However, additional configurations are available. All available options, including those on page 15, are shown below grouped by lead spacing. Lead Spacing ± C315 MAX. MAX. C316 MAX. MAX. C320 MAX. MAX. C324 MAX. MAX.

PDF Datasheet Preview

MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED

Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded styles include molded and conformally coated parts with axial and radial leads. However, the basic capacitor element is similar for all styles. It is called a chip and consists of formulated dielectric materials which have been cast into thin layers, interspersed with metal electrodes alternately exposed on opposite
edges of the laminated structure. The entire structure is fired at high temperature to produce a monolithic block which provides high capacitance values in a small physical volume. After firing, conductive terminations are applied to opposite ends of the chip to make contact with the exposed electrodes. Termination materials and methods vary depending on the intended use.

TEMPERATURE CHARACTERISTICS

Ceramic dielectric materials can be formulated with a wide range of characteristics. The EIA standard for ceramic dielectric capacitors RS-198 divides ceramic dielectrics into the following classes:

Class III General purpose capacitors, suitable for by-pass coupling or other applications in which dielectric losses, high insulation resistance and stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class

Class I Temperature compensating capacitors, II capacitors except for temperature characteristics,
suitable for resonant circuit application or other appli- which are greater than ± Class III capacitors
cations where high Q and stability of capacitance char- have the highest volumetric efficiency and poorest
acteristics are required. Class I capacitors have stability of any type.
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made from materials which are not ferro-electric, yielding superior stability but low volumetric efficiency. Class I capacitors are the most stable type available, but have the lowest volumetric efficiency.

KEMET leaded ceramic capacitors are offered in the three most popular temperature characteristics:

C0G Class I, with a temperature coefficient of 0 ± 30 ppm per degree C over an operating temperature range of - 55°C to + 125°C Also
known as “NP0” .

Class II Stable capacitors, suitable for bypass

X7R Class II, with a maximum capacitance
or coupling applications or frequency discriminating
change of ± 15% over an operating temperature
circuits where Q and stability of capacitance char-
range of - 55°C to + 125°C.
acteristics are not of major importance. Class II

Z5U Class III, with a maximum capacitance
capacitors have temperature characteristics of ± 15%
change of + 22% - 56% over an operating tem-
or less. They are made from materials which are
perature range of + 10°C to + 85°C.
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by Specified electrical limits for these three temperature
temperature, voltage, frequency and time.
characteristics are shown in Table

SPECIFIED ELECTRICAL LIMITS

Parameter

Dissipation Factor Measured at following conditions. C0G 1 kHz and 1 vrms if capacitance >1000pF 1 MHz and 1 vrms if capacitance 1000 pF X7R 1 kHz and 1 vrms* or if extended cap range vrms Z5U 1 kHz and vrms

Dielectric Stength times rated DC voltage.

Insulation Resistance IR At rated DC voltage, whichever of the two is smaller

Temperature Characteristics Range, °C Capacitance Change without DC voltage
* MHz and 1 vrms if capacitance 100 pF on military product.

Temperature Characteristics

Pass Subsequent IR Test
ORDERING INFORMATION

C 320 C 102 M 1 R 5 T A

CERAMIC

CASE SIZE See Table Above

SPECIFICATION C Standard

CAPACITANCE PICOFARAD CODE Expressed in picofarads pF . First two digits represent significant figures. Third digit specifies number of zeros. Use 9 for thru pF. Example 2.2pF = 229

CAPACITANCE TOLERANCE C0G C ±0.25pF D ±0.5pF F ±1%;

G ±2% J ±5%, X7R K ±10% M ±20% P 0, -100%;

Z -20,+80% Z5U M ±20% P 0, -100% Z -20,+80%

FAILURE RATE A Not Applicable

LEAD MATERIAL T 100% Tin Sn H 60/40% Tin/Lead SnPb INTERNAL CONSTRUCTION
5 Multilayer

DIELECTRIC EIA Designation G C0G NP0 - Ultra Stable R X7R - Stable U Z5U - General Purpose

RATED VOLTAGE DC

D 1000

F 1500
1 100

G 2000
2 200

Z 2500

A 250

H 3000

C 500

For packaging information, see pages 47 and

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, 864 963-6300

CERAMIC CONFORMALLY COATED/RADIAL
“STANDARD & HIGH VOLTAGE GOLD MAX”

OPTIONAL CONFIGURATIONS BY LEAD SPACING The preferred lead wire configurations are shown on page However, additional configurations are available. All available options, including those on page 15, are shown below grouped by lead spacing.

Lead Spacing ±

C315

MAX.

MAX.

C316

MAX.

MAX.

C320

MAX.

MAX.

C324

MAX.

MAX.

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived C315C221K5G5TA7301 Datasheet file may be downloaded here without warranties.

Datasheet ID: C315C221K5G5TA7301 644750