ISL9518AHRTZ

ISL9518AHRTZ Datasheet

ISL9518, ISL9518A

Part	Datasheet
ISL9518AHRTZ	ISL9518AHRTZ (pdf)

Related Parts	Information
ISL9518AHRTZ-T	ISL9518AHRTZ-T
ISL9518HRTZ-T	ISL9518HRTZ-T
ISL9518HRTZ	ISL9518HRTZ

PDF Datasheet Preview
Data Sheet ISL9518, ISL9518A December 8, 2008 FN6775.0 Narrow VDC Regulator/Charger with SMBus Interface The ISL9518, ISL9518A are highly integrated Narrow VDC system voltage regulators and battery charger controllers. Operating parameters are programmable over the System Management Bus SMBus . The ISL9518, ISL9518A are designed for applications where the system power source is either the battery pack or the output of the regulator/charger. This makes the max voltage to the system equal to the max battery voltage instead of the max adapter voltage. The ISL9518, ISL9518A also include a system to control trickle charging deeply discharged batteries while maintaining system voltage at a user defined minimum. High efficiency is achieved with a DC/DC synchronous-rectifier buck converter, equipped with diode emulation for enhanced light load efficiency and AC-adapter boosting prevention. The ISL9518, ISL9518A can charge two to four series connected Lithium-ion cells, at up to 8A charge current. The ISL9518 has default settings for 2-cell systems and the ISL9518A has default settings for 3-cell systems. Integrated MOSFET drivers and bootstrap diode result in fewer components and smaller implementation area. Low offset current-sense amplifiers provide high accuracy. The ISL9518, ISL9518A provide two open drain digital outputs that indicate the presence of the AC adapter and trickle charge state. Trickle charge state and AC adapter present indicators are also available via SMBus. The ISL9518, ISL9518A also provide two analog outputs that indicate the adapter current and battery discharge current with 4% accuracy. Pinout ISL9518, ISL9518A 28 LD TQFN TOP VIEW CSIP CSIN AGND BOOT UGATE PHASE PGND 28 27 26 25 24 23 22 SGATE 1 21 LGATE DCIN 2 20 VDDP ADET 3 19 VDD VREF 4 18 CSOP ICOMP 5 17 CSON AGND 6 16 BGATE VCOMP 7 15 AGND 8 9 10 11 12 13 14 • System Voltage Accuracy -10°C to +100°C • ±3% Accurate Input Current Limit • ±3% Accurate Battery Charge Current Limit • Switching Frequency can be Reduced via SMBus for Higher Efficiency at Light Load Conditions • Trickle Charge System for Deeply Discharged Batteries - Automatic Trickle Charge Current 256mA - Holds Minimum Voltage to System • SMBus 2-Wire Serial Interface • Battery Short Circuit Protection • Fast System-Load Transient Response • Monitor Outputs - Adapter Current Accuracy - Trickle Charge Mode Indicator - AC-Adapter Present Indicator • 11-Bit Max System Voltage Setting • 7-Bit Min System Voltage Setting • 6-Bit Charge Current Setting • 6-Bit Adapter Current Setting • Over 8A Battery Charger Current • Over 8A Maximum Adapter Current • +8V to +22V Adapter Voltage Range • Pb-Free RoHS Compliant • Notebook Computers • Tablet PCs • Portable Equipment with Rechargeable Batteries VFB ACMON SDA SCL VSMB TRKLN ADPR CAUTION These devices are sensitive to electrostatic discharge follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 \| Intersil and design is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. All Rights Reserved All other trademarks mentioned are the property of their respective owners. ISL9518, ISL9518A Ordering Information PART NUMBER Note PART MARKING TEMP RANGE °C PACKAGE Pb-Free PKG. DWG. # ISL9518HRTZ* 951 8HRTZ -10 to +100 28 Ld 4x4 TQFN L28.4x4A ISL9518AHRTZ* 951 8AHRTZ -10 to +100 28 Ld 4x4 TQFN L28.4x4A *Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTE These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations . Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. VSMB SDA SCL ACMON CSIP CSIN ICOMP CSOP CSON VFB VCOMP TRKLN DCIN SMBus CHARGE CURRENT 6 CC DAC ADAPTER CURRENT 6 AC DAC MAXSYSTEMVOLTAGE 11 MAXSVDAC MINSYSTEMVOLTAGE 7 MINSVDAC LINEAR REGULATOR ISOLATE ADAPTER ISOLATE ADAPTER FSW LOW POWER AC_PR AC_PR TRICKLE ISL9518, ISL9518A VREF + - REFERENCE

