ICS252PMT

ICS252PMT Datasheet

FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER ICS252

Part	Datasheet
ICS252PMT	ICS252PMT (pdf)

Related Parts	Information
ICS252PM	ICS252PM

PDF Datasheet Preview
DATASHEET FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER ICS252 The ICS252 is a low cost, dual-output, field programmable clock synthesizer. The ICS252 can generate two output frequencies from 314 kHz to 200 MHz using up to two independently configurable PLLs. The outputs may employ Spread Spectrum techniques to reduce system electro-magnetic interference EMI . Using IDT’s VersaClock software to configure the PLL and output, the ICS252 contains a One-Time Programmable OTP ROM to allow field programmability. Programming features include 2 selectable configuration registers. The device employs Phase-Locked Loop PLL techniques to run from a standard fundamental mode, inexpensive crystal, or clock. It can replace multiple crystals and oscillators, saving board space and cost. The device also has a power-down feature that tri-states the clock outputs and turns off the PLLs when the PDTS pin is taken low. The ICS252 is also available in factory programmed custom versions for high-volume applications. • 8-pin SOIC package • Two addressable registers • Input crystal frequency of 5 to 27 MHz • Clock input frequency of 3 to 150 MHz • Output clock frequencies up to 200 MHz • Configurable Spread Spectrum Modulation • Operating voltage of V • Replaces multiple crystals and oscillators • Controllable output drive levels • Advanced, low-power CMOS process • Available in RoHS 5 green or RoHS 6 green and lead free compliant package Block Diagram X1 Crystal OTP ROM with PLL Values Crystal Oscillator External capacitors are required. VDD PLL1 PLL2 Divide Logic and Output Enable Control PDTS CLK1 CLK2 IDT / ICS FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER 1 ICS252 ICS252 FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Pin Assignment X1/ICLK PDTS 7 GND 6 CLK2 5 CLK1 Output Clock Selection Table SEL CLK1 MHz CLK2 MHz User User Configurable User User Configurable Spread Percentage User Configurable User Configurable 8-pin 150 mil SOIC Pin Descriptions Pin Number Ordering Information Part / Order Number 252PM 252PMI 252PMLF 252PMILF 252M-XX 252MI-XX 252M-XXLF 252MI-XXLF 252M-XXT 252MI-XXT 252M-XXLFT 252MI-XXLFT Marking See Page 7 Above 252M-XX 252MIXX 252MXXL 252MIXXL 252M-XX 252MIXX 252MXXL 252MIXXL Shipping Packaging Tubes Tape and Reel Tape and Reel Tape and Reel Tape and Reel Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC Temperature 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C Parts that are ordered with a “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant. The 252M-XX, 252M-XXLF, 252MI-XX, and 252MI-XXLF are factory programmed versions of the 252PM, 252PMLF, 252PMI, and 252PMILF. A unique “-XX” suffix is assigned by the factory for each custom configuration, and a separate data sheet is kept on file. For more information on custom part numbers programmed at the factory, please contact your local IDT sales and marketing representative. While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT / ICS FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER 9 ICS252 ICS252 FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Originator R.Willner R.Willner R.Willner R.Willner R.Willner R.Willner Date Description of Change 04/08/05 Preliminary release. 01/16/06 Corrected Block Diagram. Released from Prelim to Final. 06/13/06 Added "-XX" part ordering information and specific note pertaining to custom configurations of device. 08/10/07 Removed “Inernal pull-up resistor” info from PDTS pin description and added extrenal pull-up resistor statement/information. 08/20/07 Changed S1 pin name to “SEL” removed references to PDTS pin changed pull-up resistor value from 190 to 120 kOhms. 03/16/09 Correct page 1 text to have 2 selectable configuration registers. IDT / ICS FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER 10 ICS252 ICS252 FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER EPROM CLOCK SYNTHESIZER Innovate with IDT and accelerate your future networks. Contact: For Sales 800-345-7015 408-284-8200 Fax 408-284-2775 For Tech Support Corporate Headquarters Integrated Device Technology, Inc. 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

PDF Datasheet Preview

DATASHEET

FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER ICS252

The ICS252 is a low cost, dual-output, field programmable clock synthesizer. The ICS252 can generate two output frequencies from 314 kHz to 200 MHz using up to two independently configurable PLLs. The outputs may employ Spread Spectrum techniques to reduce system electro-magnetic interference EMI . Using IDT’s VersaClock software to configure the PLL and output, the ICS252 contains a One-Time Programmable OTP ROM to allow field programmability. Programming features include 2 selectable configuration registers.

