M2040-01-533.3334T

M2040-01-533.3334T Datasheet

M2040

Part	Datasheet
M2040-01-533.3334T	M2040-01-533.3334T (pdf)

Related Parts	Information
M2040-01-533.3334	M2040-01-533.3334

PDF Datasheet Preview
Integrated Circuit Systems, Inc. M2040 FREQUENCY TRANSLATION PLL WITH AUTOSWITCH The M2040 is a VCSO Voltage Controlled SAW Oscillator based clock generator PLL designed for clock protection, frequency translation and jitter attenuation in fault tolerant computing applications. It features dual differential inputs with two modes of input selection manual and automatic upon clock failure. The clock multiplication ratios and output divider ratio are pin selectable. External loop components allow the tailoring of PLL loop response. Integrated SAW surface acoustic wave delay line VCSO frequency of or MHz;* outputs VCSO frequency or half pin-configurable dividers Loss of Lock LOL indicator output Narrow Bandwidth control input NBW Pin Initialization INIT input overrides NBW at power-up Dual reference clock inputs support LVDS, LVPECL, LVCMOS, LVTTL Automatic non-revertive reference clock reselection upon clock failure controlled PLL slew rate ensures normal system operation during reference reselection Acknowledge pin indicates the actively selected reference input Dual differential LVPECL outputs Low phase jitter of < 0.5ps rms, typical 12kHz to 20MHz or 50kHz to 80MHz Industrial temperature available Single 3.3V power supply Small 9 x 9 mm SMT surface mount package SIMPLIFIED BLOCK DIAGRAM PIN ASSIGNMENT 9 x 9 mm SMT nDIF_REF1 DIF_REF1 REF_SEL nDIF_REF0 DIF_REF0 AUTO FIN_SEL1 FIN_SEL0 MR_SEL REF_ACK LOL NBW VCC DNC M2040 Top View P_SEL INIT nFOUT0 FOUT0 GND nFOUT1 FOUT1 VCC GND nOP_IN OP_OUT nOP_OUT OP_IN Figure 1 Pin Assignment Example Input / Output Frequency Combinations Input MHz VCSO * MHz Output MHz Table 1 Example Input / Output Frequency Combinations * Specify VCSO center frequency at time of order. Loop Filter M2040 ORDERING INFORMATION Part Number: M2040- 01 - xxx.xxxx Temperature “- ” = 0 to +70 oC commercial I = - 40 to +85 oC industrial Frequency MHz Consult ICS for available VCSO frequencies Figure 10 Ordering Information Example Part Numbers VCSO Freq Temperature commercial industrial M2040-01- M2040-01I commercial industrial M2040-01- M2040-01I Table 12 Example Part Numbers Consult ICS for the availability of other VCSO frequencies. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems ICS assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. M2040 Datasheet Rev 12 of 12 Integrated Circuit Systems, Inc. ● Networking & Communications ● ● tel 508 852-5400

PDF Datasheet Preview

Integrated Circuit Systems, Inc.

M2040

FREQUENCY TRANSLATION PLL WITH AUTOSWITCH

The M2040 is a VCSO Voltage Controlled SAW Oscillator based clock generator PLL designed for clock protection, frequency translation and jitter attenuation in fault tolerant computing applications. It features dual differential inputs with two modes of input selection manual
and automatic upon clock failure. The clock multiplication ratios and output divider ratio are pin selectable. External loop components allow the tailoring of PLL loop response.

Integrated SAW surface acoustic wave delay line VCSO frequency of or MHz;* outputs VCSO frequency or half pin-configurable dividers

Loss of Lock LOL indicator output

Narrow Bandwidth control input NBW Pin Initialization INIT input overrides NBW at power-up

Dual reference clock inputs support LVDS, LVPECL, LVCMOS, LVTTL

Automatic non-revertive reference clock reselection upon clock failure controlled PLL slew rate ensures normal system operation during reference reselection

Acknowledge pin indicates the actively selected reference input

Dual differential LVPECL outputs

Low phase jitter of < 0.5ps rms, typical 12kHz to 20MHz or 50kHz to 80MHz

Industrial temperature available

Single 3.3V power supply

Small 9 x 9 mm SMT surface mount package

SIMPLIFIED BLOCK DIAGRAM

PIN ASSIGNMENT 9 x 9 mm SMT
nDIF_REF1

DIF_REF1

REF_SEL
nDIF_REF0

DIF_REF0

AUTO

FIN_SEL1

FIN_SEL0 MR_SEL

REF_ACK LOL NBW VCC DNC

M2040

Top View

P_SEL INIT nFOUT0 FOUT0 GND nFOUT1 FOUT1 VCC GND
nOP_IN

OP_OUT
nOP_OUT

OP_IN

Figure 1 Pin Assignment

Example Input / Output Frequency Combinations

Input MHz VCSO * MHz Output MHz

Table 1 Example Input / Output Frequency Combinations
* Specify VCSO center frequency at time of order.

Loop Filter

M2040
ORDERING INFORMATION

Part Number:

M2040- 01 - xxx.xxxx

Temperature “- ” = 0 to +70 oC commercial I = - 40 to +85 oC industrial

Frequency MHz Consult ICS for available VCSO frequencies
Figure 10 Ordering Information Example Part Numbers

VCSO Freq

Temperature
commercial industrial

M2040-01- M2040-01I
commercial industrial

M2040-01- M2040-01I

Table 12 Example Part Numbers

Consult ICS for the availability of other VCSO frequencies.

While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems ICS assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments.

M2040 Datasheet Rev
12 of 12

Integrated Circuit Systems, Inc. ● Networking & Communications ● ● tel 508 852-5400

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived M2040-01-533.3334T Datasheet file may be downloaded here without warranties.

Datasheet ID: M2040-01-533.3334T 637419