PDF Datasheet Preview

Data Sheet

ISL9518, ISL9518A

December 8, 2008

FN6775.0

Narrow VDC Regulator/Charger with SMBus Interface

The ISL9518, ISL9518A are highly integrated Narrow VDC system voltage regulators and battery charger controllers. Operating parameters are programmable over the System Management Bus SMBus . The ISL9518, ISL9518A are designed for applications where the system power source is either the battery pack or the output of the regulator/charger. This makes the max voltage to the system equal to the max battery voltage instead of the max adapter voltage. The ISL9518, ISL9518A also include a system to control trickle charging deeply discharged batteries while maintaining system voltage at a user defined minimum. High efficiency is achieved with a DC/DC synchronous-rectifier buck converter, equipped with diode emulation for enhanced light load efficiency and AC-adapter boosting prevention. The ISL9518, ISL9518A can charge two to four series connected Lithium-ion cells, at up to 8A charge current. The ISL9518 has default settings for 2-cell systems and the ISL9518A has default settings for 3-cell systems. Integrated MOSFET drivers and bootstrap diode result in fewer components and smaller implementation area. Low offset current-sense amplifiers provide high accuracy.

The ISL9518, ISL9518A provide two open drain digital outputs that indicate the presence of the AC adapter and trickle charge state. Trickle charge state and AC adapter present indicators are also available via SMBus. The ISL9518, ISL9518A also provide two analog outputs that indicate the adapter current and battery discharge current with 4% accuracy.

Pinout

ISL9518, ISL9518A 28 LD TQFN TOP VIEW

CSIP CSIN AGND BOOT UGATE PHASE PGND
28 27 26 25 24 23 22

SGATE 1
21 LGATE

DCIN 2
20 VDDP

ADET 3
19 VDD

VREF 4
18 CSOP

ICOMP 5
17 CSON

AGND 6
16 BGATE

VCOMP 7
15 AGND
8 9 10 11 12 13 14
• System Voltage Accuracy -10°C to +100°C
• ±3% Accurate Input Current Limit
• ±3% Accurate Battery Charge Current Limit
• Switching Frequency can be Reduced via SMBus for

Higher Efficiency at Light Load Conditions
• Trickle Charge System for Deeply Discharged Batteries
- Automatic Trickle Charge Current 256mA - Holds Minimum Voltage to System
• SMBus 2-Wire Serial Interface
• Battery Short Circuit Protection
• Fast System-Load Transient Response
• Monitor Outputs - Adapter Current Accuracy - Trickle Charge Mode Indicator - AC-Adapter Present Indicator
• 11-Bit Max System Voltage Setting
• 7-Bit Min System Voltage Setting
• 6-Bit Charge Current Setting
• 6-Bit Adapter Current Setting
• Over 8A Battery Charger Current
• Over 8A Maximum Adapter Current
• +8V to +22V Adapter Voltage Range
• Pb-Free RoHS Compliant
• Notebook Computers
• Tablet PCs
• Portable Equipment with Rechargeable Batteries

VFB ACMON

SDA SCL VSMB TRKLN ADPR

CAUTION These devices are sensitive to electrostatic discharge follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil and design is a registered trademark of Intersil Americas Inc.

Copyright Intersil Americas Inc. All Rights Reserved

All other trademarks mentioned are the property of their respective owners.

ISL9518, ISL9518A
Ordering Information

PART NUMBER Note

PART MARKING

TEMP RANGE °C

PACKAGE Pb-Free

PKG. DWG. #

ISL9518HRTZ*
951 8HRTZ
-10 to +100
28 Ld 4x4 TQFN

L28.4x4A

ISL9518AHRTZ*
951 8AHRTZ
-10 to +100
28 Ld 4x4 TQFN

L28.4x4A
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications.

NOTE These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations . Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.

VSMB SDA SCL

ACMON CSIP CSIN

ICOMP CSOP CSON

VFB VCOMP

TRKLN

DCIN

SMBus

CHARGE CURRENT
6 CC DAC

ADAPTER CURRENT
6 AC DAC

MAXSYSTEMVOLTAGE 11 MAXSVDAC

MINSYSTEMVOLTAGE
7 MINSVDAC

LINEAR REGULATOR

ISOLATE ADAPTER

ISOLATE ADAPTER FSW

LOW POWER

AC_PR

AC_PR TRICKLE

ISL9518, ISL9518A

VREF + -

REFERENCE

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ISL9518AHRTZ Datasheet file may be downloaded here without warranties.

Datasheet ID: ISL9518AHRTZ 639204