IS49FL004T-33JCE

IS49FL004T-33JCE Datasheet

IS49FL004T

Part	Datasheet
IS49FL004T-33JCE	IS49FL004T-33JCE (pdf)

Related Parts	Information
IS49FL004T-33VCE	IS49FL004T-33VCE

PDF Datasheet Preview
2 Mbit / 4 Mbit Volt-only Firmware Hub/LPC Flash Memory IS49FL004T • Single Power Supply Operation - Low voltage range V - V • Standard Intel Firmware Hub/LPC Interface - Read compatible to 82802 Firmware Hub devices - Conforms to Intel LPC Interface Specification • Memory Configuration - IS49FL002 256K x 8 2 Mbit - IS49FL004 512K x 8 4 Mbit • Cost Effective Sector/Block Architecture - IS49FL002 Sixty-four uniform 4 Kbyte sectors, or sixteen uniform 16 Kbyte blocks sector group - IS49FL004 One hundred and twenty-eight uniform 4 Kbyte sectors, or eight uniform 64 Kbyte blocks sector group • Top Boot Block - IS49FL002 16 Kbyte top Boot Block - IS49FL004 64 Kbyte top Boot Block • Automatic Erase and Program Operation - Build-in automatic program verification for extended product endurance - Typical 25 us/byte programming time - Typical 50 ms sector/block/chip erase time • Two Configurable Interfaces - In-System hardware interface Auto detection of Firmware Hub FWH or Low Pin Count LPC memory cycle for in-system read and write operations - Address/Address-Multiplexed A/A Mux interface for programming on EPROM Programmers during manufacturing • Firmware HUB FWH /Low Pin Count LPC Mode - 33 MHz synchronous operation with PCI bus - 5-signal communication interface for in-system read and write operations - Standard SDP Command Set - Data# Polling and Toggle Bit features - Register-based read and write protection for each block FWH mode only - 4 ID pins for multiple Flash chips selection FWH mode only - 5 GPI pins for General Purpose Input Register - TBL# pin for hardware write protection to Boot Block - WP# pin for hardware write protection to whole memory array except Boot Block • Address/Address Multiplexed A/A Mux Mode - 11-pin multiplexed address and 8-pin data I/O interface - Supports fast programming on EPROM programmers - Standard SDP Command Set - Data# Polling and Toggle Bit features • Lower Power Consumption - Typical 2 mA active read current - Typical 7 mA program/erase current • High Product Endurance - Guarantee 100,000 program/erase cycles per single sector preliminary - Minimum 20 years data retention • Compatible Pin-out and Packaging - 32-pin 8 mm x 14 mm VSOP - 32-pin PLCC - Optional Halogen-free package • Hardware Data Protection IS49FL004T The IS49FL002/004 are 2 Mbit/4 Mbit Volt-only Flash Memories used as BIOS in PCs and Notebooks. These devices are designed to use a single low voltage, ranging from Volt to Volt, power supply to perform insystem or off-system read, erase and program operations. The Volt V power supply are not required for the The memory array of IS49FL002 is divided into uniform 4 Kbyte sectors, or uniform 16 Kbytes blocks sector group - consists of four adjecent sectors . The memory array of IS49FL004 is divided into uniform 4 Kbyte sectors, or uniform 64 Kbyte blocks sector group - consists of sixteen adjecent sectors . The sector or block erase feature allows users to flexibly erase a memory area as small as 4 Kbyte or as large as 64 Kbyte by one single erase operation without affecting the data in others. The chip erase feature allows the whole memory to be erased in one single erase operation. The devices can be programmed on a byte-by-byte basis after performing the erase operation. The program operation of IS49FL002/004 is executed by issuing the program command code into command register. The internal control logic automatically handles the programming voltage ramp-up and timing. The erase operation of the devices is executed by issuing the sector, block, or chip erase command code into command register. The internal control logic automatically handles the erase voltage ramp-up and timing. The preprogramming on the array which has not been programmed is not required before an erase operation. The devices offer Data# Polling and Toggle Bit functions in FWH/LPC and A/A Mux modes, the progress or completion of program and erase operations can be detected by reading the Data# Polling on I/O7 or Toggle Bit on I/O6. PRODUCT ORDERING INFORMATION IS49FL00x T -33 J C E IS49FL004T Environmental Attribute E = Halogen-free Package Blank = Standard Package Temperature Range C = Commercial 0°C to +85°C Package Type J = 32-pin Plastic J-Leaded Chip Carrier 32J V = 32-pin 8 mm x 14 mm VSOP 32V Speed Option Boot Block Location T = Top Boot Block Device Number IS49FL002 2 Mbit IS49FL004 4 Mbit IS49FL002T-33JCE IS49FL002T-33JC IS49FL002T-33VCE IS49FL002T-33VC IS49FL004T-33JCE IS49FL004T-33JC IS49FL004T-33VCE IS49FL004T-33VC MHz 33 Boot Block Location Package Temperature Range 32J Commercial 0oC to + 85oC 32V 32J Commercial 0oC to +85oC 32V IS49FL004T PIN DESCRIPTIONS S YM B O L A [1 0 :0 ] R/C # I/O [7 :0 ] WE# OE # IC RS T# IN IT # G P I[4 :0 ] TB L # WP # F W H[3 :0 ] FW H4 L A D [3 :0 ] LF RA M E # CL K ID [3 :0 ] GN D NC TYPE I I/O I I/O I/O I In te rfac e PP FW H LPC D E S C R IP T IO N A d re s Inp uts F o r inp uting the m ultip le x a d re s e s a nd c o m a nd s in P m o d e R o w a nd c o lum n a d re s e s a re la tc he d uring a re a d o r w rite c yc le c o ntro lle d b y R /C # p in. R o w /C o lum n S e le c t To ind ic a te the ro w o r c o lum n a d re s in P m o d e W he n this p in g o e s lo w, the ro w a d re s is la tc he d W he n this p in g o e s hig h, the c o lum n a d re s is la tc he d D a ta Inp uts /O utp uts U s e d fo r A /A M ux m o d e o nly, to inp ut co m a nd /d a ta d uring write o p e ra tio n a nd to o utp ut d a ta d uring re a d o p e ra tio n. The d a ta p ins flo a t to tri-s ta te whe n O E # is d is a b le d W rite E na b le A c tiva te the d e vic e fo r w rite o p e ra tio n. W E # is a c tive lo w. O utp ut E na b le C o ntro l the d e vic e 's o utp ut b uffe rs d uring a re a d c yc le O E # is a c tive lo w. Inte rfa c e C o nfig ura tio n S e le c t This p in d e te rm ine s w hic h m o d e is s e le c te d W he n p ulls hi g h, the d e vic e nte rs into A /A M ux m o d e W he n X p ulls lo w, F W H /L P C m o d e is s e le c te d This p in m us t b e s e tup d uring ORDERING INFORMATION: Density 512K Frequency Order Part Number IS49FLO00T 100 IS49FLO00T Package 32-pin PLCC 32-pin PLCC A* = A1, A2, A3, Automotive Temperature Ranges IS49FL004T

