810N252CKI-02LF

810N252CKI-02LF Datasheet

ICS810N252I-02

Part	Datasheet
810N252CKI-02LF	810N252CKI-02LF (pdf)

Related Parts	Information
810N252CKI-02LFT	810N252CKI-02LFT

PDF Datasheet Preview
Jitter Attenuator & FemtoClock Multiplier ICS810N252I-02 DATA SHEET The ICS810N252I-02 device uses IDT's fourth generation NG technology for optimal high clock frequency and low phase noise performance, combined with a low power consumption and high power supply noise rejection. The ICS810N252I-02 is a PLL based synchronous multiplier that is optimized for PDH or SONET to Ethernet clock jitter attenuation and frequency translation. The ICS810N252I-02 contains two internal frequency multiplication stages that are cascaded in series. The first stage is a jitter attenuator, capable of jitter attenuation down to 10Hz using the external loop filter. The second stage is a FemtoClock frequency multiplier that provides the low jitter, high frequency Ethernet output clock that easily meets Gigabit and 10 Gigabit Ethernet jitter requirements. Pre-divider and output divider multiplication ratios are selected using device selection control pins. The multiplication ratios are optimized to support most common clock rates used in PDH, SONET and Ethernet applications. The device requires the use of an external, inexpensive fundamental mode 27MHz crystal. The device is packaged in a space-saving 32-VFQFN package and supports industrial temperature range. Pin Assignment • Fourth generation NG technology • Two single-ended LVCMOS/LVTTL outputs • Each output supports independent frequency selection at 25MHz, 125MHz, 156.25MHz and 312.5MHz • Two differential inputs support the following input types LVPECL, LVDS, LVHSTL, HCSL • Accepts input frequencies from 8kHz to 155.52MHz including 8kHz, 1.544MHz, 2.048MHz, 19.44MHz, 25MHz, 77.76MHz, 125MHz and 155.52MHz • Crystal interface designed for a 27MHz crystal • Attenuates the phase jitter of the input clock by using a low-cost fundamental mode crystal • Customized settings for jitter attenuation and reference tracking using an external loop filter connection • FemtoClock NG frequency multiplier provides low jitter, high frequency output • Absolute pull range ±50ppm • Power supply noise ratio PSNR -85dB • FemtoClock NG VCO frequency 625MHz • RMS phase jitter 125MHz, using a 27MHz crystal 12kHz 20MHz 0.67ps typical • 3.3V supply voltage • -40°C to 85°C ambient operating temperature • Available in lead-free RoHS 6 package VDDX XTAL_IN XTAL_OUT CLK0 nCLK0 VDD CLK1 nCLK1 32 31 30 29 28 27 26 25 LF1 1 24 GND LF0 2 23 nc ISET 3 22 QB GND 4 21 VDDO CLK_SEL 5 20 nc VDD 6 19 QA RESERVED 7 18 GND GND 8 17 ODASEL_0 9 10 11 12 13 14 15 16 PDSEL_2 PDSEL_1 PDSEL_0 Ordering Information Table Ordering Information Part/Order Number Marking 810N252CKI-02LF ICS252CI02L 810N252CKI-02LFT ICS252CI02L JITTER ATTENUATOR & FEMTOCLOCK MULTIPLIER Package “Lead-Free” 32 Lead VFQFN “Lead-Free” 32 Lead VFQFN Shipping Packaging Tray Tape & Reel Temperature -40°C to 85°C -40°C to 85°C 2013 Integrated Device Technology, Inc. ICS810N252I-02 Data Sheet JITTER ATTENUATOR & FEMTOCLOCK MULTIPLIER We’ve Got Your Timing Solution 6024 Silver Creek Valley Road San Jose, California 95138 Sales 800-345-7015 inside USA +408-284-8200 outside USA Fax 408-284-2775 Technical Support +480-763-2056 DISCLAIMER Integrated Device Technology, Inc. IDT and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright All rights reserved.

