5P49EE605NLGI

5P49EE605NLGI Datasheet

IDT5P49EE605

Part	Datasheet
5P49EE605NLGI	5P49EE605NLGI (pdf)

Related Parts	Information
5P49EE605NLGI8	5P49EE605NLGI8

PDF Datasheet Preview
LOW POWER CLOCK GENERATOR DATASHEET IDT5P49EE605 The IDT5P49EE605 is a programmable clock generator intended for low power, battery operated consumer applications. There are four internal PLLs, each individually programmable, allowing for four unique non-integer-related frequencies. The frequencies are generated from a single reference clock. The reference clock can come from either a TCXO or input clock. An additional 32.768kHz crystal oscillator is available to provide a real time clock or non-critical performance MHz processor clock. Two buffered reference Sine wave output clocks are supported with amplitude of 750 mV to 1V, peak to peak. The IDT5P49EE605 can be programmed through the use of the I2C interfaces. The programming interface enables the device to be programmed when it is in normal operation or what is commonly known as in system programmable. An internal EEPROM allows the user to save and restore the configuration of the device without having to reprogram it on power-up. Each of the four PLLs has an 8-bit reference divider and a 11-bit feedback divider. This allows the user to generate four unique non-integer-related frequencies. The PLL loop bandwidth is programmable to allow the user to tailor the PLL response to the application. For instance, the user can tune the PLL parameters to minimize jitter generation or to maximize jitter attenuation. Spread spectrum generation is supported on one of the PLLs. The device is specifically designed to work with display applications to ensure that the spread profile remains consistent for each HSYNC in order to reduce ROW noise. There are total six 8-bit output dividers. The outputs are connected to the PLLs via the switch matrix. The switch matrix allows the user to route the PLL outputs to any output bank. This feature can be used to simplify and optimize the board layout. In addition, each output's slew rate and enable/disable function can be programmed. Target Applications • Smart Mobile Handset • Personal Navigation Device PND • Camcorder • DSC • Portable Game Console • Personal Media Player • Four internal PLLs • Internal non-volatile EEPROM • Internal I2C EEPROM master interface • FAST 400kHz mode I2C serial interfaces • Input Frequencies TCXO 10 MHz to 40 MHz RTC Crystal kHz • Two buffered Sine wave outputs at 750 mV to 1Vpp • Output Frequency Ranges kHz to 120 MHz • Each PLL has an 8-bit reference divider and a 11-bit feedback-divider • 8-bit output-divider blocks • One of the PLLs support Spread Spectrum generation capable of configuration to pixel rate, with adjustable modulation rate and amplitude to support video clock with no visible artifacts • I/O Standards: Outputs - 1.8V/2.5V/3.3 V LVTTL/ LVCMOS • 3 independent adjustable VDDO groups. • Programmable Slew Rate Control • Programmable Loop Bandwidth Settings • Programmable output inversion to reduce bimodal jitter • Individual output enable/disable • Power-down/Sleep mode 10uA max in power down mode 32kHz clock output active sleep mode 100uA max in sleep mode • 1.8V VDD Core Voltage • Available in 24pin 4x4mm QFN packages • -40 to +85 C Industrial Temp operation LOW POWER CLOCK GENERATOR IDT5P49EE605 LOW POWER CLOCK GENERATOR Functional Block Diagram EEPROM CLOCK GENERATOR TCXO_IN TCXO _IN 750 mVpp to Vpp SDA SCL SEL[1:0] VDDA VDDO1 REFSELA PLLA Control Logic REFSELB PLLB SS REFSELC PLLC REFSELD PLLD VDDO2 VDDO3 Ordering Information Part / Order Number 5P49EE605NLGI 5P49EE605NLGI8 Marking see page 22 Shipping Packaging Tubes Tape and Reel Package 24pin VFQFPN 24pin VFQFPN Temperature -40 to +85° C -40 to +85° C “G” after the two-letter package code are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. LOW POWER CLOCK GENERATOR IDT5P49EE605 LOW POWER CLOCK GENERATOR EEPROM CLOCK GENERATOR Originator R.Willner R.Willner R. Willner R. Willner R. Willner R. Willner A.T. R. Willner Date Description of Change 6/02/10 Preliminary Datasheet release. 9/08/10 Updated thermal pad and dimensions on package drawing. Power ramp sequence. 10/29/10 Typographical changes. Loop filter calculations. Default register bit corrections. 01/19/11 Corrected notes on top-side marking. 04/13/11 Updated SCLK and SDA pin descriptions Updated DC Electrical Char table for 1.8V LVTTL added VIH and VIL. Updated “Lock Time/PLL Lock Time from shutdown mode” Typ. and Max. specs in AC Timing Electrical Char table. 05/04/11 Added Landing Pattern diagram. 09/30/11 Updated Power-up/Power-down Sequence notes. 10/17/11 Added VDDOx specs to Recommended Operations table Updated Power-up/down Sequence diagrams LOW POWER CLOCK GENERATOR IDT5P49EE605 LOW POWER CLOCK GENERATOR EEPROM CLOCK GENERATOR Innovate with IDT and accelerate your future networks. Contact: For Sales 800-345-7015 408-284-8200 Fax 408-284-2775 For Tech Support Corporate Headquarters Integrated Device Technology, Inc. 2011 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

PDF Datasheet Preview

LOW POWER CLOCK GENERATOR

DATASHEET

IDT5P49EE605

The IDT5P49EE605 is a programmable clock generator intended for low power, battery operated consumer applications. There are four internal PLLs, each individually programmable, allowing for four unique non-integer-related frequencies. The frequencies are generated from a single reference clock. The reference clock can come from either a TCXO or input clock. An additional 32.768kHz crystal oscillator is available to provide a real time clock or non-critical performance MHz processor clock.