PDF Datasheet Preview

2 Mbit / 4 Mbit Volt-only Firmware Hub/LPC Flash Memory

IS49FL004T
• Single Power Supply Operation - Low voltage range V - V
• Standard Intel Firmware Hub/LPC Interface - Read compatible to 82802 Firmware Hub
devices - Conforms to Intel LPC Interface Specification
• Memory Configuration - IS49FL002 256K x 8 2 Mbit - IS49FL004 512K x 8 4 Mbit
• Cost Effective Sector/Block Architecture
- IS49FL002 Sixty-four uniform 4 Kbyte sectors, or sixteen uniform 16 Kbyte blocks sector group
- IS49FL004 One hundred and twenty-eight uniform 4 Kbyte sectors, or eight uniform 64 Kbyte blocks sector group
• Top Boot Block
- IS49FL002 16 Kbyte top Boot Block - IS49FL004 64 Kbyte top Boot Block
• Automatic Erase and Program Operation
- Build-in automatic program verification for extended product endurance
- Typical 25 us/byte programming time - Typical 50 ms sector/block/chip erase time
• Two Configurable Interfaces
- In-System hardware interface Auto detection of Firmware Hub FWH or Low Pin Count LPC memory cycle for in-system read and write operations
- Address/Address-Multiplexed A/A Mux interface for programming on EPROM Programmers during manufacturing
• Firmware HUB FWH /Low Pin Count LPC

Mode - 33 MHz synchronous operation with PCI bus - 5-signal communication interface for in-system
read and write operations - Standard SDP Command Set - Data# Polling and Toggle Bit features - Register-based read and write protection for
each block FWH mode only - 4 ID pins for multiple Flash chips selection

FWH mode only - 5 GPI pins for General Purpose Input Register - TBL# pin for hardware write protection to Boot

Block - WP# pin for hardware write protection to whole
memory array except Boot Block
• Address/Address Multiplexed A/A Mux

Mode - 11-pin multiplexed address and 8-pin data I/O
interface - Supports fast programming on EPROM programmers
- Standard SDP Command Set
- Data# Polling and Toggle Bit features
• Lower Power Consumption
- Typical 2 mA active read current - Typical 7 mA program/erase current
• High Product Endurance
- Guarantee 100,000 program/erase cycles per single sector preliminary
- Minimum 20 years data retention
• Compatible Pin-out and Packaging
- 32-pin 8 mm x 14 mm VSOP - 32-pin PLCC - Optional Halogen-free package
• Hardware Data Protection