The device employs Phase-Locked Loop PLL techniques to run from a standard fundamental mode, inexpensive crystal, or clock. It can replace multiple crystals and oscillators, saving board space and cost.

The device also has a power-down feature that tri-states the clock outputs and turns off the PLLs when the PDTS pin is taken low.

The ICS252 is also available in factory programmed custom versions for high-volume applications.
• 8-pin SOIC package
• Two addressable registers
• Input crystal frequency of 5 to 27 MHz
• Clock input frequency of 3 to 150 MHz
• Output clock frequencies up to 200 MHz
• Configurable Spread Spectrum Modulation
• Operating voltage of V
• Replaces multiple crystals and oscillators
• Controllable output drive levels
• Advanced, low-power CMOS process
• Available in RoHS 5 green or RoHS 6 green and lead
free compliant package

Block Diagram

X1 Crystal

OTP ROM with PLL Values

Crystal Oscillator

External capacitors are required.

VDD PLL1 PLL2

Divide Logic and Output Enable Control

PDTS

CLK1 CLK2

IDT / ICS FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER 1

ICS252

ICS252 FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER

EPROM CLOCK SYNTHESIZER

Pin Assignment

X1/ICLK

PDTS
7 GND
6 CLK2
5 CLK1

Output Clock Selection Table

SEL CLK1 MHz CLK2 MHz

User

User

Configurable

User

User

Configurable

Spread Percentage

User Configurable

User Configurable
8-pin 150 mil SOIC

Pin Descriptions

Pin Number
Ordering Information

Part / Order Number
252PM 252PMI 252PMLF 252PMILF 252M-XX 252MI-XX 252M-XXLF 252MI-XXLF 252M-XXT 252MI-XXT 252M-XXLFT 252MI-XXLFT

Marking

See Page 7 Above
252M-XX 252MIXX 252MXXL 252MIXXL 252M-XX 252MIXX 252MXXL 252MIXXL

Shipping Packaging

Tubes Tape and Reel Tape and Reel Tape and Reel Tape and Reel

Package
8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC

Temperature
0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C 0 to +70° C -40 to +85° C

Parts that are ordered with a “LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant.

The 252M-XX, 252M-XXLF, 252MI-XX, and 252MI-XXLF are factory programmed versions of the 252PM, 252PMLF, 252PMI, and 252PMILF. A unique “-XX” suffix is assigned by the factory for each custom configuration, and a separate data sheet is kept on file. For more information on custom part numbers programmed at the factory, please contact your local IDT sales and marketing representative.

While the information presented herein has been checked for both accuracy and reliability, IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.

IDT / ICS FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER 9

ICS252

ICS252 FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER

EPROM CLOCK SYNTHESIZER

Originator R.Willner R.Willner R.Willner

R.Willner

R.Willner

R.Willner

Date Description of Change
04/08/05 Preliminary release.
01/16/06 Corrected Block Diagram. Released from Prelim to Final.
06/13/06 Added "-XX" part ordering information and specific note pertaining to custom configurations of device.
08/10/07 Removed “Inernal pull-up resistor” info from PDTS pin description and added extrenal pull-up resistor statement/information.
08/20/07 Changed S1 pin name to “SEL” removed references to PDTS pin changed pull-up resistor value from 190 to 120 kOhms.
03/16/09 Correct page 1 text to have 2 selectable configuration registers.

IDT / ICS FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER 10

ICS252

ICS252 FIELD PROGRAMMABLE DUAL OUTPUT SS VERSACLOCK SYNTHESIZER

EPROM CLOCK SYNTHESIZER

Innovate with IDT and accelerate your future networks. Contact:

For Sales
800-345-7015 408-284-8200 Fax 408-284-2775

For Tech Support

Corporate Headquarters

Integrated Device Technology, Inc.
2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA

Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived ICS252PMT Datasheet file may be downloaded here without warranties.

Datasheet ID: ICS252PMT 636966