Two buffered reference Sine wave output clocks are supported with amplitude of 750 mV to 1V, peak to peak.

The IDT5P49EE605 can be programmed through the use of the I2C interfaces. The programming interface enables the device to be programmed when it is in normal operation or what is commonly known as in system programmable. An internal EEPROM allows the user to save and restore the configuration of the device without having to reprogram it on power-up.

Each of the four PLLs has an 8-bit reference divider and a 11-bit feedback divider. This allows the user to generate four unique non-integer-related frequencies. The PLL loop bandwidth is programmable to allow the user to tailor the PLL response to the application. For instance, the user can tune the PLL parameters to minimize jitter generation or to maximize jitter attenuation.

Spread spectrum generation is supported on one of the PLLs. The device is specifically designed to work with display applications to ensure that the spread profile remains consistent for each HSYNC in order to reduce ROW noise.

There are total six 8-bit output dividers. The outputs are connected to the PLLs via the switch matrix. The switch matrix allows the user to route the PLL outputs to any output bank. This feature can be used to simplify and optimize the board layout. In addition, each output's slew rate and enable/disable function can be programmed.

Target Applications
• Smart Mobile Handset
• Personal Navigation Device PND
• Camcorder
• DSC
• Portable Game Console
• Personal Media Player
• Four internal PLLs
• Internal non-volatile EEPROM
• Internal I2C EEPROM master interface
• FAST 400kHz mode I2C serial interfaces
• Input Frequencies

TCXO 10 MHz to 40 MHz RTC Crystal kHz
• Two buffered Sine wave outputs at 750 mV to 1Vpp
• Output Frequency Ranges kHz to 120 MHz
• Each PLL has an 8-bit reference divider and a 11-bit
feedback-divider
• 8-bit output-divider blocks
• One of the PLLs support Spread Spectrum generation
capable of configuration to pixel rate, with adjustable modulation rate and amplitude to support video clock with no visible artifacts
• I/O Standards:

Outputs - 1.8V/2.5V/3.3 V LVTTL/ LVCMOS
• 3 independent adjustable VDDO groups.
• Programmable Slew Rate Control
• Programmable Loop Bandwidth Settings
• Programmable output inversion to reduce bimodal jitter
• Individual output enable/disable
• Power-down/Sleep mode
10uA max in power down mode 32kHz clock output active sleep mode 100uA max in sleep mode
• 1.8V VDD Core Voltage
• Available in 24pin 4x4mm QFN packages
• -40 to +85 C Industrial Temp operation

LOW POWER CLOCK GENERATOR

IDT5P49EE605 LOW POWER CLOCK GENERATOR

Functional Block Diagram

EEPROM CLOCK GENERATOR

TCXO_IN

TCXO _IN 750 mVpp to Vpp

SDA SCL SEL[1:0]

VDDA

VDDO1

REFSELA

PLLA

Control Logic

REFSELB PLLB SS

REFSELC

PLLC

REFSELD PLLD

VDDO2

VDDO3
Ordering Information

Part / Order Number
5P49EE605NLGI 5P49EE605NLGI8

Marking
see page 22

Shipping Packaging

Tubes Tape and Reel

Package
24pin VFQFPN 24pin VFQFPN

Temperature
-40 to +85° C -40 to +85° C
“G” after the two-letter package code are the Pb-Free configuration and are RoHS compliant.

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.

LOW POWER CLOCK GENERATOR

IDT5P49EE605 LOW POWER CLOCK GENERATOR

EEPROM CLOCK GENERATOR

Originator R.Willner R.Willner R. Willner R. Willner R. Willner

R. Willner A.T.

R. Willner

Date Description of Change
6/02/10 Preliminary Datasheet release.
9/08/10 Updated thermal pad and dimensions on package drawing. Power ramp sequence.
10/29/10 Typographical changes. Loop filter calculations. Default register bit corrections.
01/19/11 Corrected notes on top-side marking.
04/13/11

Updated SCLK and SDA pin descriptions Updated DC Electrical Char table for 1.8V LVTTL added VIH and VIL. Updated “Lock Time/PLL Lock Time from shutdown mode” Typ. and Max. specs in AC Timing Electrical Char table.
05/04/11 Added Landing Pattern diagram.
09/30/11 Updated Power-up/Power-down Sequence notes.
10/17/11 Added VDDOx specs to Recommended Operations table Updated Power-up/down Sequence diagrams

LOW POWER CLOCK GENERATOR

IDT5P49EE605 LOW POWER CLOCK GENERATOR

EEPROM CLOCK GENERATOR

Innovate with IDT and accelerate your future networks. Contact:

For Sales
800-345-7015 408-284-8200 Fax 408-284-2775

For Tech Support

Corporate Headquarters

Integrated Device Technology, Inc.
2011 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 5P49EE605NLGI Datasheet file may be downloaded here without warranties.

Datasheet ID: 5P49EE605NLGI 637269