FZL 4146
Part | Datasheet |
---|---|
![]() |
FZL4146GGEGHUMA1 (pdf) |
PDF Datasheet Preview |
---|
Quad Driver Incl. Short-Circuit Signaling Bipolar IC Features q Short-circuit signaling q Four driver circuits for driving power transistors q Turn-ON threshold setting from to 7 V FZL 4146 P-DSO-20-7 Type FZL 4146 G Ordering Code Q67000-H8743 Package P-DSO-20-7 SMD The IC comprises four driver circuits capable of driving power transistors PNP or PMOS . The output transistors are protected against short-circuit to ground and supply voltage. The turn-ON threshold can be set from V to 7 V. Overload at one or several outputs will be indicated at pin SQ signaling output . The corresponding power transistors are then protected by changeover to clock-governed operation. Circuit Description Each driver circuit has one active high driver input Dl and a common enable input ENA active high is provided for all stages. The Q output is designed to drive the output transistors. The load current is sampled and, if necessary, limited via pin W. If the load current exceeds the preset value, the output stage switches off. Switching-ON again is provided by the built-in clock generator T. Its operation requires an external capacitor Ce at pin CE. If Ce is bridged by a break-key, switching-ON can only be carried out by operating this key. The duty cycle of the clock generator is 1:47 e.g. 45 µs/2.1 ms with Ce = 10 nF . The clock generator is privileged versus the current sensor shut down. When the supply is connected, the internal RS-FF goes into the state corresponding to the released output. Semiconductor Group FZL 4146 The turn-ON threshold at input Dl and ENA can be set via pin TS from to 7 V. VTS = 0 V VTS = V 7 V VTS = VS Turn-ON threshold = V Turn-ON threshold = VTS Turn-ON threshold = 7 V Inputs Dl, ENA and W are proof against line break, i.e. an open input at Dl or ENA corresponds to input L, open input W corresponds to overcurrent. If input TS is open, the highest turn-ON threshold is provided. The internal current supply B and the undervoltage monitor UV ensure that in case of a supply voltage that is below the VS turn-OFF threshold, outputs Q and SQ are disabled and the inputs go high-impedance. Basic functioning is possible within the range from VS turn-OFF threshold to V. In case of overcurrent or short-circuit to ground at any output stage the signaling output SQ will go low. In clock-governed operation i.e. when there is automatic switching-ON by the clock and not by a key , SQ goes high and low at the clock rate as long as a shortcircuit or overload is present. SQ is an open-collector output. Any input and output is ESD proof within the limit values. Semiconductor Group Pin Configuration top view P-DSO-20-7 FZL 4146 Semiconductor Group FZL 4146 Pin Definitions and Functions N.C. Function Pin for Ce Enable input for drivers 1 to 4 Input driver 1 Input driver 2 Not connected Ground Input driver 3 Input driver 4 Threshold changeover for all inputs Short-circuit signaling output for drivers 1 to 4 Output current sensor driver 4 Output driver 4 Output current sensor driver 3 Output driver 3 Supply voltage Ground Output current sensor driver 2 Output driver 2 Output current sensor driver 1 Output driver 1 Semiconductor Group FZL 4146 Block Diagram Semiconductor Group FZL 4146 Absolute Maximum Ratings Parameter |
More datasheets: 98056 | FC2131-0000-0002-L | FC2131-0000-0005-L | FC2131-0000-0010-L | DCMAT37S | MDM-9SH025B | 1109 | MA190 | MDM-9PH006F | VMK90-02T2 |
Notice: we do not provide any warranties that information, datasheets, application notes, circuit diagrams, or software stored on this website are up-to-date or error free. The archived FZL4146GGEGHUMA1 Datasheet file may be downloaded here without warranties.