IS49FL004T

The IS49FL002/004 are 2 Mbit/4 Mbit Volt-only Flash Memories used as BIOS in PCs and Notebooks. These devices are designed to use a single low voltage, ranging from Volt to Volt, power supply to perform insystem or off-system read, erase and program operations. The Volt V power supply are not required for the

The memory array of IS49FL002 is divided into uniform 4 Kbyte sectors, or uniform 16 Kbytes blocks sector group - consists of four adjecent sectors . The memory array of IS49FL004 is divided into uniform 4 Kbyte sectors, or uniform 64 Kbyte blocks sector group - consists of sixteen adjecent sectors . The sector or block erase feature allows users to flexibly erase a memory area as small as 4 Kbyte or as large as 64 Kbyte by one single erase operation without affecting the data in others. The chip erase feature allows the whole memory to be erased in one single erase operation. The devices can be programmed on a byte-by-byte basis after performing the erase operation.

The program operation of IS49FL002/004 is executed by issuing the program command code into command register. The internal control logic automatically handles the programming voltage ramp-up and timing. The erase operation of the devices is executed by issuing the sector, block, or chip erase command code into command register. The internal control logic automatically handles the erase voltage ramp-up and timing. The preprogramming on the array which has not been programmed is not required before an erase operation. The devices offer Data# Polling and Toggle Bit functions in FWH/LPC and A/A Mux modes, the progress or completion of program and erase operations can be detected by reading the Data# Polling on I/O7 or Toggle Bit on I/O6.
PRODUCT ORDERING INFORMATION

IS49FL00x T -33 J C E

IS49FL004T

Environmental Attribute E = Halogen-free Package Blank = Standard Package Temperature Range C = Commercial 0°C to +85°C Package Type J = 32-pin Plastic J-Leaded Chip Carrier 32J V = 32-pin 8 mm x 14 mm VSOP 32V

Speed Option Boot Block Location T = Top Boot Block

Device Number IS49FL002 2 Mbit IS49FL004 4 Mbit

IS49FL002T-33JCE IS49FL002T-33JC IS49FL002T-33VCE IS49FL002T-33VC IS49FL004T-33JCE IS49FL004T-33JC IS49FL004T-33VCE IS49FL004T-33VC

MHz 33

Boot Block Location

Package Temperature Range
32J Commercial
0oC to + 85oC 32V
32J Commercial
0oC to +85oC 32V

IS49FL004T

PIN DESCRIPTIONS

S YM B O L A [1 0 :0 ] R/C # I/O [7 :0 ] WE# OE #

IC RS T# IN IT #

G P I[4 :0 ]

TB L # WP # F W H[3 :0 ] FW H4 L A D [3 :0 ] LF RA M E # CL K

ID [3 :0 ]

GN D NC

TYPE I

I/O I

I/O I/O I

In te rfac e PP FW H LPC

D E S C R IP T IO N

A d re s Inp uts F o r inp uting the m ultip le x a d re s e s a nd c o m a nd s in

P m o d e R o w a nd c o lum n a d re s e s a re la tc he d uring a re a d o r
w rite c yc le c o ntro lle d b y R /C # p in.

R o w /C o lum n S e le c t To ind ic a te the ro w o r c o lum n a d re s in P
m o d e W he n this p in g o e s lo w, the ro w a d re s is la tc he d W he n this
p in g o e s hig h, the c o lum n a d re s is la tc he d

D a ta Inp uts /O utp uts U s e d fo r A /A M ux m o d e o nly, to inp ut
co m a nd /d a ta d uring write o p e ra tio n a nd to o utp ut d a ta d uring re a d
o p e ra tio n. The d a ta p ins flo a t to tri-s ta te whe n O E # is d is a b le d

W rite E na b le A c tiva te the d e vic e fo r w rite o p e ra tio n. W E # is a c tive lo w.

O utp ut E na b le C o ntro l the d e vic e 's o utp ut b uffe rs d uring a re a d c yc le O E # is a c tive lo w.

Inte rfa c e C o nfig ura tio n S e le c t This p in d e te rm ine s w hic h m o d e is
s e le c te d W he n p ulls hi g h, the d e vic e nte rs into A /A M ux m o d e W he n

X p ulls lo w, F W H /L P C m o d e is s e le c te d This p in m us t b e s e tup d uring
ORDERING INFORMATION:

Density 512K

Frequency

Order Part Number

IS49FLO00T 100

IS49FLO00T

Package 32-pin PLCC 32-pin PLCC

A* = A1, A2, A3, Automotive Temperature Ranges

IS49FL004T

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived IS49FL004T-33JCE Datasheet file may be downloaded here without warranties.

Datasheet ID: IS49FL004T-33JCE 639285