872S480BKLF

872S480BKLF Datasheet


ICS872S480

Part Datasheet
872S480BKLF 872S480BKLF 872S480BKLF (pdf)
Related Parts Information
872S480BKLFT 872S480BKLFT 872S480BKLFT
PDF Datasheet Preview
Differential-to-HSTL Zero Delay Clock Generator

ICS872S480

DATA SHEET

The ICS872S480 is a Zero Delay Clock Generator with hitless input clock switching capability. The ICS872S480 is ideal for use in redundant, fault tolerant clock trees where low jitter frequency synthesis are critical. The device receives two differential clock signals from which it generates two outputs with “zero” delay. The output and feedback dividers are configured to allow for a 1:1 frequency generation ratio.

The ICS872S480 Dynamic Clock Switch DCS circuit continuously monitors both input clock signals. Upon detection of an invalid clock input stuck LOW or HIGH for at least one complete clock period of the VCO feedback frequency , the loss of reference monitor will be set HIGH. If that clock is the primary clock, the DCS will switch to the good secondary clock and phase/frequency alignment will occur with minimal output phase disturbance. Once the primary clock is restored to a good state, the DCS will automatically switch back to the primary clock input.

The low jitter characteristics with input clock monitoring and DCS capability make the ICS872S480 an ideal choice for DDR3 applications requiring fault tolerant reference clocks.
• Three differential HSTL output pairs
• Selectable differential CLKx, nCLKx input pairs
• CLKx, nCLKx pairs can accept the following differential
input levels LVPECL, LVDS, HSTL, HCSL
• Output frequency range 350MHz to 950MHz
• Input frequency range 350MHz to 950MHz
• VCO range 970MHz to 2250MHz
• External feedback for “zero delay” clock regeneration
with configurable frequencies
• Static phase offset ±100ps maximum
• Cycle-to-cycle jitter 25ps maximum
• Output skew 20ps maximum
• 3.3V operating voltage supply
• Selectable DDR3 or DDR3 low voltage output
• 0°C to 70°C ambient operating temperature
• Available in lead-free RoHS 6 package

Function Table

Input FREQ_SEL

Output Divider
1 default

Input & Output Frequency MHz

Minimum

Maximum

Output Voltage Table

Input

VOUT_SEL

HSTL Output Style
0 default
1.5V
1.35V

Pin Assignment

VDD REF_SEL AUTO_SEL nc GND nc VOUT_SEL VDD

CLK0 nCLK0

GND CLK1 nCLK1 PLL_BYPASS FB_IN nFB_IN
32 31 30 29 28 27 26 25
24 VDD
23 LOR0
22 LOR1
21 CLK_IND
20 GND
19 FREQ_SEL
18 OE
17 VDDA
9 10 11 12 13 14 15 16
nQFB QFB VDD nQ1 Q1 nQ0 Q0 VDD

ICS872S480
Ordering Information
Table Ordering Information

Part/Order Number 872S480BKLF 872S480BKLFT

Marking ICS72S480BL

Package “Lead-Free” 32 Lead VFQFN “Lead-Free” 32 Lead VFQFN

Shipping Packaging Tray
2500 Tape & Reel

Temperature 0°C to 70°C 0°C to 70°C

NOTE Parts that are ordered with an "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.

While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology IDT assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications, such as those requiring extended temperature ranges, high reliability or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments.
2011 Integrated Device Technology, Inc.

ICS872S480 Data Sheet

DIFFERENTIAL-TO-HSTL ZERO DELAY CLOCK GENERATOR

We’ve Got Your Timing Solution
6024 Silver Creek Valley Road San Jose, California 95138

Sales
800-345-7015 inside USA +408-284-8200 outside USA Fax 408-284-2775

Technical Support
+480-763-2056

DISCLAIMER Integrated Device Technology, Inc. IDT and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.

IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.

Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners.

Copyright All rights reserved.
More datasheets: M85049/20-11N | M85049/20-15N | M85049/20-17N | M85049/20-21N | M85049/20-9N | M85049/20-9W | M85049/20-15W | 02475-01 | DDMN36C4SNA197 | 872S480BKLFT


Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived 872S480BKLF Datasheet file may be downloaded here without warranties.

Datasheet ID: 872S480BKLF 636727