PDF Datasheet Preview

Jitter Attenuator & FemtoClock Multiplier

ICS810N252I-02

DATA SHEET

The ICS810N252I-02 device uses IDT's fourth generation NG technology for optimal high clock frequency and low phase noise performance, combined with a low power consumption and high power supply noise rejection. The ICS810N252I-02 is a PLL based synchronous multiplier that is optimized for PDH or SONET to Ethernet clock jitter attenuation and frequency translation.

The ICS810N252I-02 contains two internal frequency multiplication stages that are cascaded in series. The first stage is a jitter attenuator, capable of jitter attenuation down to 10Hz using the external loop filter. The second stage is a FemtoClock frequency multiplier that provides the low jitter, high frequency Ethernet output clock that easily meets Gigabit and 10 Gigabit Ethernet jitter requirements. Pre-divider and output divider multiplication ratios are selected using device selection control pins. The multiplication ratios are optimized to support most common clock rates used in PDH, SONET and Ethernet applications. The device requires the use of an external, inexpensive fundamental mode 27MHz crystal. The device is packaged in a space-saving 32-VFQFN package and supports industrial temperature range.

Pin Assignment
• Fourth generation NG technology
• Two single-ended LVCMOS/LVTTL outputs
• Each output supports independent frequency selection at 25MHz,
125MHz, 156.25MHz and 312.5MHz
• Two differential inputs support the following input types LVPECL,

LVDS, LVHSTL, HCSL
• Accepts input frequencies from 8kHz to 155.52MHz including
8kHz, 1.544MHz, 2.048MHz, 19.44MHz, 25MHz, 77.76MHz, 125MHz and 155.52MHz
• Crystal interface designed for a 27MHz crystal
• Attenuates the phase jitter of the input clock by using a low-cost
fundamental mode crystal
• Customized settings for jitter attenuation and reference tracking
using an external loop filter connection
• FemtoClock NG frequency multiplier provides low jitter, high
frequency output
• Absolute pull range ±50ppm
• Power supply noise ratio PSNR -85dB
• FemtoClock NG VCO frequency 625MHz
• RMS phase jitter 125MHz, using a 27MHz crystal
12kHz 20MHz 0.67ps typical
• 3.3V supply voltage
• -40°C to 85°C ambient operating temperature
• Available in lead-free RoHS 6 package

VDDX XTAL_IN XTAL_OUT CLK0 nCLK0 VDD CLK1 nCLK1
32 31 30 29 28 27 26 25

LF1 1
24 GND

LF0 2
23 nc

ISET 3
22 QB

GND 4
21 VDDO

CLK_SEL 5
20 nc

VDD 6
19 QA

RESERVED 7
18 GND

GND 8
17 ODASEL_0
9 10 11 12 13 14 15 16

PDSEL_2 PDSEL_1 PDSEL_0
Ordering Information
Table Ordering Information

Part/Order Number

Marking
810N252CKI-02LF

ICS252CI02L
810N252CKI-02LFT

ICS252CI02L

JITTER ATTENUATOR & FEMTOCLOCK MULTIPLIER

Package “Lead-Free” 32 Lead VFQFN “Lead-Free” 32 Lead VFQFN

Shipping Packaging Tray

Tape & Reel

Temperature -40°C to 85°C -40°C to 85°C
2013 Integrated Device Technology, Inc.

ICS810N252I-02 Data Sheet

JITTER ATTENUATOR & FEMTOCLOCK MULTIPLIER

We’ve Got Your Timing Solution
6024 Silver Creek Valley Road San Jose, California 95138

Sales
800-345-7015 inside USA +408-284-8200 outside USA Fax 408-284-2775

Technical Support
+480-763-2056

DISCLAIMER Integrated Device Technology, Inc. IDT and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.

IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.

Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners.

Copyright All rights reserved.

More datasheets: M85049/47SW16 | M85049/47SW20 | M85049/47SW8 | M85049/47W10 | M85049/47W16 | M85049/47W22 | M85049/47W8 | IRF3575DTRPBF | CA3102R20-29PZ | 810N252CKI-02LFT

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 810N252CKI-02LF Datasheet file may be downloaded here without warranties.

Datasheet ID: 810N252CKI-02LF 637071