C062C394K5R5CA

C062C394K5R5CA Datasheet

Power dissipation has been empirically determined for two representative KEMET series C052 and C062. Power dissipation capability for various mounting configurations is shown in Table This table was extracted from Engineering Bulletin F-2013, which provides a more detailed treatment of this subject.

Part	Datasheet
C062C394K5R5CA	C062C394K5R5CA (pdf)

Related Parts	Information
C114C270K2G5CA	C114C270K2G5CA
C192C102G2G5CA	C192C102G2G5CA

PDF Datasheet Preview
MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded styles include molded and conformally coated parts with axial and radial leads. However, the basic capacitor element is similar for all styles. It is called a chip and consists of formulated dielectric materials which have been cast into thin layers, interspersed with metal electrodes alternately exposed on opposite edges of the laminated structure. The entire structure is fired at high temperature to produce a monolithic block which provides high capacitance values in a small physical volume. After firing, conductive terminations are applied to opposite ends of the chip to make contact with the exposed electrodes. Termination materials and methods vary depending on the intended use. TEMPERATURE CHARACTERISTICS Ceramic dielectric materials can be formulated with a wide range of characteristics. The EIA standard for ceramic dielectric capacitors RS-198 divides ceramic dielectrics into the following classes: Class III General purpose capacitors, suitable for by-pass coupling or other applications in which dielectric losses, high insulation resistance and stability of capacitance characteristics are of little or no importance. Class III capacitors are similar to Class Class I Temperature compensating capacitors, II capacitors except for temperature characteristics, suitable for resonant circuit application or other appli- which are greater than ± Class III capacitors cations where high Q and stability of capacitance char- have the highest volumetric efficiency and poorest acteristics are required. Class I capacitors have stability of any type. predictable temperature coefficients and are not affected by voltage, frequency or time. They are made from materials which are not ferro-electric, yielding superior stability but low volumetric efficiency. Class I capacitors are the most stable type available, but have the lowest volumetric efficiency. KEMET leaded ceramic capacitors are offered in the three most popular temperature characteristics: C0G Class I, with a temperature coefficient of 0 ± 30 ppm per degree C over an operating temperature range of - 55°C to + 125°C Also known as “NP0” . Class II Stable capacitors, suitable for bypass X7R Class II, with a maximum capacitance or coupling applications or frequency discriminating change of ± 15% over an operating temperature circuits where Q and stability of capacitance char- range of - 55°C to + 125°C. acteristics are not of major importance. Class II Z5U Class III, with a maximum capacitance capacitors have temperature characteristics of ± 15% change of + 22% - 56% over an operating tem- or less. They are made from materials which are perature range of + 10°C to + 85°C. ferro-electric, yielding higher volumetric efficiency but less stability. Class II capacitors are affected by Specified electrical limits for these three temperature temperature, voltage, frequency and time. characteristics are shown in Table SPECIFIED ELECTRICAL LIMITS Parameter Dissipation Factor Measured at following conditions. C0G 1 kHz and 1 vrms if capacitance >1000pF 1 MHz and 1 vrms if capacitance 1000 pF X7R 1 kHz and 1 vrms* or if extended cap range vrms Z5U 1 kHz and vrms Dielectric Stength times rated DC voltage. Insulation Resistance IR At rated DC voltage, whichever of the two is smaller Temperature Characteristics Range, °C Capacitance Change without DC voltage * MHz and 1 vrms if capacitance 100 pF on military product. Temperature Characteristics Pass Subsequent IR Test ORDERING INFORMATION C 052 C 102 K 2 R 5 T A CERAMIC CASE SIZE See Table Below SPECIFICATION C Standard CAPACITANCE PICOFARAD CODE Expressed in picofarads pF . First two digits represent significant figures. Third digit specifies number of zeros following except 9 indicates division by Examples µF = 100,000 pF = 104 and pF = See tables for standard values. CAPACITANCE TOLERANCE Standard Others M ±20% H ±3% K ±10% G ±2% J ±5% F ±1% D ±.5pF Standard tolerances for each Series are shown in the repetitive parts lists. FAILURE RATE A Not Applicable LEAD MATERIAL C 60/40 Tin/Lead SnPb T 100% Tin Sn C052, C062 only INTERNAL CONSTRUCTION 5 Multilayer TEMPERATURE CHARACTERISTIC KEMET Designator Cap. Change with Temp. EIA Equivalent Temp Range, °C Measured without DC Bias Voltage Ultra Stable NP0 -55 to +125° ±30 ppm/°C R Stable -55° to +125 ±15% WORKING VOLTAGE DC 2 200V 1 100V 5 50V Case Sizes Radial Axial C052 C114 C062

PDF Datasheet Preview

MULTILAYER CERAMIC CAPACITORS/AXIAL & RADIAL LEADED

Multilayer ceramic capacitors are available in a variety of physical sizes and configurations, including leaded devices and surface mounted chips. Leaded styles include molded and conformally coated parts with axial and radial leads. However, the basic capacitor element is similar for all styles. It is called a chip and consists of formulated dielectric materials which have been cast into thin layers, interspersed with metal electrodes alternately exposed on opposite
edges of the laminated structure. The entire structure is fired at high temperature to produce a monolithic block which provides high capacitance values in a small physical volume. After firing, conductive terminations are applied to opposite ends of the chip to make contact with the exposed electrodes. Termination materials and methods vary depending on the intended use.

TEMPERATURE CHARACTERISTICS

Ceramic dielectric materials can be formulated with a wide range of characteristics. The EIA standard for ceramic dielectric capacitors RS-198 divides ceramic dielectrics into the following classes:

Class III General purpose capacitors, suitable for by-pass coupling or other applications in which dielectric losses, high insulation resistance and stability of capacitance characteristics are of little or
no importance. Class III capacitors are similar to Class

Class I Temperature compensating capacitors, II capacitors except for temperature characteristics,
suitable for resonant circuit application or other appli- which are greater than ± Class III capacitors
cations where high Q and stability of capacitance char- have the highest volumetric efficiency and poorest
acteristics are required. Class I capacitors have stability of any type.
predictable temperature coefficients and are not
affected by voltage, frequency or time. They are made from materials which are not ferro-electric, yielding superior stability but low volumetric efficiency. Class I capacitors are the most stable type available, but have the lowest volumetric efficiency.

KEMET leaded ceramic capacitors are offered in the three most popular temperature characteristics:

C0G Class I, with a temperature coefficient of 0 ± 30 ppm per degree C over an operating temperature range of - 55°C to + 125°C Also
known as “NP0” .

Class II Stable capacitors, suitable for bypass

X7R Class II, with a maximum capacitance
or coupling applications or frequency discriminating
change of ± 15% over an operating temperature
circuits where Q and stability of capacitance char-
range of - 55°C to + 125°C.
acteristics are not of major importance. Class II

Z5U Class III, with a maximum capacitance
capacitors have temperature characteristics of ± 15%
change of + 22% - 56% over an operating tem-
or less. They are made from materials which are
perature range of + 10°C to + 85°C.
ferro-electric, yielding higher volumetric efficiency but
less stability. Class II capacitors are affected by Specified electrical limits for these three temperature
temperature, voltage, frequency and time.
characteristics are shown in Table

SPECIFIED ELECTRICAL LIMITS

Parameter

Dissipation Factor Measured at following conditions. C0G 1 kHz and 1 vrms if capacitance >1000pF 1 MHz and 1 vrms if capacitance 1000 pF X7R 1 kHz and 1 vrms* or if extended cap range vrms Z5U 1 kHz and vrms

Dielectric Stength times rated DC voltage.

Insulation Resistance IR At rated DC voltage, whichever of the two is smaller

Temperature Characteristics Range, °C Capacitance Change without DC voltage
* MHz and 1 vrms if capacitance 100 pF on military product.

Temperature Characteristics

Pass Subsequent IR Test
ORDERING INFORMATION

C 052 C 102 K 2 R 5 T A

CERAMIC

CASE SIZE See Table Below

SPECIFICATION C Standard

CAPACITANCE PICOFARAD CODE

Expressed in picofarads pF . First two digits represent significant figures. Third digit specifies number of zeros following except 9 indicates division by Examples µF = 100,000 pF = 104 and pF = See tables for standard values.

CAPACITANCE TOLERANCE

Standard

Others

M ±20%

H ±3%

K ±10%

G ±2%

J ±5%

F ±1%

D ±.5pF

Standard tolerances for each Series are shown in the repetitive parts lists.

FAILURE RATE A Not Applicable

LEAD MATERIAL C 60/40 Tin/Lead SnPb T 100% Tin Sn C052,

C062 only

INTERNAL CONSTRUCTION 5 Multilayer

TEMPERATURE CHARACTERISTIC

KEMET Designator

Cap. Change with Temp.

EIA Equivalent

Temp Range, °C

Measured without DC Bias Voltage

Ultra Stable NP0
-55 to +125°
±30 ppm/°C

R Stable
-55° to +125
±15%

WORKING VOLTAGE DC 2 200V 1 100V 5 50V

Case Sizes

Radial

Axial

C052

C114

C062

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived C062C394K5R5CA Datasheet file may be downloaded here without warranties.

Datasheet ID: C062C394K5R5CA 644732